Novel metal-linked face-to-face porphyrazine dimer

We report the synthesis and physical studies of a novel porphyrazine (pz) dimer [1[Ni,Cu]]2, which has Ni(II) ions incorporated into the pz cores and is linked by two Cu(II) ions coordinated to bis(picolinamide) chelates attached to the pz periphery. [1[Ni,Cu]]2 was prepared from precursor pz 2 with a selenodiazole ring fused to the pz core. This ring was deprotected to form the diamino-pz 3, which reacted with 2 mol of picolinoyl chloride hydrochloride to form pz 1[2H,2H], with peripheral bis(picolinamide) chelates; this was metalated to form [1[Ni,Cu]]2. The crystal structures of 1[2H,2H] and [1[Ni,Cu]]2 are presented. The latter is a dimer in which parallel, face-to-face pz's with an average separation of 3.30 angstroms are linked through the peripheral picolinamide ligands by a pair of peripheral Cu(II) ions. Each Cu(II) is coordinated with distorted square-planar geometry by a picolinamide from each pz. In this report, we focus on the interaction of these two peripheral Cu(II) ions. We discuss the preparation and magnetic properties of the pz dimer complex [1[Ni,Cu]]2 with two Cu(II) ions in the peripheral chelate but a diamagnetic metal ion Ni(II) in the pz core. Although [1[Ni,Cu]]2 contains two Cu(II) ions (S = 1/2), we could detect no electron paramagnetic resonance signal, which suggests very strong antiferromagnetic exchange between those two Cu(II) ions. Temperature-dependent magnetic susceptibility measurement gives an exchange splitting between the S = 0 ground state and the excited triplet state of delta = 660 cm(-1).     

Forensic classification of ballpoint pen inks using high performance liquid chromatography and infrared spectroscopy with principal components analysis and linear discriminant analysis

Several varieties of blue ballpoint pen inks were analyzed by high performance liquid chromatography (HPLC) and infrared spectroscopy (IR). The chromatographic data extracted at four wavelengths (254, 279, 370 and 400 nm) was analyzed individually and at a combination of these wavelengths by the soft independent modeling of class analogies (SIMCA) technique using principal components analysis (PCA) to estimate the separation between the pen samples. Linear discriminant analysis (LDA) measured the probability with which an observation could be assigned to a pen class. The best resolution was obtained by HPLC using data from all four wavelengths together, differentiating 96.4% pen pairs successfully using PCA and 97.9% pen samples by LDA. PCA separated 60.7% of the pen pairs and LDA provided a correct classification of 62.5% of the pens analyzed by IR. The results of this study indicate that HPLC coupled with chemometrics provided a better discrimination of ballpoint pen inks compared to IR. The need to develop a suitable IR method for analysing blue ballpoint pen inks has been emphasized and it is hoped that the development of such a method would indeed provide a valuable tool for the non-destructive analysis of blue ballpoint pen ink samples for forensic purposes.     

Laser projection-patterned etching of (100) GaAs by gaseous HCl and CH3Cl

Laser projection-patterned etching of GaAs in a HCl and CH₃Cl atmosphere performed using a pulsed KrF-excimer laser (=248 nm, =15 ns) and deep-UV projection optics (resolution 2 m) is reported. The etching process carried out in a vacuum system having a base pressure of 10^–6 mbar is shown to result from a purely thermochemical reaction. Etching takes place in two steps: (i) between the laser pulses, the etchant gas reacts with the GaAs surface-atomic layer to form chlorination products (mainly As and Ga monochlorides), (ii) local laser surface heating results in the desorption of these products allowing further reaction of the gas with the surface. The influence of the etching parameters (laser energy density, gas pressure and pulse repetition rate) on the etch rate and the morphology of the etched features was studied. Etch rates up to 0.15 nm per pulse, corresponding to the removal of 0.5 GaAs molecular layer, are achieved. The spatial resolution of the etching process is shown to be controlled by the heat spread in the semiconductor and by the nonlinear dependence of the etch rate on the surface temperature. As a result, etched features smaller or larger than the projected features of the photomask are achieved depending on the laser energy density. Etched lines having a width of 1.3 m were obtained at low fluences by the projection of 2 m wide lines onto the GaAs surface.     

A convenient method for 3-pyrroline synthesis

[reaction: see text]. The synthesis of a range of 3-pyrrolines has been achieved from primary amine starting materials using a two-step alkylation/alkylidene carbene CH-insertion reaction sequence. We have shown that insertion into a range of CH-bond types is possible, and the formation of nitrogen-bearing quaternary stereocenters is a relatively facile process. The insertion reaction occurs with >95% retention of stereochemistry, but the presence of protecting groups on nitrogen is generally deleterious to the cyclization process.     

Charge separation versus recombination in dye-sensitized nanocrystalline solar cells: the minimization of kinetic redundancy

In this paper we focus upon the electron injection dynamics in complete dye-sensitized nanocrystalline metal oxide solar cells (DSSCs). Electron injection dynamics are studied by transient absorption and emission studies of DSSCs and correlated with device photovoltaic performance and charge recombination dynamics. We find that the electron injection dynamics are dependent upon the composition of the redox electrolyte employed in the device. In a device with an electrolyte composition yielding optimum photovoltaic device efficiency, electron injection kinetics exhibit a half time of 150 ps. This half time is 20 times slower than that for control dye-sensitized films covered in inert organic liquids. This retardation is shown to result from the influence of the electrolyte upon the conduction band energetics of the TiO2 electrode. We conclude that optimum DSSC device performance is obtained when the charge separation kinetics are just fast enough to compete successfully with the dye excited-state decay. These conditions allow a high injection yield while minimizing interfacial charge recombination losses, thereby minimizing "kinetic redundancy" in the device. We show furthermore that the nonexponential nature of the injection dynamics can be simulated by a simple inhomogeneous disorder model and discuss the relevance of our findings to the optimization of both dye-sensitized and polymer based photovoltaic devices.