High temperature NMR approach of mixtures of rare earth and alkali fluorides: An insight into the local structure

In situ high temperature nuclear magnetic resonance in molten fluoride mixtures gives some structural picture of the complexes existing in the melt, i.e. of their nature and relative proportion. Thanks to the development of a laser heating system associated with a close crucible in boron nitride, we can describe experimentally the evolution of these complexes from the anions and the cations point of view. By ¹⁹F NMR, we have shown the existence of three kinds of fluorine atoms depending on the composition: free fluorine like in pure LiF (non-bonded), bridging fluorine in melts rich in LnF₃ in addition with terminal fluorine singly bonded to one rare earth. Data obtained by NMR spectroscopy are also combined with EXAFS measurements, again thanks to a specific development of the sample holder adapted with molten fluorides and high temperature. This study is a part of our systematic investigation of the different Alk-LnF₃ systems by NMR and EXAFS spectroscopy.     

Bridging M?Cl Bonds with Ambiphilic Phosphine–Borane Ligands

Bridging or pendant? Palladium and rhodium complexes deriving from an ambiphilic phosphine–borane ligand are shown to adopt a bridging P→M? Cl→B coordination mode in the solid state. DFT calculations provide more insight into the Cl→B interaction and suggest the possible interconversion of the bridging and B‐pendant forms in solution.

     

Validation of a new method using the reactivity of electrogenerated superoxide radical in the antioxidant capacity determination of flavonoids

This article lays out a new method to measure the antioxidant capacity of some flavonoids. The methodology developed is based on the kinetics of the reaction of the antioxidant substrate with the superoxide radical (O(2)(*-)). A cyclic voltammetric technique was used to generate O(2)(*-) by reduction of molecular oxygen in aprotic media. In the same experiment the consumption of the radical was directly measured by the anodic current decay of the superoxide radical oxidation in the presence of increasing concentrations of antioxidant substrate. The method was statistically validated on flavonoid monomers and on the standard antioxidants: trolox, ascorbic acid and phloroglucinol. The linear correlations between the anodic current of O(2)(*-) and the substrate concentration allowed the determination of antioxidant index values expressed by the substrate concentration needed to consume 30% (AI(30)) and 50% (AI(50)) of O(2)(*-) in given conditions of oxygen concentration and scanning rate. The fidelity of the method was examined intraday and interlaboratories.     

Heparin coating of poly(ethylene terephthalate) decreases hydrophobicity, monocyte/leukocyte interaction and tissue interaction

Woven poly(ethylene terephthalate) (PET) is widely used in implantable medical devices. Upon implantation, fibrinogen interacts with the PET and changes conformation, such that the fibrinogen P2 epitope may become exposed. This allows inflammatory cells to interact with the material. In this study we have coated PET with heparin and show that this decreases PET hydrophobicity and the presence of the fibrinogen P2 epitope on the material surface. In addition, we show that heparin-induced reduction of PET hydrophobicity correlates with decreased exposure of the fibrinogen P2 epitope and reduced adhesion of monocytes. Reduction of PET hydrophobicity was furthermore associated with reduced PMN elastase production and decreased interaction between PET and embryonic chicken tissue. We conclude that the heparin coating-induced decrease in PET hydrophobicity is associated with decreased interaction between PET and inflammatory cells. Independent of this interaction, the hydrophobic nature of the heparin coating is related to tissue interaction as demonstrated by a reduction in adhesion, growth and spreading of tissue on PET. The combination of these properties makes heparin coating a candidate for improving biocompatibility of PET.     

Heat-treated Saccharomyces cerevisiae for antimony speciation and antimony(III) preconcentration in water samples

An analytical method was developed for antimony speciation and antimony(III) preconcentration in water samples. The method is based on the selective retention of Sb(III) by modified Saccharomyces cerevisiae in the presence of Sb(V). Heat, caustic and solvent pretreatments of the biomass were investigated to improve the kinetics and thermodynamics of Sb(III) uptake process at room temperature. Heating for 30 min at 80 degrees C was defined as the optimal treatment. Antimony accumulation by the cells was independent of pH (5-10) and ionic strength (0.01-0.1 mol L(-1)). 140 mg of yeast and 2h of contact were necessary to ensure quantitative sequestration of Sb(III) up to 750 microg L(-1). In these conditions, Sb(V) was not retained. Sb(V) was quantified in sorption supernatant by inductively coupled plasma mass spectrometry (ICP-MS) or inductively coupled plasma optical emission spectrometry (ICP-OES). Sb(III) was determined after elution with 40 mmol L(-1) thioglycolic acid at pH 10. A preconcentration factor close to nine was achieved for Sb(III) when 100mL of sample was processed. After preconcentration, the detection limits for Sb(III) and Sb(V) were 2 and 5 ng L(-1), respectively, using ICP-MS, 7 and 0.9 microg L(-1) using ICP-OES. The proposed method was successfully applied to the determination of Sb(III) and Sb(V) in spiked river and mineral water samples. The relative standard deviations (n=3) were in the 2-5% range at the tenth microg L(-1) level and less than 10% at the lowest Sb(III) and Sb(V) tested concentration (0.1 microg L(-1)). Corrected recoveries were in all cases close to 100%.     

