双螺旋叠栅条纹检测光束准直性的两种方法

介绍双螺旋叠栅条纹检测光束准直性的基本原理,进一步就双螺旋叠栅条纹的特征参量与被测光束发散角(即光束准直精度)的关系进行分析和推导。在分析双螺旋叠栅条纹进行时,首先采用频域低通滤波提取纯叠栅条纹,然后提取纯叠栅条纹的特征参量。提出两种特征参量的提取方法,一种依次进行傅里叶变换计算相位信息的傅里叶变换方法,另一种是受传统时间相移算法启发而提出的空间相移算法,讨论了在两种方法中极坐标的重采样问题和相应的计算公式,并进行了计算机模拟。结果表明,傅里叶变换方法和空间相移算法实质都是获取叠栅条纹全场趋势的平均值,使最终光束发散角的检测具有很高的精度,对自成像条纹周期的检测误差在±2.8‰以内。     

LaMgAl11O19:Co2+被动调Q铒玻璃激光器研究

综述了被动调Q铒玻璃激光器的发展概况,推导了被动调Q铒玻璃激光器输出脉冲能量、脉宽的解析表达式,数值模拟了腔内损耗与输出脉冲能量、脉宽及峰值功率的关系以及输出脉冲能量与输入抽运能量的关系.设计了一台LaMgAl11O19:Co2 被动调Q铒玻璃激光器,实验验证了数值模拟分析结果.结果表明,腔内损耗增加将导致输出脉冲能量下降,脉宽变大,从而峰值功率降低.输入能量低于12 J时,输出只有单脉冲,当输入能量大于12 J时,输出会出现双脉冲.在8 J的电输入下,获得了峰值功率50 kW,2.7 mJ的1.535 tm激光输出.最后讨论了提高单脉冲能量的方法.     

基于微机电系统光栅平动式光调制器实验和优化设计

基于微机电系统(MEMS)的光栅平动式光调制器(光栅平动式光调制器)调制性能的实验研究关系到其进一步应用。设计了光栅平动式光调制器的相干光学信息处理系统实验方案,He-Ne激光器出射的光束经扩束器和准直透射后成为平行光入射光栅平动式光调制器,被测光栅平动式光调制器放置在相干光学信息处理系统的输入面,滤波器在频谱面上,显微镜放大像面上的信号,经CCD在计算机上记录存储;实验结果和理论分析吻合。对光栅平动式光调制器进行方案优化,将可动光栅边框和悬臂梁表面处理成不反光,使可动光栅和下反射镜构成的整个反射面为光栅周期的整数倍。经理论计算,在光栅周期为8μm,光栅占空比为0.5,光栅边距为2μm,周期数为6的条件下,光栅平动式光调制器图像填充率为74.67%,光学效率为81.06%,衬比度大于5000∶1。     

可调谐二极管激光吸收光谱法测量气体温度

研究了一种新型的非接触式测温技术——可调谐二极管激光吸收光谱(TDLAS)测温技术。介绍了温度测量及调制吸收光谱技术原理,分析了调制幅度对气体温度测量的影响。优选了氧气吸收谱线对13163.78 cm-1和13164.18 cm-1,在搭建的高温实验系统上,实现了气体温度和浓度的同时测量。通过分析实测波形获得了谱线13164.18 cm-1在823~1323 K温度范围内的碰撞展宽系数和温度指数。实验结果表明,在823~1323 K温度范围内,系统温度测量的线性误差为0.65%,最大波动为±15 K。     

双染料敏化光致聚合物的光化动力学研究

研究了光致聚合物的光化学反应理论模型及其动力学参量。合成了染料藻红B和亚甲基蓝作为联合光敏剂共同敏化的全息光存储光致聚合物材料。对材料测试分别得到在曝光波长为633 nm与曝光强度为65 mW/cm2时,透射率随曝光条件的变化关系以及材料各光化学参量。结果表明,随着曝光波长与曝光强度的增加,光致聚合物的光化漂白速率常数k与量子产率Φ增大,当曝光强度为65 mW/cm2时透射率在短波长下出现了下降,光化漂白速率常数k出现负值,而摩尔吸收系数ε在条件不同时则表现了不同的变化趋势。     

用于显示的透射型法布里-珀罗光调制器

提出了一种用于显示的,基于透射型法布里-珀罗干涉的微机电系统(MEMS)光学调制器。基于多光束干涉原理分析了调制器的光学特性,推导出了调制器结构的特征参量。分析表明,当调制器的腔长为cλ/4时,透射光可以实现暗态显示;当调制器的腔长取为零或cλ/2时,透射光可以实现亮态显示。通过控制法布里-珀罗腔长,就可实现调制器的明暗调制。理论上证明了该调制器用于显示的可行性。设计了一种基于微机电系统的透射型法布里-珀罗光学调制器结构,该调制器的理论衬比度达到150。仿真结果表明,该调制器具有2.4 V的低电压静电驱动性能。     

Experimental and Numerical Investigation on Strain Rate-Dependent Tensile Behavior of ZrB2–SiC Ceramic Composite

In this study,the strain rate-dependent dynamic tensile behavior of ZrB2-20%SiC ceramic composite was investigated using experimental and numerical approaches.The split Hopkinson pressure bar apparatus was used to measure the dynamic splitting tensile response at strain rates of 17-67 s^?1.The experiment results demonstrate a significant strain rate dependence of the dynamic tensile behavior of the ZrB2-SiC ceramic composite.The dynamic tensile strength increased linearly with the strain rate,from 288 MPa at 17 s^?1to 654 MPa at 67 s^?1.Moreover,a strain rate-dependent tensile strength was introduced into a modified JH-2 model to describe the dynamic tensile behavior and fracture process of ZrB2-SiC ceramics.The numerical results of dynamic tensile strength agree well with the experimental result.Moreover,the fracture process of ZrB2-SiC ceramics under dynamic tension was further studied by combining high-speed images and numerical results.The effect of strain rate on the fracture process and failure patterns of the ZrB2-SiC ceramic composite could be verified by the modified JH-2 model.     

Potential Value of Wood Tar as a Natural Fungicide against Valsa mali

The Valsa canker caused by Valsa mali seriously harmed the production of East Asian apples and caused very significant economic losses. Considering the chemical residues and the improvement of people’s awareness of environmental protection, there is a need for screening new green pesticides for the control of Valsa canker. Therefore, we conducted systematic evaluations on the antifungal activity of wood tar. In this research, the effective concentration (EC₅₀) of six strains of V. mali to wood tar was determined, and the EC₅₀ ranged from 69.54 to 92.81 μg/mL. After treatment with wood tar, the hyphae of V. mali broke, swelled, and deformed; the permeability of the cell membrane increased; and the activity of pectinase reduced. Moreover, the expression levels of five genes related to pectinase also decreased significantly. In addition, the activities of phenylalanine ammonia lyase (PAL) and peroxidase (POD) of apple leaves treated with wood tar also increased. On detached apple branches, wood tar also showed therapeutic and protective activities. In the 2016–2019 field experiments, wood tar also showed good efficacy against Valsa canker and promoted the formation of callus. (In the experiments from 2016 to 2019, it can be seen that the control effect of 50% wood tar and 100% wood tar in the field is above 75% and promoted the formation of callus.) This study is the first to report the bidirectional efficacy of wood tar against Valsa mali and for trunk wound healing. The above results evidenced that wood tar has great potential to be developed as a natural alternative to commercial fungicides for the management of apple Valsa canker.