Implementation of some higher-order convection schemes on non-uniform grids

A generalized formulation is applied to implement the quadratic upstream interpolation (QUICK) scheme, the second-order upwind (SOU) scheme and the second-order hybrid scheme (SHYBRID) on non-uniform grids. The implementation method is simple. The accuracy and efficiency of these higher-order schemes on non-uniform grids are assessed. Three well-known bench mark convection-diffusion problems and a fluid flow problem are revisited using non-uniform grids. These are: (1) transport of a scalar tracer by a uniform velocity field; (2) heat transport in a recirculating flow; (3) two-dimensional non-linear Burgers equations; and (4) a two-dimensional incompressible Navier-Stokes flow which is similar to the classical lid-driven cavity flow. The known exact solutions of the last three problems make it possible to thoroughly evaluate accuracies of various uniform and non-uniform grids. Higher accuracy is obtained for fewer grid points on non-uniform grids. The order of accuracy of the examined schemes is maintained for some tested problems if the distribution of non-uniform grid points is properly chosen.     

Anchoring Properties of Nematic Liquid Crystals Studied Using the Attenuated Total Reflection Method

By using the attenuated total reflection method associated with the excitation of surface plasmons, the tilt angle of the liquid crystal director and its gradient at the surface are measured in a planar nematic cell as a function of the applied voltage. The surface anchoring anisotropy δπ of the liquid crystal and the surface elastic constant k_s, are found to be δπ = 0.288 erg/cm and k_s, = 9·12 × 10^-11 erg, respectively, when the boundary condition suggested by Barbero et al is used. The theoretical and experimental values obtained with this boundary condition and that of Mada are discussed. The results show that the boundary condition proposed by Barbero et al is in better agreement with the experiment.     

Bioaccumulation and excretion of arsenic compounds by a marine unicellular alga,polyphysa peniculus

Polyphysa peniculus was grown in artificial seawater in the presence of arsenate, arsenite, monomethylarsonate and dimethylarsinic acid. The separation and identification of some of the arsenic species produced in the cells as well as in the growth medium were achieved by using hydride generation–gas chromatography–atomic absorption spectrometry methodology. Arsenite and dimethylarsinate were detected following incubation with arsenate. When the alga was treated with arsenite, dimethylarsinate was the major metabolite in the cells and in the growth medium; trace amounts of monomethylarsonate were also detected in the cells. With monomethylarsonate as a substrate, the metabolite is dimethylarsinate. Polyphysa peniculus did not metabolize dimethylarsinic acid when it was used as a substrate. Significant amounts of more complex arsenic species, such as arsenosungars, were not observed in the cells or medium on the evidence of flow injection–microwave digestion–hydride generation–atomic absorption spectrometry methodology. Transfer of the exposed cells to fresh medium caused release of most cell–associated arsenicals to the surrounding environment.     

A note on an SOR-like method for augmented systems

Golub et al. (2001, BIT, 41, 71–85) gave a generalizedsuccessive over-relaxation method for the augmented systems.In this paper, the connection between the SOR-like method andthe preconditioned conjugate gradient (PCG) method for the augmentedsystems is investigated. It is shown that the PCG method isat least as accurate (fast) as the SOR-like method. Numericalexamples demonstrate that the PCG method is much faster thanthe SOR-like method.     

氘－氚聚变等离子体中高能α粒子的诊断

本文对于用电荷交换方法或低杂波涨落的方法测量高能α粒子作了简短的评述，建议用核反应１３Ｃ（α，ｎ）１６Ｏ测量氘－氚聚变等离子体中的高能α粒子，并提出了一种减少杂质污染，增加穿透深度的方法。     

Formation of β‐iPP in isotactic polypropylene/ethylene–propylene rubber blends: Effects of preparation method,composition, and thermal condition