Efficient, mild, parallel and purification-free synthesis of aryl ethers via the Mitsunobu reaction

A wide range of commercial diazodicarboxylates and phosphines were screened in an attempt to find purification-free conditions for application in parallel synthesis. The combination of immobilized triphenylphosphine and TMAD proved to be suitable for the synthesis of aryl ethers via the Mitsunobu reaction. Nine ethers were synthesized in good yield and excellent purity, the purification being limited to a filtration step.     

New dehydration in the pyrrolo[1,2–6-b]isoquinoline series. Preparation and structural identification of 3,5-dihydrobenz[f]indolizin-3-one

3,5-Dihydrobenz[f]indolizin-3-one was prepared by a novel dehydration reaction involving the heating of 1,2,3,5,10,10a-hexahydro[f]indolizine-3,10-dione with polyphosphoric acid. The structure of this new compound was established by X-ray crystallography, by nmr spectroscopy and by reduction to the known products 1,2,3,5-tetrahydrobenz[f]indolizin-3-one and 1,2,3,5,10,10a-hexahydrobenz[f]indolizin-3-one.     

Stereochemical Aspects in the Asymmetric Michael Addition of Chiral Imines to Substituted Electrophilic Alkenes

The Michael-type addition of chiral imines, derived from racemic alpha-substituted cyclanones and optically active 1-phenylethylamine, to electrophilic alkenes, in neutral conditions, constitutes one of the most efficient methods for the stereocontrolled construction of quaternary carbon centers. In order to create an additional stereogenic center at the alpha- or beta-position to the quaternary one, the behavior of a variety of alpha- and beta-substituted alkenyl acceptors was examined. In general, these additions are highly regioselective, the alkylation taking place predominantly, if not exclusively, at the more substituted alpha-side of the imine function; however, in some cases (electrophilic alkenes 28 and 49), significant amounts (10-15%) of regioisomeric adducts were obtained. With the exception of methyl propiolate 52, a remarkable control of the absolute configuration of the adducts were always observed with these Michael acceptors. According to the general rule we have previously proposed, the alkylation process takes place preferentially on the less hindered pi-face of the more substituted secondary enamine, in tautomeric equilibrium with the starting imine. An excellent diastereocontrol was always obtained by using the present alpha- and beta-substituted alkenes. These stereochemical outcomes can be interpreted by invoking that the reaction proceeds through a compact approach of the reactants, the hydrogen atom at the nitrogen center of the enamine being transferred to the alpha-vinylic carbon atom of the acceptor, concertedly with the creation of the C-C bond. In this respect the "endo-approach" 58, in which the electron-withdrawing group of the acceptor faced to the nitrogen atom of the enamine (case of acceptors 10, methyl methacrylate, 24, 28, 43, 47, and 49) largely prevails over the "exo-approach" 59 (case of acceptor 38). This predominant "endo-preference" can be reasonably interpreted in terms of a cooperative effect between steric and stereoelectronic factors.     

Evaluation of an accurate calibration and spectral standardization procedure for Raman spectroscopy

Due to modern developments Raman spectroscopy has evolved into a fast vibrational technique. Detailed fingerprints in combination with non-destructivity and minimal sample preparation has allowed the construction of reference libraries in a variety of research fields. Long-term stability and comparability are important characteristics when developing reference libraries. In addition, small shifts in highly similar spectra of different samples may limit the full potential of Raman spectroscopy. Since libraries often contain a large number of different and/or highly similar spectra, it is important that each data point in all the spectra corresponds to the exact Raman wavenumber. This is often not the case, due to shifts in optical pathway and/or shifts in laser wavelength. This paper describes a complete calibration protocol (wavelength and intensity) and evaluates the procedure for both short and long term stability, by means of 60 randomly selected measurement sessions spread over a period of nine months. A two-step standardization procedure is proposed to deal with spectral shifts.     

Trichlorosilane isocyanate as coupling agent for mild conditions functionalization of silica-coated surfaces

Despite the importance of the isocyanate group in chemistry, very few examples of isocyanate-modified silicas have been reported, and all of the strategies described so far led to partial or total hydrolysis or condensation of the isocyanate group. By synthesizing trichlorosilane isocyanate as the coupling reagent, we show that oxidized silicon wafers are successfully modified with the isocyanate group. Our method is achieved in mild conditions, at low temperature, without side-reactions and allows the formation of a self-assembled monolayer (SAM) of isocyanates. The isocyanate group then offers a flexible way to further functionalize silica substrates with different nucleophiles, due to its high and specific reactivity.