Behavior of zirconium in the ZrOW(100) system at high temperature, studied by ISS, AES and work-function measurements

The behavior of zirconium atoms at the W(100) surface associated with oxygen adsorption at different sample temperatures has been studied by Auger electron spectroscopy (AES), ion scattering spectroscopy (ISS), and the relative change of the work function (Δф) measured by the onset of the secondary electron energy distribution. The results have revealed: (i) adsorption of zirconium onto the W(100) surface followed by the elevation of the sample temperature up to 1710 K in an oxygen partial pressure of 2.7 × 10⁻⁴ induces complete diffusion of zirconium atoms into the W(100) substrate; (ii) further exposure of oxygen induces co-existence of oxygen and tungsten on the surface at 1710 K, resulting in a work function of 4.37 eV; (iii) keeping the sample temperature at 1710 K, simple evacuation of the system has resulted in surface segregation of zirconium atoms to the surface to form a zirconium atomic layer on the top-most surface, reducing the work function to 2.7 eV. The results have revealed that this specific behavior of zirconium atoms at high temperature assures, with very good reproducibility, the highly stable performance and long service life of Zr---O/W(100)-emitters in practical use, even in a low vacuum of 10⁻⁶ Pa.     

Structure and defects at Y2BaCuO5 interfaces in melt-textured YBa2Cu3Ox superconductors

Y₂BaCuO₅ (211) inclusions are prominent microstructural features found in melt-textured YBa₂Cu₃O_x (123) superconductors. These particles are of interest because the 123/211 interfaces and the interface-associated defects have been proposed to be flux pinning centers. In addition, the 211 particles are believed to be heterogeneous nucleation centers of dislocation which can increase the critical current density of 123. Unfortunately, only limited studies have been performed on these particles to ascertain their roles in flux pinning. In this investigation, 211 particles, the interfacial structure and defects in undeformed and mechanically deformed melt-textured 123 have been studied by transmission electron microscopy. It was found that there appears to be a preferred orientation between large oblong 211 particles and the 123 matrix. In addition, while the 123/211 interfaces in undeformed 123 are sharp and relatively undistorted, the interfaces in deformed 123 samples are much thicker. Also, the distribution of strained regions and dislocations around oblong 211 particles in undeformed 123 is nonuniform; the interfaces of low surface curvature are relatively free of defects while the surfaces of high curvature are abundant in dislocations. In contrast, the 123/211 interfaces in deformed 123 samples contain high density of dislocations regardless of interface curvature.     

用于光学神经网络硬件系统误差纠正的虚拟神经网络

提出了一种用于修正光学神经网络硬件系统误差的虚拟神经网络模型，光学实验结果表明该网络能够有效地消除硬件系统误差对实验结果的影响。     

Ferroelectric polarization switching in nylon-11

Cold-drawn Nylon-11 films, which were prepared by stretching the melt-quenched films to a draw ratio of 2.8: 1 at room temperature, were found to exhibit an electric displacement versus electric field hysteresis loop. The results confirmed that the Nylon-11 film exhibited ferroelectric behavior at or below room temperature. The coercive fields were 65, 98, 125, 160, and 215 MV/m at 20, 0, ?20, ?40, and ?60°C and the remanent polarization at ?20°C (where there was considerably less dc conduction) was 56 mC/m². Switching of the polarization was almost completed within 20 ms.     

Laser-induced breakdown of soda-lime glass microspheres using Nd:YAG laser

The Nd:YAG laser-induced breakdown of 20 μm glass microspheres was investigated using time-resolved optical shadow and Schlieren images. Time-resolved imaging showed the location of the initial breakdown and the shockwave motion over its first 400 μm of expansion. Measured shockwave velocities were in the range of 1–10 km/s and showed a linear dependency on laser fluence within 30 ns.     

Behaviors of the positive temperature coefficient of resistance of poly(styrene‐co‐n‐butylacrylate) filled with Ni‐plated core‐shell polymeric particles

Conductive composite films of poly(styrene‐co‐n‐butylacrylate) copolymers filled with low‐density, Ni‐plated core‐shell polymeric particles were prepared and their behaviors of positive temperature coefficient of resistance (PTCR) were investigated. When the conductive fillers in the composite film were loaded beyond the critical volume, 10 up to 25 vol %, composite films exhibited a unique electrical resistant transition behavior, which the electrical resistance rapidly increased by several orders of magnitude at the critical temperature. The PTCR transition temperature, in general, occurred before the glass transition temperature of polymer matrix. Further increased the conductive filler loading to 30 vol %, the overpacked conduction paths were formed in the entire composite and the PTCR effects became blurred. While the composite film treated with thermal cycle several times from room temperature up to 120 °C, the electrical resistivity increased accompanied with the shift of the PTCR transition to lower temperature. The reason might have been caused by the formed interfacial cracks within the composite film. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 322–329, 2007     

Chemical Speciation of Amphoteric Ions on Semi‐Dry Scrubber Residue and Bag‐House Ash from MSWI

Two series of size‐fractionated combusted residues, a bag‐house ash and a scrubber residue, from a municipal solid waste incinerator (MSWI) were prepared and extracted by means of sequential chemical extraction (SCE) procedures proposed by Tessier. Concentrations of water‐soluble phase, exchangeable phase, carbonated phase, Fe/Mn oxide phase, organic matter phase, and residual phase bound amphoteric metals (Pb and Zn) were obtained, and have been compared with those of single batch extraction of toxic characteristic leaching procedure (TCLP). In each size fraction of baghouse ash or scrubber residue, lead or zinc shows a common phenomena that the TCLP value is always lower than the content of the water‐soluble fraction. For lead, baghouse ash has a significant size‐dependent distribution on the water‐soluble phase to perform a size‐dependent test of lead in the TCLP test. The zinc TCLP data having less size dependence might be due to that neither the baghouse ash nor the scrubber residue has a size‐dependent distribution on the water‐soluble zinc phase.     

Irradiation-induced reduction and luminescence properties of Sm doped in BaBPO5

Usually, Sm²⁺ ions could be reduced by heating the materials in reducing atmospheres. Exposure to ionizing radiations is also known to cause Sm³⁺→Sm²⁺ conversion. In this work, BaBPO₅ doped with the samarium ion was prepared by high temperature solid-state reaction. Sm²⁺ ions were obtained by two different reduction methods, i.e., heating in H₂ reduced atmosphere and X-ray irradiation. The measurements of X-ray diffraction (XRD), and scanning electron microscope (SEM) were investigated. It is found that the conversion of Sm³⁺→Sm²⁺ is very efficient in BaBPO₅ hosts after X-ray irradiation. Sm²⁺ ions under these two reduction methods exhibit different characteristics that were studied by measurements of luminescence and decay. The results showed that the luminescence properties of Sm²⁺ ions in BaBPO₅ were highly dependent on the sample preparation conditions.