A simple and green analytical method for determination of glyphosate in commercial formulations and water by diffuse reflectance spectroscopy

This article describes a simple, inexpensive, and environmentally friendly method for the monitoring of glyphosate using diffuse reflectance spectroscopy. The proposed method is based on reflectance measurements of the colored compound produced from the spot test reaction between glyphosate and p-dimethylaminocinnamaldehyde (p-DAC) in acid medium, using a filter paper as solid support. Experimental designs were used to optimize the analytical conditions. All reflectance measurements were carried out at 495 nm. Under optimal conditions, the glyphosate calibration graphs obtained by plotting the optical density of the reflectance signal (AR) against the concentration were linear in the range 50-500 μg mL(-1), with a correlation coefficient of 0.9987. The limit of detection (LOD) for glyphosate was 7.28 μg mL(-1). The technique was successfully applied to the direct determination of glyphosate in commercial formulations, as well as in water samples (river water, pure water and mineral drinking water) after a previous clean-up or pre-concentration step. Recoveries were in the ranges 93.2-102.6% and 91.3-102.9% for the commercial formulations and water samples, respectively.     

Thiophene‐cored 2,2‐bis(methylol)propionic acid dendrimers for optical‐power‐limiting applications

The synthesis and characterization of dendron‐coated 2,5‐bis(phenylethynyl)thiophene chromophores are described. The dendrimers were grown divergently on the arylthiophene core with the versatile anhydride of 2,2‐bis(methylol)propionic acid. The arylthiophene core was synthesized with Sonogashira coupling reactions. Structurally well‐defined dendrimers up to the fourth generation were grown, as confirmed by size exclusion chromatography, NMR, and matrix‐assisted laser desorption/ionization time‐of‐flight analysis. The different dendritic substitution did not influence the absorption spectra of the compounds in or near the visible region. Solutions of arylthiophenes had good transparency at wavelengths greater than 400 nm. The dendritic thiophenes exhibited an optical‐power limit at the laser wavelength of 532 nm. However, the magnitude of the optical‐power limit of these compounds was slightly lower than that of a nondendritic arylthiophene with n‐pentyl substituents. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 1177–1187, 2005     

Gap effect on moiré patterns

Résumé Nous analysons les caractéristiques principles des lignes de moiré produitues par des réseaux, dont les deux plans ne coïncident pas, illuminés par la lumière diffuse et non cohérente.Nous étudions, les aspects physiques de la formation des lignes de moiré et obtenons des équations qui donnent les valeurs des déformations fictives produites par la non-coïncidence des plans du réseau témoin et du réseau déformé.Les résultats théoriques sont comparés avec les mesures expérimentales. L'écart constaté entre les deux valeurs correspond aux erreurs expérimentales.     

Physicochemical aspects of novel surfactantless, self-templated mesoporous SnO2 thin films

A novel method of synthesis consisting of the production of ordered arrangements of tubular pores distributed inside SnO2 annealed thin films, which are prepared from a rotating disk process carried out at 2000-3500 rpm, is herein described. The main novelty is that no surfactant molecules are required in order to create these ordered pore structures; the templating entities are supramolecular assemblies of oligomeric chains formed during the extra-long aging allowed to the sol-gel processing of tin(IV) tetra-tert-amiloxide, Sn(OAm(t))4, chelated with acetylacetone molecules. Low angle X-ray diffraction peaks of SnO2 thin films calcined at 500 degrees C clearly certify the existence of ordered mesostructures when employing the right H2O/Sn(OAm(t))4 molar ratio during the SnO2 sol-gel synthesis. The final SnO2 ordered mesostructures are reminiscent of those linked to MCM-41 and SBA-15 substrates. Pore-size distribution analyses proceeding from N2 sorption isotherms at 76 K on the SnO2 thin films calcined at 500 degrees C unequivocally confirm the presence of tubular mesopores (mode pore sizes ranging from 5 to 7 nm). The thicknesses of the SnO2 films range from 80 to 150 nm after performing a drying process at 100 degrees C and from 70 to 125 nm after calcining in air at 500 degrees C; these film thicknesses show, in general, decreasing trends when either the spinning rate or the H2O/(Sn(OAm(t))4 ratio is increased.     

