Preparation,thermal properties,and flame retardance of epoxy–silica hybrid resins

A novel epoxy system was developed through the in situ curing of bisphenol A type epoxy and 4,4′‐diaminodiphenylmethane with the sol–gel reaction of a phosphorus‐containing trimethoxysilane (DOPO–GPTMS), which was prepared from the reaction of 9,10‐dihydro‐9‐oxa‐10‐phosphaphenanthrene‐10‐oxide (DOPO) with 3‐glycidoxypropyltrimethoxysilane (GPTMS). The preparation of DOPO–GPTMS was confirmed with Fourier transform infrared, ¹H and ³¹P NMR, and elemental analysis. The resulting organic–inorganic hybrid epoxy resins exhibited a high glass‐transition temperature (167 °C), good thermal stability over 320 °C, and a high limited oxygen index of 28.5. The synergism of phosphorus and silicon on flame retardance was observed. Moreover, the kinetics of the thermal oxidative degradation of the hybrid epoxy resins were studied. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 2354–2367, 2003     

Correlation between Al2O3 particles and interface of Al-Al2O3 coatings by cold spray

Al-Al₂O₃ composite coatings with different Al₂O₃ particle shapes were prepared on Si and Al substrate by cold spray. The powder compositions of metal (Al) and ceramic (Al₂O₃) having different sizes and agglomerations were varied into ratios of 10:1 wt% and 1:1 wt%. Al₂O₃ particles were successfully incorporated into the soft metal matrix of Al. It was found that crater formation between the coatings and substrate, which is typical characteristic signature of cold spray could be affected by initial starting Al₂O₃ particles. In addition, when the large hard particles of fused Al₂O₃ were employed, the deep and big craters were generated at the interface between coatings and hard substrates. In the case of pure soft metal coating such as Al on hard substrate, it is very hard to get proper adhesion due to lack of crater formation. Therefore, the composite coating would have certain advantages.     

Catalytic allylic transfer reactions of functionalized aldehydes promoted by BINOL-Ti(IV) with synergistic reagent

Practical and efficient catalytic asymmetric allylic transfer reactions of tin reagents promoted by BINOL-Ti[OCH(CF₃)₂]₂ complex by the utilization of t-BuSBEt₂ are successful with a variety of functionalized aldehydes containing ketone, aldehyde, ester, amide, or carbamoyl functionality and affords products in high levels of enantioselectivity.     

Effects of physical aging on yielding kinetics of polycarbonate

The purpose of this work was to investigate the effects of physical aging on the kinetics of yielding in polycarbonate. PC samples were annealed over a wide range of aging times and temperatures. Both tensile and compressive tests were performed over various loading rates and temperatures to analyze the effects of aging time and aging temperature on yielding kinetics. Two grades of polycarbonate, Makrolon, of different molecular weights, PC-2608 (low M_w), and PC-3208 (high M_w), supplied by Bayer were analyzed. In unaged condition, PC is hard and tough, but after aging, it becomes more brittle. In terms of molecular movement, the yielding process is a thermally activated process involving inter- and intra-molecular motions. The time–temperature dependence of yielding behavior can be separated into two regions. Aging does not affect localized molecular motions of the β process during yielding. Physical aging in PC results in a slower jump rate of the main segments of macromolecules between two equilibrium positions. It reduces the flexibility of the macromolecules and thus, makes the polymer more brittle. Heat aging also causes a decrease of the entropy (ΔS) in polycarbonate, and this decrease is more important when the molecular weight is reduced. Increasing the annealing time and temperature results in a continuous reduction of ΔS. The rate of aging decreases with decreasing annealing temperature and below about 30 °C, no aging takes place. Annealing also strongly affects the excess of enthalpy in PC. However the effect of physical aging on yielding differs to that on enthalpy excess. The kinetics of yielding and aging processes in polycarbonate are also different. An increase in the strain rate does not have the same effect on the yield stress as an increase in the aging time by a same factor.     

Optical characterization of CdTe/ZnSe fractional monolayer structures grown by atomic layer epitaxy

Luminescence properties of CdTe/ZnSe fractional monolayer grown by atomic layer epitaxy have been investigated. To investigate the origin of the highly efficient luminescence, various optical spectroscopic methods such as, photoluminescence (PL), temporal/spatial resolved PL, temperature dependence PL, and excitation power dependence PL have been used. It is found that structural inhomogeneities affect dominant influence on the line width and line shape of luminescence. The luminescence intensity greatly enhanced by the localization of exciton at the disorder induced localized states.     

