Preparation of well-aligned carbon nanotubes by pyrolysis of phenolic resin in anodic alumina pores

Well-aligned carbon nanotubes (CNTs) of high quality were synthesized by pyrolysis of phenolic resin at 800 °C in anodic alumina oxide (AAO) pores under argon protection. The innocuous source materials and safe operational conditions permit this method to synthesize well-aligned CNTs in large-scale and low cost. The formation mechanism of the synthesized CNTs is also proposed in this work by a series of visual sketches and is proved with obvious evidence. Firstly, phenolic resin nanotubes form in the template pores through the evaporation of solvent. Heat treatment then transfers these tubes into CNTs.     

Melt rheology of polylactide/montmorillonite nanocomposites

In this article, the linear and nonlinear shear rheological behaviors of polylactide (PLA)/clay (organophilic‐montmorillonite) nanocomposites (PLACNs) were investigated by an Advanced Rheology Expanded System rheometer. The nanocomposites were prepared by master batch method using a twin‐screw extruder with poly(ε‐caprolactone) (PCL) as a compatibilizer. The presence of org‐MMT leads to obvious pseudo‐solid‐like behaviors of nanocomposite melts. The behaviors caused by the formation of a “percolating network” derived from the reciprocity among the strong related sheet particles. Therefore, the storage moduli, loss moduli, and dynamic viscosities of PLACNs show a monotonic increase with MMT content. Nonterminal behaviors exists in PLACNs nanocomposites. Besides the PLACNs melts show a greater shear thinning tendency than pure PLA melt because of the preferential orientation of the MMT layers. Therefore, PLACNs have higher moduli but better processibility compared with pure PLA. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 3189–3196, 2007     

Homothetic self-similar solutions of three-dimensional Brans-Dicke gravity

All homothetic self-similar solutions of the Brans-Dicke scalar field in three-dimensional spacetime with circular symmetry are found in closed form.     

The influence of hard‐segments on two‐phase structure and shape memory properties of PCL‐based segmented polyurethanes

Poly(ε‐caprolactone)‐based segmented polyurethanes (PCLUs) were prepared from poly(ε‐caprolactone) diol, diisocyanates (DI), and 1,4‐butanediol. The DIs used were 4,4′‐diphenylmethane diisocyanate (MDI), 2,4‐toluenediisocyanate (TDI), isophorone diisocyanate (IPDI), and hexamethylene diisocyanate (HDI). Differential scanning calorimetry, small‐angle X‐ray scattering, and dynamic mechanical analysis were employed to characterize the two‐phase structures of all PCLUs. It was found that HDI‐ and MDI‐based PCLUs had higher degree of microphase separation than did IPDI‐ and TDI‐based PCLUs, which was primarily due to the crystallization of HDI‐ and MDI‐based hard‐segments. As a result, the HDI‐based PCLU exhibited the highest recovery force up to 6 MPa and slowest stress relaxation with increasing temperature. Besides, it was found that the partial damage in hard‐segment domains during the sample deformation was responsible for the incomplete shape‐recovery of PCLUs after the first deformation, but the damage did not develop during the subsequent deformation. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 557–570, 2007     

Competitive influence of atactic polystyrene and supercritical carbon dioxide on the conformation of syndiotactic polystyrene

The crystallization behavior of miscible syndiotactic polystyrene (sPS) and atactic polystyrene (aPS) blends with different sPS/aPS weight ratios was investigated in supercritical CO₂ by using Fourier‐transform infrared spectroscopy, differential scanning calorimetry, and wide‐angle X‐ray diffraction. Supercritical CO₂ and aPS exhibited different effects on the conformational change of sPS and competed with each other. Increasing the content of amorphous aPS in the blends made its effect on the conformational change of sPS gradually surpass that of supercritical CO₂. Supercritical CO₂ favored the formation of the helical conformation of sPS in lower temperature range and the all trans planar conformation in higher temperature range, instead of forming the latter one only in higher temperature range in ambient atmosphere. However, increasing aPS content in the blends pushed the range for forming the helical conformation to lower temperature and made the all trans planar conformation dominant in aPS/sPS 25/75 blend after treating in supercritical CO₂ above 60 °C. The all trans planar zigzag conformation was more favorable than the helical conformation after mixing aPS in sPS in supercritical CO₂. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 1755–1764, 2007     

Synthesis of graft copolymers with “V‐shaped” and “Y‐shaped” side chains via controlled radical and anionic polymerizations

A combination of nitroxide‐mediated radical polymerization and living anionic polymerization was used to synthesize a series of well‐defined graft (co)polymers with “V‐shaped” and “Y‐shaped” branches. The polymer main chain is a copolymer of styrene and p‐chloromethylstyrene (PS‐co‐PCMS) prepared via nitroxide‐mediated radical polymerization. The V‐shaped branches were prepared through coupling reaction of polystyrene macromonomer, carrying 1,1‐diphenylethylene terminus, with polystyryllithium or polyisoprenyllithium. The Y‐shaped branches were prepared throughfurther polymerization initiated by the V‐shaped anions. The obtained branches, carrying a living anion at the middle (V‐shaped) or at the end of the third segment (Y‐shaped), were coupled in situ with pendent benzyl chloride of PS‐co‐PCMS to form the target graft (co)polymers. The purified graft (co)polymers were analyzed by size exclusion chromatography equipped with a multiangle light scattering detector and a viscometer. The result shows that the viscosities and radii of gyration of the branched polymers are remarkably smaller than those of linear polystyrene. In addition, V‐shaped product adopts a more compact conformation in dilute solution than the Y‐shaped analogy. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 4013–4025, 2007     

Determination of formic and acetic acids in air by piezoelectric microweighing

The quantitative and kinetic parameters of sorption of formic and acetic acids on thin films of various modifiers of piezoelectric quartz resonator electrodes are determined. Parameters of film formation on the electrodes (application procedure and thickness) are optimized. Methods for joint and separate determination of formic and acetic acids in air by piezoelectric microweighing with single- and double-sensor devices are developed.     

Synthesis and characterization of liquid crystalline side‐chain block copolymers containing luminescent 4,4′‐bis(biphenyl)fluorene pendants

A series of new liquid crystalline homopolymers, copolymers, and block copolymers were polymerized from styrene‐macroinitiator ( SMi ) and methacrylates with pendent 4,4′‐bis(biphenyl)fluorene ( M1 ) and biphenyl‐4‐ylfluorene ( M2 ) groups through atom transfer radical polymerization (ATRP). The number‐average molecular weights (Mn) of polymers P1 ‐ P4 were 10,007, 14,852, 6,275, and 10,463 g mol^?1 with polydispersity indices values of 1.21, 1.15, 1.31, and 1.22, respectively. All polymers exhibit the nematic phase. The thermal, mesogenic, and photoluminescent properties of all polymers were investigated. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 4564–4572, 2007