The Role of Radical Bridges in Polynuclear Single-Molecule Magnets

Employing radical bridges between anisotropic metal ions has been a viable route to achieve high-performance single-molecule magnets (SMMs). While the bridges have been mainly considered for their ability to promote exchange interactions, the crystal-field effect arising from them has not been taken into account explicitly. This lack of consideration may distort the understanding and limit the development of the entire family. To shed light on this aspect, herein we report a theoretical investigation of a series of N -radical-bridged diterbium complexes. It is found that while promoting strong exchange coupling between the terbium ions, the N -radical induces a crystal field that interferes destructively with that of the outer ligands, and thus reduces the overall SMM behavior. Based on the theoretical results, we conclude that the SMM behavior in this series could be further maximized if the crystal field of the outer ligands is designed to be collinear with that of the radical bridge. This conclusion can be generalized to all exchange-coupled SMMs.     

ICP－AES法测定金属矿产品中的磷

本文研究了铁矿石、铬矿石、锰矿石中的微量磷的电感耦合等离子体发射光谱法的测定。方法简便，具有很好的精密度和准确度。标准样品的分析结果基本与标称值相吻合，回收率在９５％－１０５％之间。     

溶胶-凝胶制备技术与新型催化材料Ⅲ.溶胶粒子表面修饰方法制备催化膜

提出用溶胶粒子表面修饰方法，结合溶胶凝胶技术制备无机催化膜．该方法的基本原理是利用合适的金属配合物在胶粒表面的吸附作用，经溶胶凝胶过程，将活性组分结合到无机膜中．实验测定结果表明：（ＮｉＥＤＴＡ）２－，ＶＯ－３，ＭｏＯ２－４，（Ｐｄ（ＮＨ３）４）２＋，ＰｄＣｌ２－４，ＰｔＣｌ２－６和ＲｈＣｌ３－６可用来修饰ＡｌＯＯＨ溶胶．以Ｐｄ／γＡｌ２Ｏ３催化膜的制备为例，经三次溶胶凝胶过程，可制得无裂缺的厚度为９μｍ的Ｐｄ／γＡｌ２Ｏ３催化膜，膜材料的平均孔直径为６ｎｍ，Ｐｄ被均匀地分布在膜的顶层，其平均粒径为２３ｎｍ．     

对位酚类衍生物作为化学发光分析的增强剂研究

在化学发光分析中，常常要用到碱性条件下鲁米诺与过氧化氢的反应系统，通过催化剂辣根过氧化物酶使反应顺利进行。如果再加入适当的增强剂，则灵敏度提高且发光时间延长，可改善测定的重现性。实验证明，对位酚类衍生物，如：对叔丁基苯酚，对甲苯酚的发光增强作用明显，其发光效率可上升几十倍，发光时间也获得有效延长。     

Diode-pumped 671 nm laser frequency doubled by CPM LBO

A design of diode-pumped high-efficiency Nd:YVO₄/LBO red laser is reported. Using critical phase-matching (CPM) LBO, 671 nm red laser was obtained from 1342 nm light by intracavity frequency doubling. With an incident pump laser of 800 mW, using type-I and type-II CPM LBO, 97 and 52 mWTEM₀₀ mode red laser outputs were obtained, with optical-to-optical conversion efficiencies of up to 12.1% and 6.5%, respectively.     

Wechselnde Bindungen in einem Zweikörpersystem mit trockener Reibung

Übersicht Betrachtet wird ein zwangserregtes Zweikörpersystem mit wechselnden Bindungen infolge trockener Reibung. Stationäre Bewegungen werden als Grenzfall instationärer Einschwingvorgänge berechnet. Abhängig von den Systemparametern ergeben sich drei typische Bewegungsformen. Ihnen entsprechen dauernde Haftzustände, wechselnde Haft-Gleitzustände oder dauernde Gleitzustände an der Berührfläche beider Körper.

---

Intermittant constraints in a two-body-system with dry friction

Summary An externally excited two-body-system with intermittant constraints due to dry friction is considered. Stationary motions are calculated as limit cases of instationary transients. Depending on the parameters of the system, three typical modes are of interest. These correspond to permanent sticking, slipstick behaviour, or to permanent slipping in the contact surface of the bodies, respectively.

     

环保意识调查问卷的Logistic模型

本文应用多元统计分析中的方差分析 ,logistic模型等方法对环保意识调查问卷反馈的信息进行统计分析 ,建立被调查企业对环境保护意识的logistic模型 ,进而可对企业家的环境保护意识的好坏进行判断。     

Fiber-optic reflex sensor for in-line production measurement

The paper describes experiments concerning distance measurement with fiber-optic sensor and improvement of the measurement principle. The sensor probe was well-designed with a small structure and multi-function. The novel optical fiber probe arrangement as well as the possibilities of use for complex measurement problems are explained using the measurement of an internal screw thread as an example. The experimental results show that the measurement uncertainty of the thread minor diameter can reach ±10 μm, and the stability of the measurement system is better than 0.07%.     

Acoustic reflection from a baffled elastic/piezoelectric plate

A finite difference/boundary integral procedure to determine the acoustic reflected pressure from a fluid-loaded bi-laminated plate is described. The bi-laminate is composed of a piezoelectric layer and an elastic layer in contact with the fluid, and is held by an acoustically hard baffle. In the numerical model, the fluid pressure at fluid/solid interface is replaced by a continuum of point sources weighted by the normal acceleration of the elastic plate, and the governing equation system is solved in the solid domain. With the normal acceleration found, the reflected pressure in the fluid is determined by an integral expression involving the Green's function. It is demonstrated that an appropriate applied voltage potential across the piezoelectric layer has the effect of cancelling either the reflected or scattered pressure of the plate at any chosen field points in the fluid. Project supported by the National Natural Science Foundation of China (No. 10172039).