Specific determination of 20 primary aromatic amines in aqueous food simulants by liquid chromatography-electrospray ionization-tandem mass spectrometry

A multi-analyte method without any pre-treatment steps using reversed-phase liquid chromatography-electrospray ionization-tandem mass spectrometry (LC-ESI-MS/MS) was developed and applied for the determination of 20 primary aromatic amines (PAA) associated with polyurethane (PUR) products or azo-colours. The method was validated in-house for water and 3% acetic acid food simulants using spiked migrates from plastic laminates. Detection limits ranged from 0.27 to 3 microg amine/L food simulants, and RSD values of within-laboratory reproducibility at the 2 microg PAA/L level ranged from 3.9 to 19%. PAA migration from plastic laminates and black nylon cooking utensils were determined with the method, and high levels of 4,4'-methylenedianiline and aniline were found in migrates from about half of the tested cooking utensils. The method fulfils present legislative demands in the EU for screening and verification of PAA migration from food contact materials.     

Comparison between high-performance liquid chromatography and gas chromatography methods for fatty acid identification and quantification in potato crisps

A reversed-phase high performance liquid chromatographic (RP-HLPC) method was compared with a gas chromatography-flame ionization detection (GC-FID) method for determining fatty acids in potato crisps. Different extraction procedures were used. Fatty acids were quantified by linear regression. Both methods presented good precision (R.S.D. < or = 5.88%) and recovery (> or = 82.31%). The precision using HPLC method was slightly better than for GC-FID method. There was good agreement between the fatty acid composition of potato crisps analysed by both methods. For most purposes the HPLC method would be better. However, when more fatty acids need to be analysed, GC is a more suitable method.     

Carbon nanotube array-based biosensor

Aligned multi-wall carbon nanotubes (MWNT) grown on platinum substrate are used for the development of an amperometric biosensor. The opening and functionalization by oxidation of the nanotube array allows for the efficient immobilization of the model enzyme, glucose oxidase. The carboxylated open-ends of nanotubes are used for the immobilization of the enzymes, while the platinum substrate provides the direct transduction platform for signal monitoring. It is also shown that carbon nanotubes can play a dual role, both as immobilization matrices and as mediators, allowing for the development of a third generation of biosensor systems, with good overall analytical characteristics.     

Atomization of Al in a tungsten coil electrothermal atomic absorption spectrophotometer

Electrothermal atomic absorption spectrophotometry of Al in a tungsten coil atomizer was evaluated and applied for its determination in hemodialysis fluid. The system was mounted on a Varian Spectra AA-40 spectrophotometer with continuum background correction and all measurements, in peak height absorbance, were done at 309.3 nm. The purge gas was a mixture of 90% Ar plus 10% H(2). Observation height, gas flow, drying, pyrolysis and atomization steps were optimized. The heating program was carried out by employing a heating cycle in four steps: dry, pyrolysis, atomization and clean. The determination of Al in hemodialysis solutions was performed by using a matrix-matching procedure. Al in hemodialysis solutions was determined by TCA and by electrothermal atomization with a graphite tube atomizer. There is no differences between results obtained by both methods at a confidence level of 95%. The characteristic mass of Al by using the TCA was 39 pg and the detection limit was 2.0 mug l(-1).     

Binary mixtures based on polycaprolactone and cellulose derivatives

Pyrolytic process has a promising potential for the environmentally friendly upgrading of lignocellulosic and plastic waste. Thermogravimetry and pyrolysis-gas chromatography-mass spectrometry (Py-GC/MS) were used to get information about the reactive decomposition of PCL in binary mixtures with microcrystalline cellulose (MC) or sisal fibres (SF). Preliminary thermogravimetric investigation showed that biomass is thermally degraded at lower temperatures than PCL and this process has a predominant influence on the thermal behaviour of the mixtures. Discrepancies between the experimental and predicted TG/DTG profiles were considered as a measurement of the extent of interactions occurring on co-pyrolysis. It was found that reactivity of PCL was slightly increased in PCL-SF binary mixtures. Evolution of acidic products from cellulose and hemicelluloses decomposition may promote PCL degradation in binary mixtures with SF. It seems that the co-pyrolysis process could have potential for the environmentally friendly transformation of biocomposites.     

Determination of major and trace elements in crude oils by neutron activation and reflection methods

The concentrations of O, Na, Cl, V, Mn and Ni in crude oils of different origins were determined, using sampling (SNAA) and on-stream (ONAA) activation analyses. Samples were irradiated with thermal and fast neutrons produced by a 0.3 mg²⁵²Cf source and a 14 MeV generator. The H-content and the C/H atomic ratio have been determined by thermal neutron reflection method using an 18 GBq Pu−Be source. This work was supported in part by the Hungarian Academy of Sciences.     

