Investigation of sulfonated poly(ether ether ketone sulfone)/heteropolyacid composite membranes for high temperature fuel cell applications

The sulfonated poly(ether ether ketone sulfone) (SPEEKS)/heteropolyacid (HPA) composite membranes with different HPA content in SPEEKS copolymers matrix with different degree of sulfonation (DS) were investigated for high temperature proton exchange membrane fuel cells. Composite membranes were characterized by Fourier transfer infrared spectroscopy (FTIR) and scanning electron microscopy (SEM). FTIR band shifts suggested that the sulfonic acid groups on the copolymer backbone strongly interact with HPA particles. SEM pictures showed that the HPA particles were uniformly distributed throughout the SPEEKS membranes matrix and particle sizes decreased with the increment of copolymers' DS. The holes were not found in SPEEKS‐4/HPA30 (consisting of 70% SPEEKS copolymers with DS = 0.8 and 30% HPA) composite membrane after composite membranes were treated with boiling water for 24 h. Thermal stabilities of the composite membranes were better than those of pure sulfonated copolymers membranes. Although the composite membranes possessed lower water uptake, it exhibited higher proton conductivity for SPEEKS‐4/HPA30 especially at high temperature (above 100 °C). Its proton conductivity linearly increased from 0.068 S/cm at 25 °C to 0.095 S/cm at 120 °C, which was higher than 0.06 S/cm of Nafion 117. In contrast, proton conductivity of pure SPEEKS‐4 membrane only increased from 0.062 S/cm at 25 °C to 0.078 S/cm at 80 °C. At 120 °C, proton conductivity decreased to poor 0.073 S/cm. The result indicated that composite membranes exhibited high proton conductivity at high temperature. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 1967–1978, 2006     

Preparation and characterization of rigid poly(vinyl chloride)/MMT nanocomposites. II. XRD,morphological and mechanical characteristics

A Haake torque rheometer equipped with an internal mixer is used to study the influence of the amount of sodium montmorillonite (Na⁺‐MMT) and organically modified MMT (O‐MMT) on X‐ray diffraction (XRD), morphology, and mechanical characteristics of rigid poly (vinyl chloride) (PVC)/Na⁺‐MMT and PVC/O‐MMT nanocomposites, respectively. Results of XRD and transmission electron microscopy (TEM) indicate that MMT is partially encapsulated and intercalated in the rigid PVC/Na⁺‐MMT nanocomposites. However, results of XRD and TEM show MMT is partially intercalated and exfoliated in the rigid PVC/O‐MMT nanocomposites. Tensile strength, yield strength, and elongation at break of the rigid PVC/MMT nanocomposites were improved simultaneously with adding 1–3 wt % Na⁺‐MMT or O‐MMT with respect to that of pristine PVC. However, the addition of Na⁺‐MMT or O‐MMT should be kept as not more than 3 wt % to optimize the mechanical properties and the processing stability of the rigid PVC/MMT nanocomposites. SEM micrographs of the fractured surfaces of the rigid PVC/Na⁺‐MMT and PVC/O‐MMT nanocomposites both before and after tensile tests were also illustrated and compared. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 2145–2154, 2006     

4-Amino-imidazole durchThorpe-Cyclisierung

The alkylation of arylaminomethylenecyanamides1 or cyano-imidothiocarbamates2 with -halogen carbonyl compounds followed by base catalysed cyclization yields substituted 4-amino-imidazoles4. Imidazo[4,5-d]pyrimidones5, 6 and imidazo[4,5-b]pyridines7 can be obtained from4.     

The electrocapillarity of polyacrylates

Summary The electrocapillary properties of polyacrylic acid have been studied by two methods. Exploratory measurements have been made of the effect of the polymer on the differential capacity of a mercury drop in 0.1 m sodium perchlorate. They showed that the polymer was strongly adsorbed over a wide range of potentials but that it did not appear to form a monolayer. The surface excess of polymer obtained from drop weight data showed a maximum at very low concentrations and then a decline at higher concentrations. The bulk of the work was carried out by making surface tension measurements, using a sessile mercury drop, in solutions of a fraction of polyacrylic acid (mol. wt. 7.02×10⁴) in potassium chloride at 0.01, 0.1, 0.2, and 0.5 m at 25°C.The data have been used to evaluate the surface excesses of the polymer and of the inorganic ions. The distribution of K⁺ and Cl^– in the electrical double layer and the contact adsorption of Cl^– on the mercury were very little affected by the presence of the polymer. The surface excess of polymer was always found to be greatest at low concentrations, to decrease steeply at first as the concentration was increased and then to decrease more slowly at higher concentrations.Possible explanations of this behaviour are discussed and it is concluded that the rapid decrease is a consequence of molecular weight dispersion and the stronger adsorption of high molecular weight polymer. The slow decrease in surface excess at higher concentrations may be a result of configurational changes of the polymer molecules.Surface pressure data show that, despite this decrease in the surface excess, the surface coverage reaches a high level at very low polymer concentrations and then continues to increase slowly as the concentration of polymer is increased. This apparent contradiction is due to changes in configuration of the adsorbed polymer molecules. At higher bulk concentrations the chain configurations are more compact and each adsorbed molecule makes more contacts with and so occupies a greater area of the mercury surface than at low concentrations.The conclusion is reached that the surface excess of polymer is mostly contained in a layer probably more than 1000 Å thick. It consists of a concentrated and entangled mass of polymer chains. Relatively few of these chains are in contact with the mercury at any istant. The concentration in this surface layer decreases steadily with increasing distance from the mercury surface and it merges without discontinuity into the bulk solution.With 10 figures in 22 details     

