Phthalonitrile‐containing aromatic polyimide thin films with nano‐actuation properties

Polymer films of some polyimides containing pendant phthalonitrile groups were prepared by casting the corresponding poly(amic acid) solutions onto glass plates, followed by thermal imidization under controlled temperature conditions. The poly(amic acid)s were synthesized by polycondensation reaction of 4,4′‐diamino‐4″‐(3,4‐dicyanophenoxy)triphenylmethane, 1, or of different amounts of 1 and 4,4′‐bis(4‐aminophenoxybiphenyl), with two aromatic dianhydrides, 4,4′‐oxydiphthalic anhydride or benzophenone‐3,3′,4,4′‐tetracarboxylic dianhydride. Most of the films were flexible and tough and exhibited high thermal stability, having the initial decomposition temperature above 400 °C. Dynamic mechanical analysis and dielectric spectroscopy revealed the influence of phthalonitrile group content on the relaxation processes of polyimides. The values of the dielectric constant at 10 kHz and 20 °C were in the range of 3.25–3.61. The films exhibited nano‐actuation in the range of 240–480 nm, depending on the phthalonitrile group content, when an electric voltage was applied on their surface. Copyright © 2012 John Wiley & Sons, Ltd.     

The advantageous way of getting the lowest uncertainty values of elemental concentration by INAA

Analysts in a NAA accredited laboratory bear full responsibility for the report on the material they investigated. The document has to contain the most accurate values that can be, as confidence to further use of the material on the market. To this end, analysts are expected to use the standardization method providing the lowest element concentration uncertainty and carefully quantify every factor that may contribute to the validity of the results. The question is which method is the most advantageous one from this perspective and in what conditions. This paper presents a comparison between results of the elemental analysis of a CRM sample by INAA, as obtained through two standardization methods and three calculations variants applied to the same experimental data. The results were discussed in terms of uncertainty and of the E _n statistical criterion recommended for inter-comparison exercises. The influence of the nuclear reaction and decay data was studied in several cases.     

Synthesis and characterization of new polyesters with enhanced phosphorus content

New polyesters were prepared from several aromatic phosphonic dichlorides and a diolic monomer bearing a cyclic bulky group containing phosphorus. From kinetic investigation, the rates of polycondensation in melt were calculated and compared with those of the reaction between aromatic diols and phosphonic dichloride. Polyesters were analytically, spectral and thermally characterized and effect of structure on optical properties was investigated.     

Chemisorption of CO and mechanism of CO oxidation on supported platinum nanoclusters

Kinetic, isotopic, and infrared studies on well-defined dispersed Pt clusters are combined here with first-principle theoretical methods on model cluster surfaces to probe the mechanism and structural requirements for CO oxidation catalysis at conditions typical of its industrial practice. CO oxidation turnover rates and the dynamics and thermodynamics of adsorption-desorption processes on cluster surfaces saturated with chemisorbed CO were measured on 1-20 nm Pt clusters under conditions of strict kinetic control. Turnover rates are proportional to O(2) pressure and inversely proportional to CO pressure, consistent with kinetically relevant irreversible O(2) activation steps on vacant sites present within saturated CO monolayers. These conclusions are consistent with the lack of isotopic scrambling in C(16)O-(18)O(2)-(16)O(2) reactions, and with infrared bands for chemisorbed CO that did not change within a CO pressure range that strongly influenced CO oxidation turnover rates. Density functional theory estimates of rate and equilibrium constants show that the kinetically relevant O(2) activation steps involve direct O(2)* (or O(2)) reactions with CO* to form reactive O*-O-C*=O intermediates that decompose to form CO(2) and chemisorbed O*, instead of unassisted activation steps involving molecular adsorption and subsequent dissociation of O(2). These CO-assisted O(2) dissociation pathways avoid the higher barriers imposed by the spin-forbidden transitions required for unassisted O(2) dissociation on surfaces saturated with chemisorbed CO. Measured rate parameters for CO oxidation were independent of Pt cluster size; these parameters depend on the ratio of rate constants for O(2) reactions with CO* and CO adsorption equilibrium constants, which reflect the respective activation barriers and reaction enthalpies for these two steps. Infrared spectra during isotopic displacement and thermal desorption with (12)CO-(13)CO mixtures showed that the binding, dynamics, and thermodynamics of CO chemisorbed at saturation coverages do not depend on Pt cluster size in a range that strongly affects the coordination of Pt atoms exposed at cluster surfaces. These data and their theoretical and mechanistic interpretations indicate that the remarkable structure insensitivity observed for CO oxidation reactions reflects average CO binding properties that are essentially independent of cluster size. Theoretical estimates of rate and equilibrium constants for surface reactions and CO adsorption show that both parameters increase as the coordination of exposed Pt atoms decreases in Pt(201) cluster surfaces; such compensation dampens but does not eliminate coordination and cluster size effects on measured rate constants. The structural features and intrinsic non-uniformity of cluster surfaces weaken when CO forms saturated monolayers on such surfaces, apparently because surfaces and adsorbates restructure to balance CO surface binding and CO-CO interaction energies.     