Study of mass consistency LES/FDF techniques for chemically reacting flows

A hybrid large eddy simulation/filtered density function (LES/FDF) approach is used for studying chemically reacting flows with detailed chemistry. In particular, techniques utilised for ensuring a mass consistent coupling between LES and FDF are discussed. The purpose of these techniques is to maintain a correct spatial distribution of the computational particles representing specified amounts of fluid. A particular mass consistency technique due to Y.Z. Zhang and D.C. Haworth (A general mass consistency algorithm for hybrid particle/finite-volume PDF methods, J. Comput. Phys. 194 (2004), pp. 156–193) and their associated algorithms are implemented in a pressure-based computational fluid dynamics code suitable for the simulation of variable density flows, representative of those encountered in actual combustion applications. To assess the effectiveness of the referenced technique for enforcing LES/FDF mass consistency, two- and three-dimensional simulations of a temporal mixing layer using detailed and reduced chemistry mechanisms are carried out. The parametric analysis performed focuses on determining the influence on the level of mass consistency errors of parameters such as the initial number of particles per cell and the initial density ratio of the mixing layers. Particular emphasis is put on the computational burden that represents the use of such a mass consistency technique. The results show the suitability of this type of technique for ensuring the mass consistency required when utilising hybrid LES/FDF approaches. The level of agreement of the computed results with experimental data is also illustrated.     

Zero‐valent Iron Nanoparticles Modified Screen‐printed Electrode for FIA or HPLC Amperometric Detection of Metronidazole in Pharmaceutical Formulations

A zero‐valent iron nanoparticles modified electrode was employed as an amperometric detector in flow conditions to determine metronidazole and 2‐methyl‐5‐nitroimidazole in pharmaceutical formulations. Flow injection analysis at ?0.6 V (vs. Ag) achieved limits of detection of 2 and 6 μM for metronidazole and 2‐methyl‐5‐nitroimidazole, respectively, but the analysis was not discriminative between the two compounds. When reverse phase high performance liquid chromatography was applied previous to the electrochemical detection both analytes could be analysed simultaneously. However, the limits of detection slightly increased (10 μM) as a consequence of the use of an organic solvent and a lower sample volume. The relative standard deviation of analytical repeatability was <4.0 % in both techniques. The methods were validated by comparing the results obtained from the analysis of commercial samples with those provided by HPLC‐DAD and no significant differences were detected. Results probed that the modified electrode was a successful tool in the FIA and HPLC analysis of nitro compounds.     

High-performance liquid chromatographic separation of rolipram, bupivacaine and omeprazole using a tartardiamide-based stationary phase influence of flow rate and temperature on the enantioseparation

Chromatographic separation of the chiral drugs rolipram, bupivacaine and omeprazole on a tartardiamide-based stationary phase commercially named Kromasil CHI-TBB is shown in this work. The effect of temperature on the chromatographic separation of the chiral drugs using the Kromasil CHI-TBB stationary phase was determined quantitatively so as to contribute toward the design for the racemic mixtures of the named compound by using chiral columns. A decrease in the retention and selectivity factors was observed, when the column temperature increased. Van't Hoff plots provided the thermodynamic data. The variation of the thermodynamic parameters enthalpy and entropy are clearly negative meaning that the separation is enthalpy controlled.     

Production of slow protonium in vacuum

We descrbe how protonium, the quasi-stable antiproton-proton bound system, has been synthesized following the interaction of antiprotons with the molecular ion in a nested Penning trap environment. From a careful analysis of the spatial distributions of antiproton annihilation events in the ATHENA experiment, evidence is presented for protonium production with sub-eV kinetic energies in states around n = 70, with low angular momenta. This work provides a new two-body system for studies using laser spectroscopic techniques.      

Hydrogen embrittlement assisted by ball-milling to obtain AlCuFe nanoparticles

In this work, we show that the synthesis of AlCuFe nanoparticles can be achieved by a wet ball-milling process. The AlCuFe intermetallic system is highly sensitive to the environmental embrittlement mechanism. Taking advantage of this, the wet ball-milling was used to increase the rate of grinding and accelerate the characteristic cleavage fracture of these phases. This research was carried out by subjecting Al₆₄Cu₂₄Fe₁₂ pre-alloyed ribbons to high-energy ball-milling under different powder–humidity relationships. The pre-alloyed and milled powders were characterized using scanning electron microscopy (SEM), X-ray diffraction (XRD), and scanning transmission electron microscopy (STEM). High resolution electron microscopy (HREM) measurements and energy-dispersive X-ray spectroscopy (EDXS) elemental chemical mapping confirm that the nanoparticles have a BCC structure with Al–Cu–Fe chemical composition. During the wet ball-milling, the aluminum content in the ψ-phase diminishes due to embrittlement mechanism which provokes its aperiodic disarrangement. This aluminum loss could be related with a ψ–β transformation.