Surface morphology at nanometer level and optical phase retardation of rubbed alignment films

The surface morphology of rubbed polyimide LC aligning films has been studied by scanning force microscopy. We examined three types of alignment film: HT-210, AL-1051 (main chain type) and AL-8044 (side chain type) polyimide surfaces. The rubbed polyimide surfaces show anisotropic alignment of the polymer chain cluster, and a microgroove between the ripple pattern streaks. Also, they are periodically oriented along the rubbing direction. The optical phase retardation of the rubbed surface does not increase with increased cumulative time of rubbing, On the other hand, it increases monotonically with increasing rubbing depth.     

Zigzag defect-free alignment of surface stabilized ferroelectric liquid crystal cells with a polyimide irradiated by polarized UV light

Zigzag defect-free surface stabilized ferroelectric liquid crystal (SSFLC) cells were prepared using a photodegradable polyimide (PI) having a cyclobutane ring in the backbone. The PI layers were irradiated by polarized ultraviolet light (PUVL) at normal incidence to the surface, and characterized by UV and FTIR spectroscopy. The anisotropy originates from preferential cleavage of PI chains oriented parallel to the polarization direction of the irradiating PUVL. After the polarized UV light irradiation, the PI surface was much flatter than that after rubbing, but it induced a similar order parameter of dye-doped nematic LC molecules to that for a rubbed cell. Alignment of both the FLC molecules and the layer structure is important in SSFLC. After 40 min irradiation, the FLC molecules were well aligned homogeneously, and the FLC cells showed a uniform texture without zigzag defects which also indicates a well aligned layer structure. Zigzag defect-free alignment may result from the flatter surface, the much smaller and more constant pretilt angles, and the bigger cone angle than those achieved by rubbing.     

Dimesogenic liquid crystal consisting of cholesterol and Schiff base moieties: dependence of LC properties on the spacer length and fluorination of the alkoxy tails

The liquid crystalline properties of two series of non‐symmetric liquid crystal dimers consisting of cholesterol and Schiff base moieties interconnected by ω‐oxyalkanoyl spacers of varying length are compared: one series (SBOC‐ n ) carry the octyloxy tail on the Schiff base mesogen, and the other (SBOF‐ n ) a perfluoroheptylmethyloxy tail. In general, compounds with the fluorinated alkoxy tail exhibited mesophases over a much wider temperature range than those with the alkoxy tail. The latter series favoured the formation of more diverse mesophases than the former. SBOC‐4, ‐5 and ‐7, and SBOF‐4, ‐5 and ‐10 formed the chiral smectic C phase.     

Synthesis and characterisation of photopolymerisable liquid crystals based on the π-extended fluorene core and their corresponding non-reactive analogues

We have synthesised a series of new reactive mesogens with photopolymerisable di-acrylates and their corresponding non-reactive analogues based on the π-conjugated aromatic core, fluorene (F)-di-[thiophene (T)-benzene (B)], using the Stille and Suzuki coupling reaction. The effect of lateral alkyl chains on the 9-position of the central fluorene moiety as well as α, ω- side alkyl chains attached to the π-conjugated aromatic core on the mesomorphism was investigated by utilising differential scanning calorimetry (DSC) and polarising optical microscopy (POM). A wide angle X-ray scattering (WAXS) study at the various temperatures was also carried out to reveal phase structures. Photopolymerisable di-acrylates connected directly to the rigid aromatic core showed higher phase transition temperatures, probably due to the induced dipole moment in comparison with those of a non-reactive methyl–ether counterpart.     

Sigmatropic Rearrangements in Phosphorylated 2-Azaallylic Systems

Abstract

Allylic and heteroallylic compounds are classical objects of organic chemistry and can serve as models in the investigation of various theoretical problems. The anions and 1,3-dipoles generated from azaallylic derivatives are widely used in the synthesis of cyclic and acyclic nitrogen-containing compounds.     