Fluorescence properties of photonic crystals doped with perylenediimide

This study aims to present the fabrication of colloidal photonic crystals (PC) with increased fluorescence properties. The use of a highly fluorescent perylenediimide derivate (PDI) during the soap-free emulsion polymerization of styrene-acrylic acid resulted in monodisperse core-shell particles which allowed the fabrication of PC films. The properties of the hybrid material were studied in comparison with hybrid materials obtained by impregnation of films with chromophore solutions. In both cases an increase of the fluorescence response was observed in addition to a blue shift for the PDI core particles, proving the incorporation of the dye inside the copolymer particles.     

DFT study of electronic structure and optical properties of some Ru- and Rh-based complexes for dye-sensitized solar cells

The paper reports Time Dependent Density Functional Theory (TD DFT) calculations providing the structure, electronic properties and spectra of [Ru(II)(bpy)_{3? n} (dcbpy) _n ]²⁺ and [Rh(III)(bpy)_{3? n} (dcbpy) _n ]³⁺ complexes, where bpy?=?2,2′-bipyridyl, dcbpy?=?4,4′-dicarboxy-2,2′-bipyridyl, and n?=?0,?1,?2,?3, studied as possible pigments for dye-sensitized solar cells. The role of the metallic ion and of the COOH groups on the optical properties of these complexes are compared and contrasted and their relevance as dyes for hybrid organic–inorganic photovoltaic cells is discussed. It was found that the optical spectra are strongly influenced by the metallic ion, with visible absorption bands for the Ru(II) complexes and only ultraviolet bands for the Rh(III) complexes. Upon excitation, the extra positive charge of the Rh³⁺ centre tends to draw electrons towards the metal ion, facilitating some charge transfer from the ligand to the metal, whereas in the case of the Ru²⁺ ion the electron transfer is clearly from the metal to the ligand. The carboxyl groups play an important role in strengthening the absorption bands in solution in the visible region. Of the complexes studied, the most suited as pigments for dye-sensitized solar cells are the [Ru(II)(bpy)_{3? n} (dcbpy) _n ]²⁺ complexes with n?=?1 and 2. This is based on the following arguments: (i) their intense absorption band in the visible region, (ii) the presence of the anchoring groups allowing the bonding to the TiO₂ substrate and the charge transfer, and (iii) the good energy level alignment with the conduction band edge of the semiconducting substrate and the redox level of the electrolyte.     

Hybrid material based on ST–AA photonic crystal core and ZnO particle shell

The aim of this study was to obtain a hybrid material based on a polymer photonic crystal core and inorganic ZnO shell with potential applications in optoelectronic devices or photocatalysts. For this reason, ZnO particles were obtained both in the absence and presence of ST–AA particles using a chemical reduction method for metal salts. The inhibited growth mechanism of inorganic particles generated in the presence of polymer latex was noticed. The products were characterized by SEM, EDX, TEM, DLS, and UV–vis.     

Landau level spectrum for bilayer graphene in a tilted magnetic field

We consider a graphene bilayer in a constant magnetic field of arbitrary orientation, i.e., tilted with respect to the graphene plane. In the low energy approximation to the tight-binding model with Peierls substitution, we find the Landau level spectrum analytically in terms of spheroidal functions and the respective eigenvalues. We compare our result to the perpendicular and purely in-plane field cases. In the limit of perpendicular field we reproduce the known equidistant spectrum for Landau levels. In the opposite limit of large in-plane field this spectrum becomes two-fold degenerate, which is a consequence of Dirac point splitting induced by the in-plane field.