Miscibility of bisphenol-A polycarbonate with poly(methyl methacrylate)

The miscibility of bisphenol-A polycarbonate (PC) with poly(methyl methacrylate) (PMMA) has been reexamined using differential scanning calorimetry (DSC) and optical indications for phase separation on heating, i.e., lower critical solution temperature (LCST) behavior. Various methods have been used to prepare the blends including methylene chloride (CH₂Cl₂) and tetrahydrofuran (THF) solution casting, melt mixing, and precipitation of PC and PMMA simultaneously from THF solution by using the nonsolvents methanol and heptane. It is shown that the resulting phase behavior for PC/PMMA blends is strongly affected by the blend preparation method. However, these blends are miscible over the whole blend composition range (unambiguous single composition-dependent T_g's and LCST behavior) when prepared by precipitation from solution using heptane as the nonsolvent. To the contrary, solution-cast and melt-mixed PC/PMMA blends were all phase separated, which may be attributed to the “solvent” effect and LCST behavior, respectively, not discovered in previous reports. Methanol precipitation does not lead to fully mixed blends, which demonstrates the importance of the choice of nonsolvent when using the precipitation method.     

Semi‐analytical integration of the 8‐node plane element stiffness matrix using symbolic computation

The semi‐analytical integration of an 8‐node plane strain finite element stiffness matrix is presented in this work. The element is assumed to be super‐parametric, having straight sides. Before carrying out the integration, the integral expressions are classified into several groups, thus avoiding duplication of calculations. Symbolic manipulation and integration is used to obtain the basic formulae to evaluate the stiffness matrix. Then, the resulting expressions are postprocessed, optimized, and simplified in order to reduce the computation time. Maple symbolic‐manipulation software was used to generate the closed expressions and to develop the corresponding Fortran code. Comparisons between semi‐analytical integration and numerical integration were made. It was demonstrated that semi‐analytical integration required less CPU time than conventional numerical integration (using Gaussian‐Legendre quadrature) to obtain the stiffness matrix. © 2005 Wiley Periodicals, Inc. Numer Methods Partial Differential Eq, 2006     

Conformational analysis of dipeptide‐derived polyisocyanides

The conformational properties of polymers derived from isocyanodipeptides have been investigated with a combination of model calculations, X‐ray diffraction, and circular dichroism spectroscopy. Depending on the configuration of the side chains, defined arrays of hydrogen bonds along the polymeric backbone are formed. This leads to a well‐defined conformation as, for example, expressed in the formation of lyotropic liquid‐crystalline phases and increased helical stability. Upon the disruption of the hydrogen bonds by a strong acid, a less well‐defined macromolecular conformation is observed. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 1725–1736, 2003     

A classical no-interaction theorem for bosonic strings and its quantum significance

We show that, in dimensions equal or greater than three, classical strings do not join or split. This is part of a no-interaction theorem that is also proved. The quantum theory is considered.     

Development of a quantitative FI-MS technique for the characterization of high- and nonboiling saturated hydrocarbon mixtures

Summary Using a saturated non-boiling hydrocarbon mixture, the influence of two parameters on the results of field ionization mass spectrometry (FI-MS) measurements was studied: (a) the potential difference between the FI emitter and the counterelectrode; (b) the emitter temperature.Variation of the potential difference had only a minor effect on the average molecular mass measured and had no evident effect on the relative ring number distribution in the sample. In contrast, when the emitter temperature was increased, higher average molecular masses were recorded. Moreover, the average molecular masses shifted to higher ring numbers. In order to control the relationship between the described influences during mixture analysis, measuring instructions have been developed that enable the quantitative analysis of unknown saturated samples. However, average molecular mass of the mixture must be known.

---

Entwicklung einer quantitativen FI-MS-Methode zur Charakterisierung von gesättigten hoch- und nichtsiedenden Kohlenwasserstoffgemischen

     

Investigation of multicomponent fluoride optical materials in the UV spectral region: I. Single crystals of Ca1−x R xF2+x (R = Sc, Y, La, Yb, Lu) solid solutions

Crystalline materials that are transparent in the vacuum UV spectral region and currently used have been reviewed. Transmission of crystals of solid solutions with the fluorite structure Ca_1?x R _xF_2+x (R = Sc, Y, La, Yb, Lu) in the UV and vacuum UV spectral regions has been investigated. It is shown that application of different methods of purification of fluorides from some impurities can significantly improve the optical quality of fluoride multicomponent crystals in the short-wavelength spectral region.     

Vascular morphology by three-dimensional magnetic resonance imaging

A three-dimensional examination of blood vessels is provided using MR data from seven cases. The vascular surfaces are constructed with an algorithm that automatically follows the selected artery or vein and generates a projected three-dimensional gradient shaded image. Fast 3DFT pulse sequences were optimized to enhance the time-of-flight contrast of the intravascular region. By increasing the surface threshold value in a three-dimensional head study, the flesh of a patient's face was peeled away to demonstrate the superfacial temporal artery. Gated cardiac images show the great vessels and cardiac chambers. A three-dimensional view of the aorta shows an irregular surface in the vicinity of an adrenal tumor. 3D MR exams provide a non-invasive technique for assessing vascular morphology in a clinical setting.     

Unsteady motion in single-line flow-injection systems

Unsteady motion in single-line flow-injection systems consisting of n tubular elements with valve or hydrodynamic injection is studied theoretically. A formula for the duration of the initial period of unsteady flow is derived. This initial period is much shorter than the mean residence time of the analyte in practical systems. It can therefore be neglected in mathematical modelling of such systems. Experimental data obtained with single-line systems with valve and hydrodynamic injection confirmed the validity of the theoretical equations.