Arsenic determination in marine sediment using ultrasound for sample preparation.

This work deals with As determination in marine sediment using ultrasound for sample preparation. It is shown that As can be quantitatively extracted from marine sediment using 20% (v/v) HCl and sonication. The slurry is centrifuged and the analyte is determined in the supernatant by hydride generation atomic absorption spectrometry (HG AAS). A flow injection (FI) system is employed for hydride generation, with 0.5% (m/v) NaBH(4) used as reducdant and a 20% (v/v) HCl used as sample carrier. The limit of quantification is 1.6 microg g(-1) of As, which is based on 800 microl of sample solution and 0.200 g of sample mass in a volume of 50 mL. Certified and non certified marine sediment samples were analyzed; the results were in accordance with the certified or reference values. Speciation analysis by HPLC-ICP-MS showed that As(V) is the only detectable As species present in the supernatant of the centrifuged sample.     

Fully developed mixed convection in horizontal and inclined tubes with uniform heat flux using nanofluid

Fully developed laminar mixed convection of a nanofluid consists of water and Al₂O₃ in horizontal and inclined tubes has been studied numerically. Three-dimensional elliptic governing equations have been solved to investigate the flow behaviors over a wide range of the Grashof and Reynolds numbers. Comparisons with previously published experimental and numerical works on mixed convection in a horizontal and inclined tube are performed and good agreements between the results are observed. Effects of nanoparticles concentration and tube inclinations on the hydrodynamics and thermal parameters are presented and discussed. It is shown that the nanoparticles concentration does not have significant effects on the hydrodynamics parameters. Heat transfer coefficient increases by 15% at 4 Vol.% Al₂O₃. Skin friction coefficient continually increases with the tube inclination, but the heat transfer coefficient reaches a maximum at the inclination angle of 45°.     

Multi-mode wave propagation in ribbed plates: Part I,wavenumber-space characteristics

This paper addresses the issue of energy propagation features in ribbed panels over a wide frequency range. First, a tool for estimating the wave propagation characteristics of one- and two-dimensional structures by k-space analysis is presented. This tool uses a concept of Inhomogeneous Wave Correlation with sparse measured or extracted data, and leads to the estimation of θ-dependent wavenumbers. Here, the method is employed with the sparse simulated and measured normal velocities of a set of ribbed panels and new insights into their k-space behavior are highlighted. Behavior is essentially characterized at low frequencies by structural orthotropy. Comparisons with homogenized data show very good agreement. At higher frequencies, a new behavior pattern is observed and explained both numerically and experimentally. This is a multi-modal waveguide type of propagation in a direction parallel to the ribs.     

Buckling of a stiff thin film on a compliant substrate in large deformation

A finite-deformation theory is developed to study the mechanics of thin buckled films on compliant substrates. Perturbation analysis is performed for this highly nonlinear system to obtain the analytical solution. The results agree well with experiments and finite element analysis in wavelength and amplitude. In particular, it is found that the wavelength depends on the strain. Based on the accurate wavelength and amplitude, the membrane and peak strains in thin films, and stretchability and compressibility of the system are also obtained analytically.     

Multi-layer thin films/substrate system subjected to non-uniform misfit strains

Current methodologies used for the inference of thin film stress through curvature measurement are strictly restricted to stress and curvature states that are assumed to remain uniform over the entire film/substrate system. These methodologies have recently been extended to a single layer of thin film deposited on a substrate subjected to the non-uniform misfit strain in the thin film. Such methodologies are further extended to multi-layer thin films deposited on a substrate in the present study. Each thin film may have its own non-uniform misfit strain. We derive relations between the stresses in each thin film and the change of system curvatures due to the deposition of each thin film. The interface shear stresses between the adjacent films and between the thin film and the substrate are also obtained from the system curvatures. This provides the basis for the experimental determination of thin film stresses in multi-layer thin films on a substrate.     

