Solar Photocatalytic Degradation of 4‐Chlorophenol in Kaolinite Catalysts

This research applies semiconductor photocatalysts, which are formed by metal ion exchange on the surface of kaolinite catalyst with cations, to the study of photocatalytic degradation of 4‐chlorophenol. The analysis results of catalyst properties shows that, after sintering at 400 °C, kaolinite catalyst has a particle size of between 10–100 nm indicating the nano level of synthesized catalysts. Under the same condition, kaolinite‐Ag/Zn catalyst works better in degradation efficiency than single kaolinite‐Ag and kaolinite‐Zn catalysts. Kaolinite‐Zn catalyst declines in degradation efficacy after 150 minutes and performs poorer than the other three types of kaolinite catalysts. In the experiments of different amounts of catalysts, when the concentration exceeds 0.1 wt%, utilization of light energy and degradation efficiency will be reduced due to shielding effect. When at different pH values, the higher the pH value, the more OH‐will be released and that is beneficial for reaction with substances and the increase of reaction rate. Finally multivariate analysis proves that there is one determining factor that influences the photocatalytic degradation of 4‐chlorophenol in kaolinite catalysts, named as “the factor with intermediates competition degree,” the one affecting the 4‐CP degradation at different weight percentages that is referred to as the “shielding effect factor.”     

Electron beam coater for reduction of charging in ice-embedded biological specimens using Ti(88)Si(12) alloy.

Biological macromolecules embedded in vitreous ice are known to suffer from charging while being imaged in an electron transmission cryomicroscope. We developed an electron beam coater that deposits conductive films onto the surface of frozen-hydrated specimens. The conductive films help to dissipate charge during electron irradiation of poorly conductive ice-embedded biological samples. We observed significant reduction in charging of ice-embedded catalase crystals suspended over holes in a holey carbon film after coating them with a 30-A-thick layer of an amorphous alloy, Ti(88)Si(12). Images of the crystals after coating showed diffraction spots of up to 3 A resolution.     

Quantitative determination of glucose in blood plasma by homonuclear proton decoupled water attenuation transverse relaxation Carr-Purcell-Meiboom-Gill (WATR-HDCPMG) NMR spectroscopy

Glucose in 5% D₂O/95% H₂O solution was successfully determined quantitatively by measurements of the ¹H NMR peak height (intensity) of the single peaks at δ(¹H) = 5.22 and 4.64 ppm corresponding to the α-D and the β-D-glucose spectrum, respectively. The single peaks were obtained from decoupling of the high field part of the AX spectrum of the α-D- or the β-D-glucose by incorporation of time shared homonuclear decoupling in the WATR-CPMG method (WATR-HDCPMG) without re-attenuation of the water peak. The method was applied to the determination of total glucose in blood plasma from human subjects undergoing oral glucose tolerance test (OGTT) in the teaching hospital. The results compared favorably with those obtained from the standard glucose oxidase method obtained in a hospital pathology laboratory. The accuracy of the results obtained using the WATR-HDCPMG method was within 3.5% of the glucose oxidation method.     

Aqueous two-phase extraction as an effective tool for isolation of geniposide from gardenia fruit

Natural products are normally obtained by organic solvent extraction and many subsequent chromatographic separations. Compounds of interest are often isolated with very low yield and limited purity. An aqueous two-phase extraction process combined with a simple ethanol treatment, for removing excess inorganic salt, has been developed for preparation of geniposide from gardenia. The system was comprised of PE62, a random copolymer composed of 20% ethylene oxide and 80% propylene oxide, KH2PO4 and ethanol. To find optimal conditions, the partition behavior of geniposide under an aqueous two-phase system was investigated. Various factors were considered, including the concentration of salt, the concentration of polymer, the sample loading, and the addition of ethanol. The experimental results demonstrated that increasing salt concentration or decreasing PE62 concentration results in enhancement of the geniposide partition in the salt-rich phase. The addition of ethanol and higher sample loading also promoted the partition efficiency of geniposide. Based on this study, an optimized system containing 5% PE62, 7.5% KH2PO4, and 10% ethanol was tested on a large-scale extraction. A 39.0-g aliquot of final product (in powder form) with 77% purity of geniposide can be effectively extracted from 500 g of gardenia fruit. This process is proved to be useful for industrial application of geniposide preparation.     