Investigation of chemometric calibration performance based on different chemical matrix and signal-to-noise ratio.

The chemometric calibration performance was systematically investigated by two parameters (changing the chemical matrix as well as the signal-to-noise ratio) of the NIR (near-infrared) spectrum. Three different analytes (hexane, cyclohexane, toluene) were selected and heptane was used as a solvent. The degree of spectral difference significantly affected the calibration performance. The largest structural difference between the analyte and the solvent provided the best calibration result for a given signal-to-noise ratio. Additionally, the signal-to-noise ratio of the spectra also directly influenced the calibration performance. Overall, the spectral difference and signal-to-noise ratio were the major factors for governing the chemometric calibration performance, especially in the low-concentration range.     

Low-order modeling and dynamic characterization of rapid thermal processing

A low-order model of rapid thermal processing (RTP) of semiconductor wafers is derived. The first-principles nonlinear model describes the static and dynamic thermal behavior of a wafer with approximate spatial temperature uniformity undergoing rapid heating and cooling in a multilamp RTP chamber. The model is verified experimentally for a range of operating temperatures from 400° C to 900° C and pressures of 1 Torr and 1 atmosphere in an inert N₂ environment. Theoretical predictions suggest model validity over a still wider range of operating conditions. One advantage of the low-order model over previous high-order and statistical models is that the proposed model contains a small number of fundamental parameters and functions that, if necessary, are easily identifiable. Furthermore, because of reduced computational complexity, the low-order model can be used in real-time predictive applications including signal processing and process control design. In studying and verifying the model, the dynamic behavior of a semiconductor wafer undergoing rapid temperature changes is characterized. Close comparison between theory and experiment in terms of the wafer eigenvalue and dc gain is demonstrated; the strong nonlinear effects of temperature are shown. Convective heat transfer losses are also examined and are shown to increase with radial position on the wafer.     

Behaviors of the positive temperature coefficient of resistance of poly(styrene‐co‐n‐butylacrylate) filled with Ni‐plated core‐shell polymeric particles

Conductive composite films of poly(styrene‐co‐n‐butylacrylate) copolymers filled with low‐density, Ni‐plated core‐shell polymeric particles were prepared and their behaviors of positive temperature coefficient of resistance (PTCR) were investigated. When the conductive fillers in the composite film were loaded beyond the critical volume, 10 up to 25 vol %, composite films exhibited a unique electrical resistant transition behavior, which the electrical resistance rapidly increased by several orders of magnitude at the critical temperature. The PTCR transition temperature, in general, occurred before the glass transition temperature of polymer matrix. Further increased the conductive filler loading to 30 vol %, the overpacked conduction paths were formed in the entire composite and the PTCR effects became blurred. While the composite film treated with thermal cycle several times from room temperature up to 120 °C, the electrical resistivity increased accompanied with the shift of the PTCR transition to lower temperature. The reason might have been caused by the formed interfacial cracks within the composite film. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 322–329, 2007     

Irradiation-induced reduction and luminescence properties of Sm doped in BaBPO5

Usually, Sm²⁺ ions could be reduced by heating the materials in reducing atmospheres. Exposure to ionizing radiations is also known to cause Sm³⁺→Sm²⁺ conversion. In this work, BaBPO₅ doped with the samarium ion was prepared by high temperature solid-state reaction. Sm²⁺ ions were obtained by two different reduction methods, i.e., heating in H₂ reduced atmosphere and X-ray irradiation. The measurements of X-ray diffraction (XRD), and scanning electron microscope (SEM) were investigated. It is found that the conversion of Sm³⁺→Sm²⁺ is very efficient in BaBPO₅ hosts after X-ray irradiation. Sm²⁺ ions under these two reduction methods exhibit different characteristics that were studied by measurements of luminescence and decay. The results showed that the luminescence properties of Sm²⁺ ions in BaBPO₅ were highly dependent on the sample preparation conditions.     

Palladium-catalyzed C-N bond formation: synthesis of 1-aryl-1H-pyrazoles from β-bromovinyl aldehydes and arylhydrazines

Cyclic and acyclic β-bromovinyl aldehydes are cyclized with an array of arylhydrazines in toluene at 125 °C in the presence of a palladium catalyst and a phosphorus chelating ligand together with NaO^tBu to give 1-aryl-1H-pyrazoles in moderate to good yields.