Evaluations of solid electrodes for use in voltammetric monitoring of heavy metals in samples from metallurgical nickel industry

Evaluation of different solid electrode systems for detection of zinc, lead, cobalt, and nickel in process water from metallurgical nickel industry with use of differential pulse stripping voltammetry has been performed. Zinc was detected by differential pulse anodic stripping voltammetry (DPASV) on a dental amalgam electrode as intermetallic Ni–Zn compound after dilution in ammonium buffer solution. The intermetallic compound was observed at –375 mV, and a linear response was found in the range 0.2–1.2 mg L^–1 (r²=0.98) for 60 s deposition time. Simultaneous detection of nickel and cobalt in the low g L^–1 range was successfully performed by use of adsorptive cathodic stripping voltammetry (AdCSV) of dimethylglyoxime complexes on a silver–bismuth alloy electrode, and a good correlation was found with corresponding AAS results (r²=0.999 for nickel and 0.965 for cobalt). Analyses of lead in the g L^–1 range in nickel-plating solution were performed with good sensitivity and stability by DPASV, using a working electrode of silver together with a glassy carbon counter electrode in samples diluted 1:3 with distilled water and acidified with H₂SO₄ to pH 2. A new commercial automatic at-line system was tested, and the results were found to be in agreement with an older mercury drop system. The stability of the solid electrode systems was found to be from one to several days without any maintenance needed.     

Henry's law and diffusion constants of vinyl chloride in poly(vinyl chloride) at high temperature

The Henry's law and diffusion constants of vinyl chloride in poly(vinyl chloride) were determined at temperatures of 24, 90, 120, 150, and 170°C for weight fractions of vinyl chloride between 0.2 × 10^?3 and 0.8 × 10^?3. Above 90°C, Henry's law applies; values of the constant increase with temperature from 1.8 × 10² to 5.5 × 10² atm per unit weight fraction of dissolved vinyl chloride. The heat of desorption is about 15 kJ/mole. At 24°C, the nominal Henry's law constant was smaller than would have been obtained by extrapolating the values found at higher temperature. The diffusion constants increase with temperature from about 2 × 10^?13 to 3 × 10^?7 cm²/sec. The activation energy for diffusion is about 110 kJ/mole between 90 and 170°C. Although all values were determined in the absence of air, it is likely that they apply to polymer in air. They may, therefore, be used to calculate the vinyl chloride content in the gas above poly(vinyl chloride) under specific processing conditions.     

N,N,N′,N′-Tetrabutyl-3,6-dioxaoctan-dithioamid,Ionophor mit Selektivität für Cd2+

N,N,N′,N′-Tetrabutyl-3,6-dioxaoctane-dithioamide, an Ionophore with Selectivity for Cd²⁺ The dioxa-dithioamide 3 behaves as a highly selective ionophore for Cd²⁺ in solvent polymeric membranes. It induces cation-permselectivity in these membranes with a transference number of 1 for Cd(NO₃)₂- and of 2 for CdCl₂-solutions. In the presence of a proton carrier, 3 may be used to selectively pump Cd²⁺ through membranes by coupling with a pH gradient.     

über Katalysatoren- und Fermentmodelle (1)

Ohne Zusammenfassung Die Arbeit wurde aus Mitteln des Marshall-Planes (ERP-Mittel) und mit Spenden aus dem „Fonds Chemie“ ausgeführt. Wir sprechen den zust?ndigen Stellen für die Gew?hrung der Beihilfe unseren verbindlichsten Dank aus. Der Deutschen Forschungsgemeinschaft danken wir für die überlassung einer Ultrazentrifuge, den Behring-Werken für die uns zur Verfügung gestellten Serumalbumin- und -globulin-Pr?parate.     

