Effect of alkylated diphenylamine on thermal-oxidative degradation behavior of poly-<Emphasis Type="Italic">α</Emphasis>-olefin

An oil-soluble antioxidant, alkylated diphenylamine (ADPA), was prepared by alkylation of diphenylamine. The influence of ADPA on the thermal-oxidative stability of poly-α-olefin (PAO8) was evaluated by thermogravimetry (TG). For comparison, the thermal-oxidative stability of PAO8 with zinc dialkyl dithiophosphate (ZDDP) was also investigated. Activation energy (E_a)of the corresponding thermal-oxidative degradation process was evaluated by the Flynn-Wall-Ozawa (FWO) and Kissinger-Akahira-Sunose (KAS) methods. To demonstrate the reliability of the kinetic study, the antioxidant performance of ADPA and ZDDP in PAO8 was also studied by the pressure drop (PDT) and accelerated oxidation (AOT) tests. The results indicate that ADPA has better antioxidant ability than ZDDP in increasing the E_a value and enhancing the oxidative stability of PAO8. Good correlation between the applied test methods was established.     

Density of lithium fluoride—lithium carbonate-based molten salts

The density of the LiF-Li₂CO₃ melts system was measured using the Archimedean method. Using the quadratic regression orthogonal design with two factors, a regression equation for the density of LiF-Li₂CO₃ melts was obtained in which the concentration of LiF and temperature were considered. The results indicated that the density of the LiF-Li₂CO₃ melts decreased with either increasing the concentration of LiF or increasing temperature; a linear relation was observed between density and temperature. In addition, the influences of NaF, KF, NaCl, and KCl additives on the densities of the given systems were studied. The addition of NaF and KF increased the density of the melts, whereas NaCl and KCl resulted in an initial increase and subsequent decrease with an increasing additive concentration. The density attained a maximum at NaCl and KCl mass fraction of approximately 15%.     

Efficient method for the synthesis of polysubstituted 2,6-dicyanoanilines by one-pot three-component tandem reaction of malononitrile with <Emphasis Type="Italic">α</Emphasis>,<Emphasis Type="Italic">β</Emphasis>-unsaturated imines

A facile and efficient one-pot synthesis of polysubstituted benzenes was achieved via the Michael addition of malononitrile with α,β-unsaturated imines and a sequential tandem reaction. This reaction generates polysubstituted 2,6-dicyanoanilines in high yields (15 examples, isolated yields of 57–91 %), and proceeds under mild reaction conditions (60°C, 10 min). In addition, a possible mechanism accounting for the reaction is proposed.     

The significance of a second adsorption phase with weakly adsorbed species for the calculation of the surface concentrations of a mixture: methanol–DME and methanol–ethene adsorption in SAPO-34

With the calorimetric (adsorption heat versus coverage) curve also measured together with the adsorption isotherm, the simultaneous use of both curves showed that there were two phases of adsorption in the adsorption of methanol, dimethyl ether, ethene and propane in SAPO-34. The dual-site Langmuir equation gave good fits to the adsorption data to support the interpretation that a second (type 2) adsorption phase occurred in the high-pressure region in addition to a first (type 1) adsorption phase on the acid sites at lower pressures. Adsorption experiments and calculations using binary gas mixtures showed that due to the existence of two types of adsorption, the multicomponent Langmuir isotherm equation (Langmuir competitive adsorption model) calculated incorrect surface concentrations when the concentrations were high. In contrast, the ideal adsorbed solution theory (IAST) calculated correct surface concentrations in the adsorption of mixtures.     

Direct Imaging of Octahedral Distortion in a Complex Molybdenum Vanadium Mixed Oxide

Complex Mo,V‐based mixed oxides that crystallize in the orthorhombic M1‐type structure are promising candidates for the selective oxidation of small alkanes. The oxygen sublattice of such a complex oxide has been studied by annular bright field scanning transmission electron microscopy. The recorded micrographs directly display the local distortion in the metal oxygen octahedra. From the degree of distortion we are able to draw conclusions on the distribution of oxidation states in the cation columns at different sites. The results are supported by X‐ray diffraction and electron paramagnetic resonance measurements that provide integral details about the crystal structure and spin coupling, respectively.     

Whole‐Genome Sequencing of a Single Viral Species from a Highly Heterogeneous Sample

Metagenomic studies suggest that only a small fraction of the viruses that exist in nature have been identified and studied. Characterization of unknown viral genomes is hindered by the many genomes populating any virus sample. A new method is reported that integrates drop‐based microfluidics and computational analysis to enable the purification of any single viral species from a complex mixed virus sample and the retrieval of complete genome sequences. By using this platform, the genome sequence of a 5243 bp dsDNA virus that was spiked into wastewater was retrieved with greater than 96 % sequence coverage and more than 99.8 % sequence identity. This method holds great potential for virus discovery since it allows enrichment and sequencing of previously undescribed viruses as well as known viruses.     

Copper‐Mediated Formation of Aryl,Heteroaryl, Vinyl and Alkynyl Difluoromethylphosphonates: A General Approach to Fluorinated Phosphate Mimics

A general and efficient access to aryl, heteroaryl, vinyl and alkynyl difluoromethylphosphonates is described. The developed methodology using TMSCF₂PO(OEt)₂, iodonium salts and a copper salt provided a straightforward manifold to reach these highly relevant products. The reaction proved to be highly functional group tolerant and proceeded under mild conditions, giving the corresponding products in good to excellent yields. This method represents the first general synthetic route to this important class of fluorinated scaffolds, which are well‐recognized as in vivo stable phosphate surrogates.     

The Unexpected Influence of Precursor Conversion Rate in the Synthesis of III–V Quantum Dots

Control of quantum dot (QD) precursor chemistry has been expected to help improve the size control and uniformity of III–V QDs such as indium phosphide and indium arsenide. Indeed, experimental results for other QD systems are consistent with the theoretical prediction that the rate of precursor conversion is an important factor controlling QD size and size distribution. We synthesized and characterized the reactivity of a variety of group‐V precursors in order to determine if precursor chemistry could be used to improve the quality of III–V QDs. Despite slowing down precursor conversion rate by multiple orders of magnitude, the less reactive precursors do not yield the expected increase in size and improvement in size distribution. This result disproves the widely accepted explanation for the shortcoming of current III–V QD syntheses and points to the need for a new generalizable theoretical picture for the mechanism of QD formation and growth.