Ionic conductivity of multiarm star polymer/LiClO4 electrolytes

A series of polymer electrolytes based on multiarm polymers and lithium salt complexes were characterized by Fourier transform infrared spectroscopy (FTIR), differential scanning calorimetry (DSC), and impedance measurement. The relationships of conductivity with salt concentration, temperature, and arm numbers are discussed. It is suggested that the star polymer has a higher solvency and ion transfer ability on lithium salts than on linear polymers. The conductivity maximum appeared at a higher salt concentration ([EO]/[Li] = 4). Impedance measurement suggested that the optimum conductivity was 2 × 10^?4 s · cm^?1. The conductivity increased with temperature and the dependence of ionic conductivity on temperature fits the Arrhenius equation. Among the studied systems, the star polymer with a five arm number performs better than other structures. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 4195–4198, 2004     

Detection of Pb2+ using a hydrogel swelling microcantilever sensor.

Hydrogels containing benzo-18-crown-6 were used to modify microcantilevers for measurements of the concentration of Pb2+ in aqueous solutions. These microcantilevers undergo bending deflection upon exposure to solutions containing various Pb2+ concentrations as the result of a swelling of the hydrogels. It was found that a concentration of 10(-6) M Pb2+ can be detected using this technology. Other cations, such as Na+, have no effect on the deflection of this cantilever. The cation K+, which also complexes with benzo-18-crown-6, could interfere with Pb2+ detection, but only at high concentrations (> 10(-4) M).     

A Quantum Chemical Study on Recognition of Nitro-phenols by Calix[n]arenes

A PM3 calculation in vacuum of the inclusion complexation ofo-, m-, p-nitro-phenol with calix[n]arenes is performedsuccessfully. The pathways for inclusion process are describedand the most probable structures of the 1:1 complex are soughtthrough a potential energy scan. The energy differences betweenthe inclusion complexes and the hosts, by calculation, show thatthe most stable complexation is calix[4]-p-nitro phenol andcalix[6]-m-nitro phenol.     

0.8W/80K直线驱动斯特林制冷机的研制

介绍了一种 0 .8W/ 80 K分置式斯特林制冷机。该制冷机采用当前国外先进的直线电机驱动 ,双活塞对称布置结构。该制冷机已通过军品所要求的环境试验 ,输入功率小于 4 0 W(DC)情况下 ,其 +6 0℃高温环境下制冷量≥ 0 .5 W/ 80 K ,带载 0 .5 W工况下 MTTF已突破 2 0 0 0小时。文中主要论述了其工作原理、结构特点、试验情况。     

(Nd_(1-x)Er_x)_2Co_(15.5)V_(1.5)的结构转变与磁性

利用电弧熔炼制备了 (Nd1 xErx) 2 Co1 5 5V1 5(x=0— 1 0 )化合物样品 .通过x射线衍射分析和磁性测量研究了Er替代Nd2 Co1 5 5V1 5中的Nd时对化合物结构和磁性的影响 .研究结果表明 ,低Er含量 (x <0 4 ) ,化合物为Th2 Zn1 7型结构 ;高Er含量时 (x >0 5 ) ,化合物转变为Th2 Ni1 7结构 ;Er含量为x =0 4和 0 5时 ,两种结构共存 .两种结构的晶胞参数a ,c和晶胞体积V随着Er含量的增加都呈现递减的趋势 .随着Er含量的增加 ,(Nd1 xErx) 2 Co1 5 5V1 5化合物的居里温度和饱和磁化强度都单调下降 .(Nd1 xErx) 2 Co1 5 5V1 5化合物的室温各向异性由低Er含量时的易锥型转变为高Er含量时的易轴型 .x =0— 0 5的化合物在温度升高时发生自旋重取向转变 ,自旋重取向温度Tsr随Er含量的增加而减小     

交通灯控制下城市主干道双车道多速元胞自动机交通流模型研究

提出一个城市主干道双车道多速元胞自动机交通流模型，此模型采用开放性 边界条件，在考虑诸多实际因素影响情况下，研究了主干道中车站的设置、交通灯绿信比对 车流量和车流速度的影响.计算机模拟所得到的基本图（流量 速度图）能较好地反映在交 通灯控制下城市主干道交通流真实状况. 关键词： 元胞自动机模型 交通流 主干道     

基于径向基函数神经网络的Lorenz混沌系统滑模控制

针对受参数不确定和外扰影响的混沌Lorenz系统，提出一种基于径向基函数（RBF）神经网 络的滑模控制方法.基于被控系统在不稳定平衡点处状态误差的可控规范形，设计滑模切换 面并将其作为神经网络的唯一输入.单入单出形式的RBF控制器隐层只需7个径向基函数，网 络的权值则依滑模趋近条件在线确定.仿真表明该控制器对系统参数突变和外部干扰具有鲁棒性，同时抑制了抖振. 关键词： 混沌控制 滑模 径向基函数神经网络 Lorenz系统     

一种改进的自适应模糊阈值图象分割方法

自适应模糊阈值图象分割方法的关键和困难在于隶属函数窗宽的自动调整和阈值搜索范围的确定.依靠图象灰度的统计特性初步确定阈值搜索范围，提出了一种改进方法，进而得到隶属函数的窗宽.实验表明这种方法避免了确定图象灰度直方图峰位置的困难，对较低亮度图象分割效果良好.     

用楔形柱面光纤微透镜耦合的1.3μm SOA组件

运用激光模式耦合理论分析了半导体光放大器(SOA)与单模通信光纤的连接损耗,并设计制作了楔形柱面光纤微透镜用来实现两者的模斑匹配,有效地降低了器件的光耦合损耗.本文介绍了楔形柱面光纤微透镜耦合的1.3 μm半导体光放大器(SOA)组件及其制作方法.该组件的最大增益不小于14 dB,其偏振灵敏度小于1 dB,增益波动不大于0.5 dB.     

In-time motion adjustment in laser cladding manufacturing process for improving dimensional accuracy and surface finish of the formed part

This paper presents in-time motion adjustment in laser cladding manufacturing process as a means to improve dimensional accuracy and surface finish of the built part. Defects occurring during laser cladding degrade the part quality such as dimensional accuracy and surface finish. In this paper, in-time motion adjustment strategy was presented to remedy and eliminate defects occurring during laser cladding to improve the dimensional accuracy and surface finish. Based on the relationship between the motion of laser head relative to the growing part and other parameters in effects on clad profile, the laser traverse speed, stand-off distance and laser approach orientation to the existing clad layer were adjusted by instructions from a close-loop control system in real time to remedy and eliminate defects. The results of the experiments verified the effects of in-time motion adjustment on dimensional accuracy and surface finish.