Thermal Behaviour of some dioxane adducts ofM(C6F5)2 (M=Pd,Pt)

The thermal treatment of the pentafluorophenyl derivativesM(C₆F₅)₂Dx_n [M=Pd (n=2, 3) or Pt (n=2); Dx=dioxane] leads to the formation of the new dioxane adducts M(C₆F₅)₂Dx (M=Pd, Pt) and Pt(C₆F₅)₂Dx_1.5. Calculations of the order of reaction and the activation energy of some of the decomposition reactions are described. The values were determined by the Coats-Redfern and Freeman-Carroll methods. Structural data on the isolated intermediates were obtained by infrared spectroscopy and magnetic susceptibility measurements.

---

Zusammenfassung Die thermische Behandlung der PentafluorphenylderivateM(C₆F₅)₂Dx_n [M=Pd (n=2, 3) oder Pt (n=2); Dx=Dioxan] führt zu der Bildung der neuen DioxanaddukteM(C₆F₅)₂Dx (M=Pd, Pt) und Pt(C₆F₅)₂Dx_1.5. Die Berechnungen der Reaktionsordnung und der Aktivierungsenergie einiger Zersetzungsreaktionen werden beschrieben. Die Werte wurden durch die Methoden von Coats-Redfern und Freeman-Carroll bestimmt. Die Strukturangaben der isolierten Zwischenprodukte wurden durch Infrarotspektroskopie und Messung der magnetischen Suszeptibilität erhalten.

---

(₆F₅)₂, M=Pd n=2, 3 Pt _n=2, - , -M(C₆F₅)₂ (=Pd, Pt) (₆F₅)_21,5. , — —. .

     

Pyrylium-containing polymers as sensory materials for the colorimetric sensing of cyanide in water

A sensory polymeric material for the colorimetric sensing of cyanide in water has been developed based on the reactivity of this anion with the pyrylium cation.     

Entropy evaluation using the kinetic method: is it feasible?

The kinetic method is one of the most widely used experimental techniques for the measurement of thermochemical parameters by mass spectrometry. Recently it has been realized that it can also be used to determine reaction entropies, but the validity of this approach has not been established. This Perspective evaluates kinetic method plots in cases where there is a significant entropy difference between the competing fragmentation channels (i.e. between sample and reference compounds in the dissociating cluster ion). The concept underlying this study is to calculate mass spectra theoretically, based on known thermochemical parameters and as a function of experimental conditions. This can be done accurately using the RRKM-based MassKinetics software. The resulting mass spectra are then interpreted by the kinetic method, yielding DeltaH and DeltaS values. These values are, in turn, compared with the true values used to generate the calculated mass spectra. The results show that the reaction entropy difference between sample and reference has a very large influence on kinetic method plots. This should always be considered when studying energy-dependent mass spectra (using metastable ions or low- or high-energy collision-induced dissociation (CID)), even if only DeltaH is to be determined. Kinetic method plots are not strictly linear and this becomes a serious issue in the case of small molecules showing a large entropy effect. In such cases, results obtained at a low degree of excitation are more accurate. Energy and entropy effects can be evaluated in a relatively straightforward manner: first, the apparent Gibbs energy (DeltaG(app)) and effective temperature (T(eff)) are determined from kinetic method plots (intercept and slope, respectively), obtained from experiments using various degrees of excitation. Second, the resulting DeltaG(app) is plotted against T(eff), the slope yielding DeltaS while the intercept (extrapolation to zero temperature) yields DeltaH. This data evaluation yields more accurate results than alternative methods used in the literature. The resulting DeltaH values are fairly accurate, with errors, in most cases, <4 kJ mol(-1). On the other hand, DeltaS is systematically underestimated by 20-40%. Empirically scaling DeltaS values determined by the kinetic method by 1.35 results in a DeltaS value within 20% (or 10 J mol(-1) K(-1)) of the theoretical value.     

Direct determination of gallium on polyurethane foam by X-ray fluorescence

Gallium chloride is easily extracted from 6M HCl by comminuted polyether-type polyurethane foam. After the extraction step, the gallium absorbed by the PU foam can be quantitatively determined by X-ray fluorescence. A procedure for the direct determination of gallium absorbed by PU foam by XRFS is thus described. Gallium is determined at levels as low as 60 ng/ml (C(L)), with a calibration sensitivity of 424 cps ml/mug, within a linear range 0.1-2.30 mug/ml. The procedure investigated was successfully applied to determination of gallium in aluminum alloys, bauxite and industrial residue samples.