Isolation of lysozyme from hen egg albumen using glass fiber-based cation-exchange membranes

In this study, porous glass fiber membranes were coated with monophenyl trimethoxysilane (MPh) and then sulphonated by chlorosulphonic acid to prepare the cation-exchange membranes with sulphonic acid groups. Different MPh-coating times were tested and the properties of the resulting membranes such as contact angle, FTIR spectrum, conductivity, and ion-exchange capacity were measured. It was found that the optimal MPh-coating time was 60 min and the related ion-exchange capacity was 49.5 μequiv./disc. The modified membrane under the optimal MPh-coating condition was adopted for lysozyme isolation. The results were compared with those for the commercial cation-exchange membrane with sulphonic acid groups (ICE 450 unsupported membrane). Although the prepared membrane exhibited less adsorption capacity than ICE 450 unsupported membrane in the batch lysozyme adsorption experiment, it showed lower non-specific binding ratio under higher salt concentration. In the flow process isolating lysozyme from hen egg albumen, the purification effectiveness obtained using the prepared cation-exchange membrane was superior to the ICE 450 unsupported membrane.     

Arylethynylacridines: electrochemiluminescence and photophysical properties

Electrogenerated chemiluminescence (ECL) of six new ethyne-based acridine derivatives (1-6) has been studied. The new acridine derivatives were synthesized by cross-coupling of 9-chloroacridine and corresponding donor-substituted phenylethynes under modified Sonogashira conditions. The donor groups were varied in the order of increasing steric hindrance and donor strength at the donor site. The solution phase photophysical properties and ECL of these compounds were studied comparatively in acetonitrile solvent. The UV-Visible spectra of compounds 1-5 exhibit closely the same maxima. Density functional theory (DFT) has been invoked to analyze and understand the unexpected UV-Visible absorption behavior. Compounds with weak electron donors produce excimer ECL irrespective of steric hindrance at the donor site, while the compound with a stronger donor gives rise to ECL that is blue-shifted with respect to its photoluminescence spectrum. All except one of these compounds also exhibit solid state fluorescence which may be useful for solid state devices such as organic light emitting diodes (OLEDs) and as laser dyes. The observed properties are discussed with reference to the structure of the compounds synthesized.     

Simultaneous determination of Co(II), Cr(VI), Ni(II) and Pb(II) in water by solvent extraction and high-field 1H NMR Spectrometry

A novel analytical approach is described that combines the preconcentration power of solvent extraction with the resolution and sensitivity of a 500 MHz ¹H NMR spectroscopic detection method for the quantitative determination of metals. Co(II), Cr(VI), Ni(II) and Pb(II) in water are extracted into chloroform as dithiocarbamate complexes. By decoupling the protons and employing a solvent-induced shift method, the ¹H NMR spectrum containing the dithiocarbamate complexes of Co(II), Cr(VI), Ni(II) and Pb(II) is fully resolved at CDCl₃/ C₆D₆ below 40%/60%. The detection limits for Co(II), Cr(VI), Ni(II) and Pb(II) are estimated to be 0.12, 0.073, 0.11 and 0.27 μg/mL, respectively, in the sample solution. Received: 31 July 1997 / Revised: 24 October 1997 / Accepted: 31 October 1997     

Dioxomolybdenum(VI) complexes containing 1-alkyl-2-ethyl-3-hydroxy-4-pyridin-4(1H)-ones

Dioxomolybdenum(VI) complexes derived from ethyl maltol (2-ethyl-3-hydroxy-4-pyrone) and 1-alkyl-2-ethyl-3-hydroxy-4-pyridin-4(1H)-ones have been prepared and characterized using physical methods including ¹H- and ¹³C-n.m.r. spectroscopy, i.r., elemental analysis, and X-ray diffraction for the pyrone and 3-methylpyridine pyridinone derivatives. The octahedral complexes have the general formula cis-MoO₂L₂ where L = the deprotonated pyrone or pyridinone ligand.     

Structural, spectroscopic and photoluminescence studies of LiEu(WO4)2−x(MoO4)x as a near-UV convertible phosphor

A series of lithium europium double tungsto-molybdate phosphors LiEu(WO₄)_2−x(MoO₄)_x (x=0, 0.4, 0.8, 1.2, 1.6, 2.0) have been synthesized by solid-state reactions and their crystal structure, optical and luminescent properties were studied. As the molybdate content increases, the intensity of the ⁵D₀→⁷F₂ emission of Eu³⁺ activated at wavelength of 396 nm was found to increase and reach a maximum when the relative ratio of Mo/W is 2:0. These changes were found to be accompanied with the changes in the spectral feature, which can be attributed to the crystal field splitting of the ⁵D₀→⁷F₂ transition. As the molybdate content increases the emission intensity of the 615 nm peak also increases. The intense red-emission of the tungstomolybdate phosphors under near-UV excitation suggests them to be potential candidate for white light generation by using near-UV LEDs. In this study the effect of chemical compositions and crystal structure on the photoluminescent properties of LiEu(WO₄)_2−x(MoO₄)_x is investigated and discussed.