The mechanism of sonochemical degradation of a cationic surfactant in aqueous solution

The sonochemical degradation of the cationic surfactant, laurylpyridinium chloride (LPC), in water was studied at concentrations of 0.1-0.6 mM, all below its critical micelle concentration (15 mM). It has been found that the initial step in the degradation of LPC occurs primarily by a pyrolysis pathway. Chemical analysis of sonicated solutions by gas chromatography, electrospray mass spectrometry, and high performance liquid chromatography reveals that a broad range of decomposition products, hydrocarbon gases and water-soluble species, are produced. Propionamide and acetamide were identified as two of the degradation intermediates and probably formed as the result of the opening of the pyridinium ring following OH radical addition. Most of the LPC is eventually converted into carboxylic acids. The complete mineralization of these carboxylic acids by sonolysis is however a comparatively slow process due to the hydrophilic nature of these low molecular weight products.     

Detection of blood flow through artery in the presence of steno-occlusive disease post liver transplantation by modeling for theatrical and detrimental environmental changes

This research intends to expand a mathematical model for studying the non-Newtonian surge of blood through a hepatic artery in the presence of steno occlusive disease post-liver transplantation. Power law liquid demonstrates the non- Newtonian character of blood. The hemodynamic conduit of the fluid is altered by the occurrence of arterial stenosis. In our study, the difficulty is resolved by applying diagnostic methods with the assistance of marginal circumstances and consequences. The outcomes are explained graphically for unusual cases for such stenosis. The study design is based on a tensorial form and converts its solution using numerical and analytical techniques. Our study outcome suitably demonstrates that the mathematical model used corroborates with the clinical scenario of the patient with hepatic disease.     

UDE-based decoupled full-order sliding mode control for a class of uncertain nonlinear MIMO systems

In this paper, a generalized control scheme for the class of nonlinear multiple-input multiple-output (MIMO) uncertain system with cross-coupling and nonlinearity in their input channels under the influence of external disturbances is presented. This is accomplished using full-order model following sliding mode control based on uncertainty and disturbance estimator (UDE) technique. The fourth-order uncertain nonlinear MIMO system is separated into multiple single-input single-output double integrator subsystems by considering the effect of input coupling and nonlinearity as a disturbance. The UDE is designed to estimate the plant uncertainties as well as external disturbances without the knowledge of the bounds on the uncertainties. The proposed method decouples the system and overcomes the problem of high initial control which ultimately eliminates the reaching phase and the chattering phenomenon which is generally occurred in sliding mode control. The effectiveness of the proposed control scheme is demonstrated through numerical simulation of two-link manipulator.     

Antistatic applications of conducting polyaniline

A method is described to impart flexibility and mechanical strength to conducting polyaniline by polymerizing aniline on fabrics and on cellulose papers. The study indicates that these conducting fabrics offer 16–18 dB of shielding effectiveness for the control of electromagnetic interference (EMI) up to a frequency of 10³ MHz.     

Multi-band phase shifter design using modified slotline configuration

In this paper, an analog multiband phase shifter using slotline configuration is proposed. To implement the design, a pair of modified Split Ring Resonator (SRR) is employed. The periodic property of SRR provides multiband characteristics, whether the coupling slot gives the phase variations over the bands. The operation is well explained with an equivalent circuit model and its characteristics have been studied both in simulation and measurement. The prototype operates in 1.77–2.16, 3.5–3.97, 5.08–5.33, 6.43–6.93, and 8.01–8.59 GHz frequency bands which can be utilized for GSM, GPS, WLAN, C-band, and X-band applications, respectively.     

Instabilities in free-surface electroosmotic flows

Instability of a thin electrolyte film undergoing a direct current electroosmotic flow has been investigated. The film with a compliant electrolyte–air interface is flowing over a rigid charged substrate. Unlike previous studies, inclusion of the Maxwell stresses in the formulation shows the presence of a new finite wavenumber shear-flow mode of instability, alongside the more frequently observed long-wave interfacial mode. The shear mode is found to be the dominant mode of instability when the electrolyte–solid and electrolyte–air interfaces are of opposite charge or of same charge but have very large zeta-potential at the electrolyte–air interface. The conditions for mode-switch (interfacial to shear) and the direction of the travelling waves are discussed through stability diagrams. Interestingly, the analysis shows that when the interfaces are of nearly same zeta potential, the ‘free’ electrolyte–air interface behaves more like a ‘stationary’ wall because of the ion transport in the reverse direction of the flow.     

Interplay between bulk viscoelasticity and surface energy in autohesive tack of rubber‐tackifier blends

The effects of change in surface energy and bulk viscoelastic properties on the autohesive tack strength of brominated isobutylene‐co‐p‐methylstyrene (BIMS) rubber have been investigated by the addition of hydrocarbon resin (HCR) tackifier and maleated hydrocarbon resin (MA‐g‐HCR) tackifier. The addition of compatible HCR tackifier results in a reasonable increment in the tack strength of BIMS rubber by modifying only the bulk viscoelastic properties (compliance, entanglement molecular weight, relaxation time, self‐diffusion, and monomer friction coefficient values) of BIMS rubber to perform better during the course of bonding and debonding steps of the peel test. Incorporation of MA‐g‐HCR tackifier (containing 5–20 wt % of grafted maleic anhydride) steadily increases the tack strength of BIMS rubber further by precisely modifying both the surface energy and bulk viscoelastic properties to perform much better in the bonding and debonding steps. However, beyond 20 wt % of grafted maleic anhydride in the HCR tackifier, the tack strength starts decreasing due to the incompatibility between the blend components, and hence, the bulk viscoelastic properties required for bond formation are severely retarded by the interrelated reinforcing effect and the phase separation effect of the brittle MA‐g‐HCR tackifier in the BIMS rubber. Hence, the polar groups in a tackifier will contribute to significant enhancement of autohesive tack strength only if the bulk viscoelastic property of the rubber‐tackifier blend is favorable for bond formation and bond separation. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 972–982, 2010     

On Using Tabu Search for Design Automation of VLSI Systems

Tabu search is a meta-heuristic problem solving technique that, when applied carefully, provides near optimal solutions in a very short time. In this paper, we have described the use of tabu search for solving problems related to very large scale integrated (VLSI) circuit design automation. Specifically, we have demonstrated the use for VLSI circuit partitioning and placement. We present a tabu search based circuit bi-partitioning technique that partitions circuits with the goal of minimizing the size of the cutset between the partitions. Then, we use tabu search techniques along with force directed placement techniques to accomplish the physical placement of VLSI circuits on regular two-dimensional arrays with the goal of minimizing the placement time. We use empirical data from partitioning and placement of benchmark circuits to test our techniques. Our methods show improvement when compared to partitioning techniques from the literature and commercially available placement tools. Relative to the literature, our tabu search bi-partitioning technique improves on the best known minimum cuts for several benchmark circuits. Relative to commercially available computer aided design tools, our tabu search based placement approach shows dramatic (20×) speedup in execution time without negative impact on the quality of the solution.