Some Aspects of Magnetic Filtration Theory for Removal of Fine Particles from Aqueous Suspensions

The magnetic filtration theory was evaluated to intensify the filtration of industrial fluids by magnetic filters. Effects of filtration velocity and external magnetic field intensity on filter performance were investigated and the dependence of the logarithmic efficiency coefficient on filtration velocity was questioned. It was concluded that change in the magnetic susceptibility of the dispersion particles, caused by external magnetic field, and change in the flow rate properties of the liquid alongside the filter pores are the most essential factors to be considered in the design, development, and modeling of magnetic filtration systems in various industrial areas.     

Structural and transport properties of Sn–Mg alloys

In this work, the structural and transport properties of Mg-doped Sn-based alloys have been investigated. The temperature-dependent transport and structural properties of Sn–Mg alloys were investigated for five different samples (Pure Sn, Sn-1.0 wt% Mg, Sn-2.0 wt% Mg, Sn-6.0 wt% Mg and Pure Mg). Scanning electron microscopy (SEM), X-ray diffraction and energy dispersive X-ray analysis measurements were carried out in order to clarify the structural properties of the samples. It was found that the samples had tetragonal crystal symmetry, except for pure Mg which had hexagonal crystal symmetry. We also found that the cell parameters changed slightly with the addition of Mg element. The SEM micrographs of the samples showed that they had smooth surfaces with a clear grain boundary. The electrical and thermal conductivity of the samples were measured by four-point probe and the radial heat flow method, respectively. The electrical resistivity of the samples increased almost linearly with the increasing temperature. The thermal conductivity values ranged between 0.60 and 1.00 W/Km, while they decreased slightly with temperature and increased with Mg composition. The thermal conductivity values of the alloys were in between the values of pure Sn and Mg. The thermal conductivity results of the alloys were compared with other available results, and a good agreement was seen between the results. In addition, the temperature coefficients of electrical resistivity and thermal conductivity were determined; these were independent of the composition of the alloying elements.     

Effect of reactive and nonreactive surface modifications and compatibilizer use on mechanical and flame-retardant properties of linear low-density polyethylene filled with huntite and hydromagnesite mineral

Journal of Thermal Analysis and Calorimetry - In the current study, huntite and hydromagnesite (HH) was used as flame-retardant additive in linear low-density polyethylene (LLDPE). The effect of HH...     

Physical properties (thermal,thermomechanical, magnetic,and adhesive) of some smart orthodontic wires

Thermal, thermomechanical, and caloric properties of commercial orthodontic wires (produced by Natural Orthodontics Corp., USA) with cylindrical and rectangular geometry were studied. Depending on the applied forces, there were identified the range of elasticity, the elasticity–viscoelasticity coexistence domain and the domain in which a maximum force of 18 N is applied, for the orthodontic wires. When increasing the thickness of orthodontic wires, deformation decreases. The Controlled Force Module, in the tension mode, was used for the determination of the orthodontic wires elongation at application of the stretching forces from 0 to 13 N, at 35 °C, maintaining each static force value for 3 min. The increase in the cross-sectional area of the orthodontic wires disfavors the process of elongation of the sample, at the same applied static force. Using the Multi-Frequency–Strain–Stress modulus, in the tension mode, DMA cyclic heating–cooling measurements were performed. The measured physical quantities for orthodontic wires were Storage Modulus, Loss Modulus, Tanδ and Stiffness, at heating and cooling. Thus, the characteristic temperatures of the phase transitions (A_s, A_f, M_s, M_f), of all the studied orthodontic wires were identified. Also, the values of the elasticity modulus (Young’s Modulus) of the orthodontic wires were calculated at 35 °C. With the DSC Q200 device, using temperature-modulated differential scanning calorimetry method, a multi-step temperature variation program, was applied to a rectangular wire, in three stages (cooling–heating–cooling). Through the interpretation of heat fluxes (reversible, irreversible and total), the phase transitions in the formation of martensite, austenite, but also of the rombohedral phase (R-phase), were identified. Formations of austenite and martensite were also evidenced by the classical DSC method, but the classical DSC method also enabled the R-phase identification. The adherence of some food dyes on the orthodontic wires, as well as the modification of the surface roughness of the orthodontic wire after the deposition of the food dye, was also studied. By magnetic measurements, it was established that the orthodontic wires had paramagnetic properties at room temperature, and nitinol was a mixture of 49.2% austenite and 50.8% martensite.

     

Ffast Transient Fluorescence Technique to Study Critical Exponents at the Glass Transition

The fast transient fluorescence (FTRF) technique was used to study critical exponents at the glass transition in free-radical crosslinking copolymerization (FCC) for two different monomeric systems, methyl methacrylate (MMA) and styrene (S). Pyrene (P_y ) was used as a fluorescence probe. The fluorescence lifetimes of P_y from its decay traces were measured and used to monitor the gelation process. Changes in the viscosity of the pregel solutions due to glass formation dramatically enhance the fluorescent yield of aromatic molecules. This effect is used to study the glass transition upon gelation of MMA and S monomeric systems as a function of time, at various temperatures and crosslinker concentrations. The results are interpreted in the view of percolation theory. The gel fraction and weight average degree of polymerization exponents β and γ are found to be 0.37 ± 0.02 and 1.66 ± 0.07 in agreement with percolation results.     

Phase transitions and metastable states in TlGaSe2

The results of measurements of the dielectric constant of TlGaSe₂ in temperature range of successive phase transitions are presented. An anomaly in the temperature dependence of the real part of dielectric constant in TlGaSe₂ has been observed at about 242?K in addition to anomalies at 115, 108, and also near 65?K as reported in previous publications. The presence of temperature hysteresis effects in temperature interval between 115 and 242?K allowed making a conclusion about possible existence of an incommensurate phase in the mentioned temperature range. A model of succession of the structural phase transitions in TlGaSe₂ has been suggested.