Development of new dyes for use in integrated optical sensors

New chromoionophores have been developed, focused on NIR applications so that optode membranes may be used in monolithically integrated optical sensors. The wavelength of maximum absorbance has been estimated for a new model compound by the Pariser-Parr-Pople (PPP) method. Several cyanine type dyes have been tested as membrane chromoionophores. Membrane composition has been altered to overcome solubility problems. In this way, simple pH-sensitive optode membranes have been produced.     

Toughening of epoxies via craze-like damage

The fracture behavior of a core-shell rubber (CSR) modified epoxy is investigated using both fracture mechanics and microscopy tools. The CSR-modified epoxy is found to be toughened via numerous line-array cavitations of the CSR particles, followed by plastic flow of the epoxy matrix. The toughening effect via the above craze-like damage process is found to be as effective as that of the well-known widespread rubber cavitation/matrix shear yielding mechanisms. The conditions for triggering the craze-like damage appear to be both stress state and rubber concentration dependent. The type of rubber tougheners utilized also plays a critical role in triggering this rather unusual craze-like damage in epoxy systems. © 1993 John Wiley & Sons, Inc.     

Chemical composition and reaction analysis of single aerosol particles

In situ measurements of gas-liquid surface reactions of single aerosol microdroplets are presented. By means of optical levitation in combination with elastic (Mie) and inelastic (Raman) light scattering it is possible to get information on the chemistry of e.g. acid/base reactions as well as the physical behavior of single microparticles.     

Solution of the 2D ising model on a triangular lattice by the method of auxiliaryq-deformed Grassmann fields

A representation in the form of a functional integral is obtained for the partition function of the inhomogeneous 2D Ising model on a triangular lattice where the coupling parameters are arbitrary functions of coordinates. The method for transforming the partition function into an integral uses an auxiliary six-component Grassmann field in which the Grassmann fields corresponding to one of the components commute with the others. Thus, one pair of components realizes a representation of the q-deformed group SL_q(2, R) with q=–1 and the other two pairs correspond to the usual Grassmann spinors (q=1). An explicit expression in terms of the modified Pfaffian is found for the Gaussian integral over these fields and its relation to the ordinary Grassmann functional integral is established.Translated from Teoreticheskaya i Matematicheskaya Fizika, Vol. 109, No. 3, pp. 441–463, December, 1996.     

THE USE OF THERMOELASTICITY TO EVALUATE STRESS REDISTRIBUTION AND NOTCH SENSITIVITY IN CERAMIC MATRIX COMPOSITES

Thermoelastic stress analysis was used to document the effect of composite damage on the stress distribution in three ceramic matrix composites. Composite damage was found to significantly alter the thermoelastic response of each material, with the greatest effect noted in SiC/CAS. Thermoelastic imaging of these materials affords a more complete picture of how the various damage mechanisms affect the stress distribution. In particular, a stress concentration factor computed from thermoelastic images, serves as an indicator of stress redistribution. The stress concentration factors were computed by comparing notch root to far field temperatures, and monitored after the introduction of various amounts of damage. In each material, the stress concentration factor diminished as the damaging load approached the ultimate stress. Reduction in the stress concentration is associated with local changes in modulus, mechanistically arising from combinations of fiber, matrix and interface fracture. Stress redistribution occurs as a consequence of modulus changes, leading to lower notch sensitivity in each of the tested composites.     

Hybrid free radical/cationic frontal photopolymerizations

The irradiation of hybrid photopolymer systems consisting of a free radically polymerizable multifunctional acrylate monomer and a cationically polymerizable epoxide or oxetane monomer was conducted under conditions where only the free radical polymerization takes place. This results in the formation of a free‐standing polyacrylate network film containing quiescent oxonium ions along with the unreacted cyclic ether monomer. The subsequent application of a point source of heat to the film ignites a cationic ring‐opening frontal polymerization that emanates from that site and propagates to all portions of the irradiated sample. This article examines the impact of various molecular structural and experimental parameters on these novel hybrid frontal polymerizations that produce interpenetrating network polymers. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 4331–4340, 2007     

Letters to the Editor

The Mathematical Intelligencer encourages comments about the material in this issue. Letters to the editor should be sent to either of the editors-in-chief, Chandler Davis or Marjorie Senechal.     

Curcumin: A naturally occurring long‐wavelength photosensitizer for diaryliodonium salts

Curcumin, a naturally occurring, intensely yellow dye extracted from the spice turmeric, is an efficient photosensitizer for diaryliodonium salt photoinitiators at wavelengths ranging from 340 to 535 nm. With curcumin as a photosensitizer, it is possible to carry out the cationic photopolymerization of a wide variety of epoxide, oxetane, and vinyl monomers with long‐wavelength UV and visible light. An example of the photopolymerization of an epoxide monomer with ambient solar irradiation is provided. Several other curcumin analogues were synthesized, and their use as photosensitizers is examined. With such photosensitizers, the range of spectral sensitivity can be extended well into the visible region of the electromagnetic spectrum. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 5217–5231, 2005     

Degradative chain transfer in vinyl acetate polymerizations using toluene as solvent

In this work, we propose that retardation in vinyl acetate polymerization rate in the presence of toluene is due to degradative chain transfer. The transfer constant to toluene (C_trs) determined using the Mayo method is equal to 3.8 × 10^?3, which is remarkably similar to the value calculated from the rate data, assuming degradative chain transfer (2.7 × 10^?3). Simulations, including chain‐length‐dependent termination, were carried out to compare our degradative chain transfer model with experimental results. The conversion–time profiles showed excellent agreement between experiment and simulation. Good agreement was found for the M_n data as a function of conversion. The experimental and simulation data strongly support the postulate that degradative chain transfer is the dominant kinetic mechanism. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 3620–3625, 2007