Volume and heat capacity of model non-aqueous self-assembly systems

Blends of immiscible polymers are often stabilized by block copolymers which can form non-aqueous micelles and microemulsions in the liquid polymers. The phase diagrans, apparent volumes and apparent heat capacities of model non-aqueous binary and ternary systems were studied in order to investigate the conditions under which such self-assembly systems could form. 1,2-Hexanediol, which can cosolubilize hexane and ethyleneglycol, forms inverse micelles in hexane and weak microaggregates in ethyleneglycol. Genapol X-060, a commercial alcoholic surfactant containing on the average an aliphatic chain of 13 carbons and 6 oxyethylenes (C₁₃E₆), forms microaggregates in poly(ethyleneglycol) 400. These self-assembly systems are strengthen in the presence of a third component which has an affinity for the inner phase.Presented at the Symposium, 76^th CSC Congress, Sherbrooke, Quebec, May 30–June 3, 1993, honoring Professor Donald Patterson on the occasion of his 65^th birthday.     

Statistical treatment of proficiency testing data

 There are three stages to evaluating a laboratory's results in an interlaboratory proficiency test: establishing the correct result for the test item, determining an evaluation statistic for the particular result, and establishing an acceptable range. There are a wide variety of procedures for accomplishing these three stages and a correspondingly wide variety of statistical techniques in use. Currently in North America the largest number of laboratory proficiency test programs are in the clinical laboratory field, followed by programs for environmental laboratories that test drinking water and waste water. Proficiency testing in both of these fields is under the jurisdiction of the federal government and other regulatory and accreditation agencies. Many of the statistical procedures are specified in the regulations, to assure comparability of different programs and a fair evaluation of performance. In this article statistical procedures recommended in International Organization for Standardization Guide 43, Part 1, are discussed and compared with current practices in North America. Received: 22 April 1998 · Accepted: 12 May 1998     

Engineered protein cages for nanomaterial synthesis

Self-assembled particles of genetically engineered human L subunit ferritin expressing a silver-binding peptide were used as nanocontainers for the synthesis of silver nanoparticles. The inner cavity of the self-assembled protein cage displays a dodecapeptide that is capable of reducing silver ions to metallic silver. This chimeric protein cage when incubated in the presence of silver nitrate exhibits the growth of a silver nanocrystal within its cavity. Our studies indicate that it is possible to design chimeric cages, using specific peptide templates, for the growth of other inorganic nanoparticles.     

Selective, controllable, and reversible aggregation of polystyrene latex microspheres via DNA hybridization

The directed three-dimensional self-assembly of microstructures and nanostructures through the selective hybridization of DNA is the focus of great interest toward the fabrication of new materials. Single-stranded DNA is covalently attached to polystyrene latex microspheres. Single-stranded DNA can function as a sequence-selective Velcro by only bonding to another strand of DNA that has a complementary sequence. The attachment of the DNA increases the charge stabilization of the microspheres and allows controllable aggregation of microspheres by hybridization of complementary DNA sequences. In a mixture of microspheres derivatized with different sequences of DNA, microspheres with complementary DNA form aggregates, while microspheres with noncomplementary sequences remain suspended. The process is reversible by heating, with a characteristic "aggregate dissociation temperature" that is predictably dependent on salt concentration, and the evolution of aggregate dissociation with temperature is observed with optical microscopy.     

One-pot tethering of organic molecules through non-symmetric malonate derivatives

A new method for one-pot chemoselective heterobifunctional cross-linking of organic molecules is described. The method is based on tert-butyldiphenylsilyl malonate and involves two sequential carbodiimide couplings with two different molecules possessing a hydroxy or an amino functionality with one intermediate one-pot fluoride deprotection.     

Detection of Trace concentrations of gases with coated piezoelectric quartz crystals

Coated piezoelectric crystal sensors for determination of trace constituents in gases are very sensitive. Detection limits down to the sub-ppb range have been reported, using injection techniques. From previous and presented data, this high sensitivity is found to be in disagreement with Sauerbrey's eqn., which allows a maximum sensitivity of about 1 ppm. By considering the adsorption of the gases on the coated surface and the calibration procedures used, the validity of Sauerbrey's eqn. is discussed.