The effects of preparation method, composition, and thermal condition on formation of β‐iPP in isotactic polypropylene/ethylene–propylene rubber (iPP/EPR) blends were studied using modulated differential scanning calorimeter (MDSC), wide angle X‐ray diffraction (WAXD), and phase contrast microscopy (PCM). It was found that the α‐iPP and β‐iPP can simultaneity form in the melt‐blended samples, whereas only α‐iPP exists in the solution‐blended samples. The results show that the formation of β‐iPP in the melt‐blended samples is related to the crystallization temperature and the β‐iPP generally diminishes and finally vanishes when the crystallization temperature moves far from 125 °C. The phenomena that the lower critical temperature of β‐iPP in iPP/EPR obviously increases to 114 °C and the upper critical temperature decreases to 134 °C indicate the narrowing of temperature interval, facilitating the formation of β‐iPP in iPP/EPR. Furthermore, it was found that the amount of β‐iPP in melt‐blended iPP/EPR samples is dependent on the composition and the maximum amount of β‐iPP formed when the composition of iPP/EPR blends is 85:15 in weight. The results through examining the effect of annealing for iPP/EPR samples at melt state indicate that this annealing may eliminate the susceptibility to β‐crystallization of iPP. However, only α‐iPP can be observed in solution‐blended samples subjected to annealing for different time. The PCM images demonstrate that an obvious phase‐separation happens in both melt‐blended and solution‐blended iPP/EPR samples, implying that compared with the disperse degree of EPR in iPP, the preparation method plays a dominant role in formation of β‐iPP. It is suggested that the origin of formation of β‐iPP results from the thermomechanical history of the EPR component in iPP/EPR. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 1704–1712, 2007     

Operator‐splitting method for the analysis of cavitation in liquid‐lubricated herringbone grooved journal bearings

This paper presents an operator‐splitting method (OSM) for the solution of the universal Reynolds equation. Jakobsson–Floberg–Olsson (JFO) pressure conditions are used to study cavitation in liquid‐lubricated journal bearings. The shear flow component of the oil film is first solved by a modified upwind finite difference method. The solution of the pressure gradient flow component is computed by the Galerkin finite element method. Present OSM solutions for slider bearings are in good agreement with available analytical and experimental results. OSM is then applied to herringbone grooved journal bearings. The film pressure, cavitation areas, load capacity and attitude angle are obtained with JFO pressure conditions. The calculated load capacities are in agreement with available experimental data. However, a detailed comparison of the present results with those predicted using Reynolds pressure conditions shows some differences. The numerical results showed that the load capacity and the critical mass of the journal (linear stability indicator) are higher and the attitude angle is lower than those predicted by Reynolds pressure conditions for cases of high eccentricities. Copyright © 2004 John Wiley & Sons, Ltd.     

Numerical analysis of the rotating viscous flow approaching a solid sphere

A numerical simulation is performed to investigate the flow induced by a sphere moving along the axis of a rotating cylindrical container filled with the viscous fluid. Three‐dimensional incompressible Navier–Stokes equations are solved using a finite element method. The objective of this study is to examine the feature of waves generated by the Coriolis force at moderate Rossby numbers and that to what extent the Taylor–Proudman theorem is valid for the viscous rotating flow at small Rossby number and large Reynolds number. Calculations have been undertaken at the Rossby numbers (R_o) of 1 and 0.02 and the Reynolds numbers (R_e) of 200 and 500. When R_o=O(1), inertia waves are exhibited in the rotating flow past a sphere. The effects of the Reynolds number and the ratio of the radius of the sphere and that of the rotating cylinder on the flow structure are examined. When R_o ? 1, as predicted by the Taylor–Proudman theorem for inviscid flow, the so‐called ‘Taylor column’ is also generated in the viscous fluid flow after an evolutionary course of vortical flow structures. The initial evolution and final formation of the ‘Taylor column’ are exhibited. According to the present calculation, it has been verified that major theoretical statement about the rotating flow of the inviscid fluid may still approximately predict the rotating flow structure of the viscous fluid in a certain regime of the Reynolds number. Copyright © 2004 John Wiley & Sons, Ltd.     

Damage and fracture evaluation of granular composite materials by digital image correlation method

This paper presents the applications of digital image correlation technique to the mesoscopic damage and fracture study of some granular based composite materials including steelfiber reinforced concrete, sandstone and crystal-polymer composite. The deformation fields of the composite materials resulted from stress localization were obtained by the correlation computation of the surface images with loading steps and thus the related damage prediction and fracture parameters were evaluated. The correlation searching could be performed either directly based on the gray levels of the digital images or from the wavelet transform (WT) coefficients of the transform spectrum. The latter was developed by the authors and showed higher resolution and sensitivity to the singularity detection. Because the displacement components came from the rough surfaces of the composite materials without any coats of gratings or fringes of optical interferometry, both surface profiles and the deformation fields of the composites were visualized which was helpful to compare each other to analyze the damage of those heterogeneous materials. The project supported by the National Natural Science Foundation of China (10125211 and 10072002), the Scientific Committee of Yunnan Province for the Program of Steel Fiber Reinforced Concrete, and the Institute of Chemical Materials, CAEP at Mianyang