Stereochemie von Metallocenen, 40. Mitt.

Starting from optically active methylferrocene-- and--carboxylic acids (1 a and1 b) of known absolute configuration and enantiomeric purity about 15 chiral ferrocenes (of each isomeric series— and ) were obtained by suitable ligand transformations. Thereby (almost) all possible chiral combinations of the ligands CH₃, COOH (COO^–), COOCH₃, CN and NH₂ (NH₃ ⁺) were accessible which are necessary for a potential test of approximations of chirality functions for compounds with basic symmetry C_5v. The chiroptical properties of these disubstituted ferrocenes are recorded.Preliminary tests using a shortened Ansatz revealed large discrepancies between calculated () and found [M]_D-values. Possible reasons for this failure are discussed.

---

---

61. Mitt. über Ferrocenderivate

---

39. Mitt.:A. Meyer, H. Neudeck undK. Schlögl, Chem. Ber.110, 1403 (1977).

---

60. Mitt.:V. Rapi, K. Schlögl undB. Steinitz, J. Organometal. Chem.94, 87 (1975).     

Neue Wege der Analytik durch Kombination der direkten quantitativen Dünnschicht-Chromatographie mit elektronischer Datenverarbeitung

A computer program for direct evaluation of thin-layer chromatograms, which already was described earlier [3] has been tested with a laboratory and some technical formulations of a pesticide. Results have been compared with those obtained by two conventional methods. Mean relative standard deviation calculated from results compiled by electronic data processing (method A) is about 6%, compared to 10% received by graphic method (method C) which is employed by most investigators. In addition, overall time of analysis is 34% higher if graphic method is used. Method A saves time and expense especially in routine analysis because working of the process is easier and may be performed even by assistent personal. The proposed method is suitable for the determination of different active ingredients and impurities even in difficult technical products.     

Zur Kenntnis von Natrium-hexafluoromanganat(III)

Sodium hexafluoromanganate(III) has been synthesized by heating equimolecular quantities of Na₂MnF₅ and NaF in argon atmosphere. The compound is monoclinic witha=5.56 (1) Å,b=5.84 (1) Å,c=8.10 (2) Å, =90.7 (2) andZ=2. It is a high spin complex with _eff and the deformation of the octahedra is evident from its IR-spectra. Two enantiotropic transitions (at 562 and 653°C) and the melting point at 800°C have been observed.

---

---

8. Mitt.: Mh. Chem.106, 483 (1975).     

Discussion on the method for the measurement of the flexural modulus of coupled materials and reasons of the shifts of theQ −1 maxima caused by coupling

Summary When measuringQ ^–1 and the flexural resonance frequency of bars clamped at one end, constituted by a viscoelastic polymeric material glued to a rigid support of modulusE ₁, it is possible to calculate the componentsE ₂ andE ₂ of the complex elastic modulus of the polymeric material examined. In this work the minimum (critical) value of the ratioa=E ₂ /E ₁=a _c and the values of the ratioQ ₂ ^–1/Q ^–1=F ₁ are evaluated beyond which no exact calculation ofE ₂ and ofQ ₂ ^–1 is possible.Within the confidence limits of the linear viscoelasticity theory, these values depend on the accuracy of measurement of both frequency and resonance curve, as well as on the instrument employed, on the operating temperature and on the ratio between the thicknesses of the two coupled materials.In order to keep outside the critical conditions, the most convenient method involves the use of measurements of coupled test-pieces having different ratiosz between their thicknesses and of supports having different modulusE ₁, depending on the field of temperature of the analysis ofE ₂ and tg ₂ concerning and E.P.R. elastomer and a vulcanized cis-1,4 polyisoprene in very wide ranges of temperature comprising the glass transition. Moreover, it is demonstrated by analysis the shift on the temperature axis of the tg maximum of the composite test-piece with respect to the position of the tg maximum of the polymeric material alone.With 11 figures and 1 table