Influence of wall heat loss on the emission characteristics of premixed ammonia-air swirling flames interacting with the combustor wall

The influence of wall heat loss on the emission characteristics of ammonia-air swirling flames has been investigated employing Planar Laser-Induced Fluorescence imaging of OH radicals and Fourier Transform Infrared spectrometry of the exhaust gases in combustors with insulated and uninsulated walls over a range of equivalence ratios, ?, and pressures up to 0.5 MPa. Strong influence of wall heat loss on the flames led to quenching of the flame front near the combustor wall at 0.1 MPa, resulting in large unburned NH₃ emissions, and inhibited the stabilization of flames in the outer recirculating zone (ORZ). A decrease in heat loss effects with an increase in pressure promoted extension of the fuel-rich stabilization limit owing to increased recirculation of H₂ from NH₃ decomposition in the ORZ. The influence of wall heat loss resulted in emission trends that contradict already reported trends in literature. NO emissions were found to be substantially low while unburned NH₃ and N₂O emissions were high at fuel-lean conditions during single-stage combustion, with values such as 55 ppmv of NO, 580 ppmv of N₂O and 4457 ppmv of NH₃ at ? = 0.8. In addition, the response of the flame to wall heat loss as pressure increased was more important than the effects of pressure on fuel-NO emission, thereby leading to an increase in NO emission with pressure. It was found that a reduction in wall heat loss or a sufficiently long fluid residence time in the primary combustion zone is necessary for efficient control of NH₃ and N₂O emissions in two-stage rich-lean ammonia combustors, the latter being more effective for N₂O in addition to NO control. This study demonstrates that the influence of wall heat loss should not be ignored in emissions measurements in NH₃-air combustion, and also advances the understanding of previous studies on ammonia micro gas turbines.     

Minimization of erase-band in shingled PMR with asymmetric writer

To make the write-field much stronger with sharper cross-track field gradient in Shingled perpendicular Magnetic Recording (SMR), we have successfully developed asymmetric SMR heads with one-side shield design. Using these heads, higher track density capability on the shielded-side was demonstrated, which came from narrower erase-band width at shielded side.     

Geometrical Form Factor Improvement for Receiving System of Infrared Lidar

Improvement of an infrared light detection and ranging (IR-lidar) system for a short range (0–1000 m) and with high resolution is studied to enhance a geometrical form factor. Theoretical modeling of Mie scattering echo signals agrees with the experimental results. Introduction of a lens in front of the detector is effective for increasing the geometrical form factor, and a significant improvement in the received signal intensity is achieved, especially for short-range measurements around 100 m. This is useful for the IR-lidar system with a detector diameter of less than 1 mm. In the theoretical model, a ray-tracing technique was applied and a transmitting laser beam with Gaussian profile was considered for better accuracy.     

Synthesis of new photoresponsive polyesters containing norbornadiene moieties by the ring‐opening copolymerization of donor–acceptor norbornadiene dicarboxylic acid anhydride with donor–acceptor norbornadiene dicarboxylic acid monoglycidyl ester derivatives

The ring‐opening copolymerization of donor–acceptor norbornadiene (D–A NBD) dicarboxylic acid monoglycidyl ester derivatives with D–A NBD dicarboxylic acid anhydride was performed with tetraphenylphosphonium bromide as a catalyst in toluene to produce new norbornadiene (NBD) polyesters containing D–A NBD moieties in the main chain and in the side chain in one step in good yields. The photoisomerization of the D–A NBD moieties in these polyesters proceeded very smoothly to give the corresponding quadricyclane groups. Because these NBD polyesters contained many NBD moieties in the polymer chain, they had the highest capacity for heat storage in the D–A NBD polymers reported so far. The stored thermal energy of the irradiated polyesters was evaluated by differential scanning calorimetry analysis to be approximately 150–190 J/g. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 4412–4421, 2005     

Water-soluble constituents of dill

From the water-soluble portion of the methanol extract of dill (fruit of Anethum graveolens L.), which has been used as a spice and medicine, thirty-three compounds, including a new monoterpenoid, six new monoterpenoid glycosides, a new aromatic compound glucoside and a new alkyl glucoside were obtained. Their structures were clarified by spectral investigation.     

Radiative heat transfer analysis in pure water heater used for semiconductor processing

A simplified one-dimensional model is presented to analyze the non-gray radiative transfer in pure water heater used in the rinsing processes within semiconductor production lines, and the ray-tracing method is extended to simulate the radiative heat transfer. To examine the accuracy of the simplified model, the distribution of radiation absorption is determined by the ray-tracing method based the simplified model and compared with the data obtained by three-dimensional non-gray model in combination with Monte Carlo method in reference, and the effects of the water thickness on the radiation absorption are analyzed. The results show that the simplified model has a good accuracy in solving the radiation absorption in the pure water heater. The radiation absorption increases with the water thickness, but when the water thickness is greater than , the radiation absorption increases very slowly with the water thickness.     

Unwinding of DNA polymerases by the antitumor drug,cis-diamminedichloroplatinum(II)

The helix-turn-helix motifs of the DNA binding domains of human polymerase-alpha and polymerase-kappa are dramatically perturbed upon binding to cisplatin with concomitant release of zinc.