Electrical properties of neodymium doped CaBi4Ti4O15 ceramics

Neodymium doped bismuth layer structure ferroelectrics (BLSFs) ceramics CaBi_4−xNd_xTi₄O₁₅ (x=0, 0.25, 0.50, 0.75) were prepared by solid-state reaction method. X-ray diffraction pattern showed that single phase was formed when x=0-0.75. The refined lattice parameters showed that a (b) axes decrease at x=0.25 and increase with more Nd³⁺ dopant. The effects of Nd³⁺ doping on the dielectric and ferroelectric properties of CaBi₄Ti₄O₁₅ ceramics are studied. Nd³⁺ dopant decreased the Curie temperature linearly, and the dielectric loss, tan δ, as well. The remnant polarization of Nd³⁺ doped CaBi₄Ti₄O₁₅ ceramics was increased by 80% at x=0.25, while more Nd³⁺ dopant decreased the remnant polarization. CaBi_3.75Nd_0.25Ti₄O₁₅ ceramics had the largest piezoelectric constant d₃₃. The structure and properties of CaBi_4−xNd_xTi₄O₁₅ ceramics showed that Nd³⁺ may occupy different crystal locations when Nd³⁺ content x is less than 0.25 and more than 0.50.     

Deposition of Hydrogen-Free Silicon Nitride Thin Films by Microwave ECR plasma Enhanced Magnetron Sputtering at Room Temperature

Hydrogen-free silicon nitride （SiNx） films were deposited at room temperature by microwave electron cyclotron resonance （MW-ECR） plasma enhanced unbalance magnetron sputtering system. Both Fourier-transform infrared spectroscopy and x-ray photoelectron spectroscopy are used to study the bonding type and the change of bonding structures of the silicon nitride films. The results indicate that the chemical structure and composition of SiNx films deposited by this technique depend strongly on the N2 flow rates, the stoichiometric SiNx film, which has the highest hardness of 22.9 GPa, could be obtained at lower N2 flow rate of 4 sccm.     

Ultraviolet Luminescence in Mg0.12Zn0.88O Alloy Films

We investigate the origin of ultraviolet （UV） emission from Mg0.12 Zn0.88 O alloy thin films with a wurtzite structure fabricated on c-plane Al2O3 substrates by plasma assisted molecular beam epitaxy. At room temperature, the absorption edge and UV emission band of the Mg0.12Zn0.88O film shift to high-energy side compared with ZnO films. Temperature dependence of the photoluminescence spectra shows that the UV emission is composed of free exciton and neutral donor bound exciton emissions. Two-step dissociation processes of the UV emission are observed with the increasing temperature. The thermal quenching mechanism is attributed to the dissociation of the free exciton from the neutral donor bound exciton in the low temperature region and the dissociation of free electron and hole from the free exciton in the high temperature region.     

三核铜（I）配合物的合成与荧光光谱

室温下，通过双核配合物[Cu(dppm)(NO3)]2(dppm=双二苯基膦甲烷)与四苯基硼钠在甲醇和二氯甲烷混合溶剂中反应制备了三核铜(I)配合物[Cu3(dppm)3(NO3)(OH)](NO3)，经过红外光谱、热重分析、核磁和ES-MS等现代分析手段表征了配合物的物理化学性质，并进一步研究了配合物在室温下的荧光光谱特征。     

A stable dual-wavelength fiber laser with tunable wavelength spacing using a polarization-maintaining linear cavity

We propose and experimentally demonstrate a stable dual-wavelength erbium-doped polarization-maintaining (PM) fiber laser with tunable wavelength spacing using an all-PM linear cavity that makes use of two reflection peaks from the PM fiber Bragg grating (PM-FBG). Experimental results show stable dual lasing lines with a wavelength separation of ∼0.22 nm and a large optical signal-to-noise ratio (OSNR) of over 40 dB under room temperature. By applying axial strain to the PM-FBG, the center wavelengths of the two lasing lines can be tuned over several nanometers and the wavelength separation between the lasing lines can also be tuned to as small as 0.05 nm, which, to our knowledge, is the smallest wavelength spacing ever obtained from a stable room-temperature dual-wavelength fiber laser. The proposed laser configuration has the advantages of simple structure, low loss, stable dual-wavelength operation and a very small lasing linewidth of ∼5 kHz . PACS 42.55.Wd; 42.81.-i; 42.81.Gs     

Low Cost, High Efficiency, Gain Flattened L Band EDFA Using FBGs as C Band Seed Generators

A low cost, coolerless 980nm diode pumped, gain flattened L band EDFA with fast transient control, high pump efficiency and gain clamping effect was realized by using FBGs as C band seed generators.     

电致发光色纯性增强的硅基有机微腔

报道了硅基有机微腔的电致发光（EL）.该微腔由上半透明金属膜、中心有源多层膜和多孔硅分布Bragg反射镜（PS DBR）组成.半透明金属膜由Ag（２０nm）构成，充当发光器件的负电极和微腔的上反射镜.有源多层膜由Al (1 nm) / LiF(05 nm) /Alq3/Alq3:DCJTB/NPB/CuPc/ITO/SiO2组成，其中的Al/LiF为电子注入层，ITO为正电极，SiO2为使正、负电极电隔离的介质层.该PS DBR是采用设备简单、成本低廉且非常省时的电化学腐蚀法用单晶Si来制备的；该PS 关键词： 电化学腐蚀 电致发光 窄峰发射 硅基有机微腔     

Preparation and characterization of acrylic‐based black particles of poly(methyl methacrylate‐co‐ethylene glycol dimethacrylate) by dispersion polymerization for electrophoretic displays

Ultrafine black particles, ranging in diameter from 1 to 3 μm, were prepared by dispersion polymerization in a methanol/water mixture with vinyl monomers, nonpolymerizable Sudan black B dyes, and fluorescein isothiocyanate labeled charge control additives. Both the ratio of the methanol to the water dispersion medium and the polymeric stabilizer concentration had significant effects on the particle size. The important role of the stabilizer concentration lay in the particle formation step, during which it determined the particle stability and final particle size. These could affect the extent of the aggregation of nuclei by changing the adsorption rate of the stabilizer and the viscosity of the dispersion medium, resulting in smaller particles. The fluorescent‐labeled charge control additives strongly affected the electrophoretic mobility. A small concentration of fluorescent‐labeled charge control additives increased the electrophoretic mobility. However, a further addition reduced the electrophoretic mobility of the polymer particles. The concentration dependence of the fluorescent‐labeled charge control additives on the deposition behavior in the polymer particles was successfully imaged and thereafter quantified by image analysis. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 5608–5616, 2004