Temperature dependent exchange bias effect in polycrystalline BiFeO3/FM (FM = NiFe, Co) bilayers

Extensive studies on the temperature (T) dependent exchange bias effect were carried out in polycrystalline BiFeO₃(BFO)/NiFe and BFO/Co bilayers. In contrast to single-crystalline BFO/ferromagnet (FM) bilayers, sharp increase of the exchange bias field (H _E ) below 50 K were clearly observed in both of these two bilayers. However, when T is higher than 50 K, H _E increases with T and decreases further when T is larger than 230 K (for BFO/NiFe) or 200 K (for BFO/Co), which is similar to those reported in single-crystalline BFO/FM bilayers. After the exploration of magnetic field cooling, the temperature dependent exchange bias can be explained considering two contributions from both the interfacial spin-glass-like frustrated spins and the polycrystalline grains in the BFO layer. Moreover, obvious exchange bias training effect can be observed at both 5 K and room temperature and the corresponding results can be well fitted based on a recently proposed theoretical model taking into account the energy dissipation of the AFM layer.     

多孔介质两相流的局部守恒有限元分析

用局部守恒有限元法研究多孔介质两相渗流问题.详细阐述局部守恒有限元法的基本原理,推导两相渗流问题的局部守恒有限元计算格式并编制相应的计算程序.通过一维Buckley-Leverett两相渗流算例验证该方法的正确性.应用局部守恒有限元法和混合有限元法分别对2个模型进行分析对比.计算结果表明局部守恒有限元法具有良好的鲁棒性及适用性,相较于混合有限元法,处理过程简单,计算时间缩短,为标准有限元法应用于复杂渗流问题提供了一种途径.     

谈谈静电实验

对静电实验中常见的漏电现象、绝缘材料的选取、摩擦起电等问题进行了探讨。     

DA-16晶体管毫伏表元件特性变异所致软故障分析

本文介绍了晶体元件特性参数变异所致软故障分析判断。     

烟气中Hg的氧化机理的研究

本文对Ｈｇ与Ｃｌ２在烟气中的氧化反应进行了热力平衡计算和动力学计算。平衡计算的结果表明有ＣＩ元索存在时Ｈｇ的氧化率为１００％，而在相同的条件下动力学计算纺果为Ｈｇ的氧化率在２０％～８０％之间变化，与实验结果吻合。实际的氧化反应是一种超平衡状态，不能达到理想的平衡状态。因此应采用动力学与热力平衡分析相结合的方法研究Ｈｇ在烟气中的反应机理。同时，计算结果显示Ｃｌ含量对Ｈｇ的氧化率的影响很大．     

工作点测量系统在合肥光源的应用研究

 介绍了利用合肥光源(HLS)的工作点测量系统进行一些束流参数的测量及其应用研究，这些参数包括工作点、β函数；自然色品以及中心频率。同时还进行了清洗电极对工作点的影响的测量。给出了一些测量结果，测量结果与理论计算值相当吻合。     

A Silicon Nanowire‐Based Electrochemical Sensor with High Sensitivity and Electrocatalytic Activity

A new kind of silicon nanowire (SiNWs)‐based nanoelectrode assembly, a gold‐nanoparticle‐decorated silicon nanowire array (AuNPs@SiNWsAr), is employed for the construction of high‐performance electrochemical sensors. Significantly, the electrochemical nanosensors are capable of sensitive detection of various electroactive molecules (e.g., dopamine (DA), ascorbic acid (AA), hydrogen peroxide (H₂O₂), and glucose). Further, DA molecules loaded on the surface of AuNPs@SiNWsAr preserve stable high electroactivity overnight without special protection, while free DA molecules may lose their biological activity due to severe oxidization in ambient environment. These findings may offer new opportunities for the design of high‐performance electrochemical nanosensors with high sensitivity and robust stability.     

Trace analysis of polycyclic aromatic hydrocarbons using calixarene layered gold colloid film as substrates for surface‐enhanced Raman scattering

A surface‐enhanced Raman scattering (SERS) active substrate for the detection of polycyclic aromatic hydrocarbons (PAHs) was developed, which used 25, 27‐dimercaptoacetic acid‐26, 28‐dihydroxy‐4‐terbutyl calix[4]arene (DMCX) to functionalize a gold colloid film. This SERS‐active substrate prepared by self‐assembly method exhibits a high sensitivity, especially for the detection of PAHs. With the use of this SERS‐active substrate and with the application of the shifted excitation Raman difference spectroscopy (SERDS) technique, Raman signals of pyrene and anthracene in aqueous solutions at low concentration level (500 pM) can be obtained. Moreover, because PAHs are blocked from being directly adsorbed on gold colloid by DMCX and the photochemical reactions of adsorbates are avoided, the Raman bands of PAHs adsorbed on DMCX‐fuctionalized gold colloid film can be one‐to‐one correspondence with those of solid PAHs, and additionally, this SERS‐active substrate can be easily cleaned and reused. The obtained results demonstrate that the DMCX‐functionalized gold colloid films prepared by self‐assembly method have great potential to be developed to an in situ PAHs detection substrate. Copyright © 2012 John Wiley & Sons, Ltd.     

Photonic bandgap via nonlinear modulation assisted by spontaneously generated coherence

A four-level double-ladder atomic system with two upper states coupled to the excited state by a standing-wave trigger field is explored to generate photonic bandgap (PBG) structure. With the assistance of spontaneously generated coherence (SGC) from the two decay pathways, we can obtain single or double fully developed PBG when the trigger field is far away from resonance or resonant. While in the absence of SGC, the atomic medium becomes strong absorptive to the probe field, and therefore the resulting PBGs are severely malformed or even cannot be opened up. Numerical results show that the PBG structure is originated from the third-order cross Kerr nonlinear modulation between the probe and trigger fields. This mechanism differs from the recent schemes based on linear modulation.     

Soot formation characteristics in a lab-scale turbulent pulverized coal flame with simultaneous planar measurements of laser induced incandescence of soot and Mie scattering of pulverized coal

Soot formation characteristics of a lab-scale pulverized coal flame were investigated by performing carefully controlled laser diagnostics. The spatial distributions of soot volume fraction and the pulverized coal particles were measured simultaneously by laser induced incandescence (LII) and Mie scattering imaging, respectively. In addition, the radial distributions of the soot volume fraction were compared with the OH radical fluorescence, gas temperature and oxygen concentration obtained in our previous studies [1], [2]. The results indicated that the laser pulse fluence used for LII measurement should be carefully controlled to measure the soot volume fraction in pulverized coal flames. To precisely measure the soot volume fraction in pulverized coal flames using LII, it is necessary to adjust the laser pulse fluence so that it is sufficiently high to heat up all the soot particles to the sublimation temperature but also sufficiently low to avoid including a too large of a change in the morphology of the soot particles and the superposition of the LII signal from the pulverized coal particles on that from the soot particles. It was also found that the radial position of the peak LII signal intensity was located between the positions of the peak Mie scattering signal intensity and peak OH radical signal intensity. The region, in which LII signal, OH radical fluorescence and Mie scattering coexisted, expanded with increasing height above the burner port. It was also found that the soot formation in pulverized coal flames was enhanced at locations where the conditions of high temperature, low oxygen concentration and the existence of pulverized coal particles were satisfied simultaneously.