Application of the wavelet transform for a channel flow in a mixed convection phenomenon

The aim of this paper is to investigate laminar-turbulent transition in a mixed convection phenomenon occurring in a horizontal rectangular duct. Indeed, laminar-turbulent transition is well known in the case of forced convection but the presence of secondary flow induced by natural convection on this transition is not well highlighted. In this study, we will not be concerned by determining a critical threshold value of a Reynolds number of transition but only to estimate the degree of turbulence in the transition regime, i.e. weak turbulence in the case of a mixed convection phenomenon. This is possible thanks to the application of the wavelet transform. The calculation of the Hölder exponent, associated with the maximum value of the singularity spectrum for various experimental conditions allows the degree of turbulence to be measured. The variation of the Hölder exponent versus heat flux and Reynolds number enables us to show that there are two ways to go towards turbulence: thermal by increasing heat flux and hydrodynamic by increasing fluid velocity.     

Closed-form solutions for a rectangular layer with central crack under anti-plane shear stress

We consider the problem of determining the stress distributionin a finite rectangular elastic layer containing a Griffithcrack which is opened by internal shear stress acting alongthe length of the crack. The mode III crack is assumed to belocated in the middle plane of the rectangular layer. The followingtwo problems are considered: (A) the central crack is perpendicularto the two fixed lateral surfaces and parallel to the othertwo stress-free surfaces; (B) all the lateral surfaces of therectangular layer are clamped and the central crack is parallelto the two lateral surfaces. By using Fourier transformations,we reduce the solution of each problem to the solution of dualintegral equations with sine kernels and a weight function whichare solved exactly. Finally, we derive closed-form expressionsfor the stress intensity factor at the tip of the crack andthe numerical values for the stress intensity factor at theedges of the cracks are presented in the form of tables.     

Combined supercritical-fluid chromatography/mass spectrometry in the analysis of diuron in plasma using on-line phase-system switching

On-line sample pretreatment by means of the phase-system switching approach is an interesting technique for the analysis of aqueous samples, e.g., plasma, by means of supercritical-fluid chromatography. In order to analyse plasma samples the following analytical procedure is used. The plasma sample is injected on to a short precolumn, which is washed with water and subsequently dried with nitrogen. Next, the solutes are desorbed with the supercritical mobile phase, analysed with packed-column supercritical-fluid chromatography and detected with either a UV detector or a mass spectrometer, equipped with a moving-belt interface. The herbicide diuron is selected as a test compound to study the feasibility of this approach. Using a selective detector the procedure is sufficiently sensitive to detect diuron in plasma, but not appropriate to detect the diuron metabolites in a post-mortem plasma sample. These have been identified with liquid chromatography/mass spectrometry. The detection limit of diuron in plasma using the procedure described is about 30 ng/mL.     

Characterization of thermal diffusion in polymer solutions by thermal field-flow fractionation: Dependence on polymer and solvent parameters

The thermal diffusion coefficient D_T has been obtained for 17 polymer-solvent combinations, each of them spanning a range of polymer molecular weights, using thermal field-flow fractionation. The polymers examined include polystyrene, poly(alpha-methyl)styrene, polymethylmethacrylate, and polysioprene. The solvents include benzene, toluene, ethylbenzene, tetrahydrofuran, methylethylketone, ethylacetate, and cyclohexane. Although D_T was confirmed as essentially independent of polymer molecular weight, it was found to vary substantially with the chemical composition of polymer and solvent. The results were used to evaluate several thermal diffusion theories; the agreement with theory was generally found to be unsatisfactory. Attempts were then made to correlate the measured thermal diffusion coefficients with various physicochemical parameters of the polymers and solvent. A good correlation was found in which D_T increases with the thermal conductivity difference of the polymer and solvent and varies inversely with the activation energy of viscous flow of the solvent.     

A test problem for molecular dynamics integrators

We derive a test problem for evaluating the ability of time-steppingmethods to preserve the statistical properties of systems inmolecular dynamics. We consider a family of deterministic systemsconsisting of a finite number of particles interacting on acompact interval. The particles are given random initial conditionsand interact through instantaneous energy- and momentum-conservingcollisions. As the number of particles, the particle density,and the mean particle speed go to infinity, the trajectory ofa tracer particle is shown to converge to a stationary Gaussianstochastic process. We approximate this system by one describedby a system of ordinary differential equations and provide numericalevidence that it converges to the same stochastic process. Wesimulate the latter system with a variety of numerical integrators,including the symplectic Euler method, a fourth-order Runge-Kuttamethod, and an energyconserving step-and-project method. Weassess the methods' ability to recapture the system's limitingstatistics and observe that symplectic Euler performs significantlybetter than the others for comparable computational expense.