Modeling of the defect structure in dislocation-free silicon single crystals

A mathematical model of the formation of primary grown-in microdefects on the basis of dissociation diffusion is presented. Cases of “vacancy-oxygen” (V + O) and “carbon-interstitial” (C + I) interaction near the crystallization front are considered for dislocation-free Si single crystals grown by the floating-zone and Czochralski methods. The approximate analytical expressions obtained by setting 1D and 2D temperature fields in a crystal are in good agreement with the heterogeneous mechanism of formation of grown-in microdefects.     

Powerful pulsed neutron sources for research with a pulsed magnetic field

The prospects for neutron investigations into the magnetic properties of condensed matter with the use of powerful pulsed neutron sources [Japan Spallation Neutron Source (JSNS) (Tokai, Japan), TIRAN (Zababakhin All-Russia Research Institute of Technical Physics, Russian Federal Nuclear Center, Snezhinsk, Russia), Large Hadron Collider (LHC) (CERN)] and pulsed magnetic fields are considered. It is demonstrated that the diffraction measurements of the magnetic states induced by a magnetic field of up to 700–1000 kOe can be performed at the TIRAN reactor and the neutron source that can be developed on the basis of the LHC accelerator.     

Similar quartz crystallographic textures in rocks of continental earth’s crust (by neutron diffraction data): II. Quartz textures in monophase rocks

The types of quartz textures found in a large collection of multiphase rocks from different regions of the earth are analyzed. Crystallographic textures of granulite, amphibolite, slate, and gneiss samples are measured, classified, and compared with the similar textures of monomineral rocks.     

Temperature factor effect on the structure of the separated flow within a supersonic gas stream

The effect of the temperature factor, that is, the ratio of the body temperature to the freestream stagnation temperature, on the structure of the separated flow formed in the presence of a concave corner in a supersonic stream is studied. The strong influence of the temperature factor on the separation zone length and the flow-generated aerodynamic characteristics is established. It is shown that for fairly large deflection angles this flow cannot be described by free interaction, or triple deck, theory.     

Effect of the incomplete accommodation of the heterogeneous recombination energy on heat fluxes to a quartz surface

Taking both the heterogeneous catalytic processes, including the surface formation of particles with excited internal degrees of freedom, and the processes of multicomponent diffusion and heat transfer in the MESOX apparatus fully into account makes it possible to obtain a recombination coefficient and an accommodation coefficient of the oxygen-atoms-on-quartz recombination energy which are in good agreement with the experimental data. The heterogeneous catalysis model constructed can be used effectively for predicting the heat fluxes to the surface of reentry vehicles on their entry into the Earth’s atmosphere.     

Synthesis and structure of nanocrystalline La0.50Ba0.50MnO3

Nanocrystalline manganite La_0.50Ba_0.50MnO₃ was synthesized by the soft-chemical method. For this purpose, the sol-gel method was modified and improved. A trihydric saturated alcohol, e.g., glycerol, was suggested as a new organic matrix. The crystal structure of the composite was studied by X-ray powder diffraction at room temperature. A La_0.50Ba_0.50MnO₃ powder annealed in air at T = 500°C is characterized by a perovskite-like cubic structure with the unit-cell parameter a = 3.869 Å. The chemical composition of the sample was studied by electron-probe X-ray microanalysis. The La: Ba: Mn cation ratio in the material was 1: 1: 2. The surface topography was examined with a scanning electron microscope. The crystallite size was ～30 nm. The dependence of the crystal structure and the surface topology on the annealing temperature was studied. The high-temperature treatment in air resulted in the growth of larger, micrometer-size, crystallites.     

Fatigue Loading and Life Prediction in Three Fretting Fatigue Fixtures

Three fixtures for conducting laboratory fretting fatigue tests are described and their respective testing methods and the results of the analysis are compared. Each of these fixtures has been used to investigate the effects of various parameters of interest in fretting fatigue. These fixtures include a unique apparatus in which all load applied to the specimen is transferred to the fretting pads, an apparatus similar to many found in the literature where partial load transfer occurs across the pads, and a simplified dovetail fixture in which the clamping load, P, and the shear load, Q, are varied in phase. Select test conditions from prior experiments performed on identical material and resulting in similar lives ranging from one to ten million cycles from these fixtures are identified. The various testing conditions were used to compute the unique stress field for each case. The resulting contact stresses were used to calculate crack initiation based criteria, and to calculate stress intensity factors. The three fixtures were shown to be able to accommodate a range of loads, fretting pad contours, and specimen geometries that produced a variety of stress fields. A crack-initiation-based criterion was shown to predict the failure lives of thinner specimens accurately. The stress intensity factor calculations showed the possibility of a crack arresting for a stress field that decays rapidly and the possibility of a local minimum for K as a function of depth. The fixtures are shown to be complementary in generating data for development of robust fretting fatigue models that use these criteria.     

Micro-mechanical behaviors of SMA composite materials under hygro-thermo-elastic strain fields

An analytical procedure to evaluate the behavior of shape memory alloy (SMA) composite under hygrothermal environment is presented. The SMA wires are considered as inclusions embedded in a homogeneous matrix medium of the composite. The inhomogeneity associated with the phase transformation and thermal strains in the SMA wire as well as the hygrothermal strain in the matrix is homogenized using Eshelby’s equivalent inclusion method. In the present work, a similar approach adopted for SMA composites by Marfia and Sacco [Marfia, S., Sacco, E., 2005. Micromechanics and homogenisation of SMA-wire-reinforced materials. J. Appl. Mech. 72 (2), 259–268.] is considered in order to validate the response of SMA composite subjected to thermo-elastic strain field. However, in the present approach, certain modifications and new derivations for the inelastic strain tensors is carried out. First, the constitutive laws for the SMA wire and matrix are expressed in terms of the average strain in the composite. The evolutionary equations used to characterize the pseudoelastic (PE) behavior of the SMA wire are redefined in terms of the eigen strains (phase transformation and thermal strains) occurring in the SMA wire, which are then expressed in terms of the average strain in the composite. Further, the SMA composite constitutive law under coupled hygro-thermo-elastic strain fields is proposed. The generic homogenized hygric and thermal inelastic composite tensors required for the proposed hygro-thermo-elastic constitutive law are derived. Finally, the SMA composite lamina is characterized using Eshelby’s equivalent inclusion method. Using the proposed modifications and derivations, the analytical results are validated for the case of thermo-elastic strain fields and the procedure is then extended to evaluate the SMA composite behavior under hygro-thermo-elastic strain fields. The results include the effect of thermo-elastic and hygro-thermo-elastic strains on the transformation stresses and the nature of hysteresis due to hygric and thermo-elastic strains.     

Mathematical simulation of the evaporation in operation area of a bubble evaporator

Simulation of evaporation in operation area of an evaporator is considered. We obtained a formalized model of this process and optimum conditions of an engineering system on the basis on the analysis.