Electrochemical properties of PEO/PMMA blend-based polymer electrolytes using imidazolium salt-supported silica as a filler

In this study, the composite polymer electrolytes (CPEs) were prepared by solution casting technique. The CPEs consisted of PEO/PMMA blend as a host matrix doped with LiClO₄. Propylene carbonate (PC) was used as plasticizer and a small amount of imidazolium salt-supported amorphous silica (IS-AS) as a filler was prepared by the sol–gel method. At room temperature, the highest conductivity was obtained for the composition having PEO–PMMA–LiClO₄–PC–4wt. % IS-AS with a value of 1.15 × 10^?4 S/cm. In particular, the CPE using the IS-AS filler showed a higher conductivity than any other sample (fumed silica, amorphous silica). Studies of differential scanning calorimetry and scanning electron microscopy indicated that the ionic conductivity increase was due to an expansion in the amorphous phase which enhances the flexibility of polymeric chains and the homogeneous structure of CPEs. It was found that the ionic conductivity and interfacial resistance stability of CPEs was significantly improved by the addition of IS-AS. In other words, the resistance stability and maximum ambient ionic conductivity of CPEs containing IS-AS filler were better than CPEs containing any other filler.     

Chip-based nLC-TOF-MS is a highly stable technology for large-scale high-throughput analyses

Many studies focused on the discovery of novel biomarkers for the diagnosis and treatment of disease states are facilitated by mass spectrometry-based technology. HPLC coupled to mass spectrometry is widely used; miniaturization of this technique using nano-liquid chromatography (LC)-mass spectrometry (MS) usually results in better sensitivity, but is associated with limited repeatability. The recent introduction of chip-based technology has significantly improved the stability of nano-LC-MS, but no substantial studies to verify this have been performed. To evaluate the temporal repeatability of chip-based nano-LC-MS analyses, N-glycans released from a serum sample were repeatedly analyzed using nLC-PGC-chip-TOF-MS on three non-consecutive days. With an average inter-day coefficient of variation of 4 %, determined on log₁₀-transformed integrals, the repeatability of the system is very high. Overall, chip-based nano-LC-MS appears to be a highly stable technology, which is suitable for the profiling of large numbers of clinical samples for biomarker discovery.     

Structural and electrical properties of chemical solution deposited (Bi0.9Tb0.1)(Fe0.975 TM 0.025)O3±δ (TM = Ni, Mn and Ti) thin films

Effects of Tb and transition metal (TM = Ni, Mn and Ti) ions co-doping on the structural, electrical and ferroelectric properties of the BiFeO₃ thin films prepared by using a chemical solution deposition method were reported. From X-ray diffraction and Raman scattering analyses, distorted rhombohedral perovskite structures were observed for all thin films. Improved electrical and ferroelectric properties were observed for the co-doped thin films. Among the thin films, the lowest leakage current density of 2.67 × 10^?6 A/cm² (at 100 kV/cm), large remnant polarization (2P _r ) of 82.2 μC/cm² and low coercive field (2E_c) of 680 kV/cm (at 1,036 kV/cm) were measured for the (Tb, Mn) co-doped thin film.     

Complexation of hydrazine with native cellulose in water and toluene

Adsorption–complexation of cellulose by hydrazine solutions in water and toluene was studied for native cellulose of varied crystallinity. Penetration of hydrazine into cellulose takes place more readily in hydrazine solution of higher concentration and with cellulose of lower crystallinity, but the equilibrium uptake was nearly independent of crystallinity. Complexation from toluene solution takes place at lower hydrazine concentration in toluene than in water, presumably because of the difference in hydrazine–solvent interaction. The adsorption isotherm of hydrazine in water is likely to be sigmoid, implying a cooperative sorption mechanism. It can presumably be ascribed to the disordered structure in the course of complexation.     

Recent developments in polymer–block–polypeptide and protein–polymer bioconjugate hybrid materials

In the last few years, polymer bioconjugates have been shown to be useful in many emerging areas of materials science. Consequently, the synthesis of polymer bioconjugates has suddenly become a central topic in polymer chemistry. The versatility and robust nature of modern synthetic methods such as controlled radical polymerisation (CLRP),¹ ring-opening polymerisation (ROP), and ‘click’ chemistry make them excellent tools for the preparation of tailor-made polymer bioconjugates. CLRP in combination with other techniques has been shown to be a mature technology for building tailor-made block copolymers and protein–polymer conjugates with a wide range of applications, especially in biomedical domains. This review describes the recent advances and progress in the rapidly expanding field of bioconjugation, outlining the work performed up to 2012.