Capacitive-discharge-heated anisotropic pyrolytic graphite furnace used for atomic absorption spectrometry Part 2. Experimental Verification of Temperature Distribution of the Furnace Surface and of the Gas Phase

The predictions of a theoretical model, embodied in a computer program, describing the heating characteristics of the furnace surface and the gas phase of an anisotropic pyrolytic graphite furnace heated by the capacitive discharge technique are compared with the experimental results obtained by optical pyrometry and by two-line atomic absorption spectrometry, respectively. The surface temperature gradient around the circumference of the type 1 furnace and along the optical axis of the type 3 furnace are calculated and compared with the measured temperatures. The weighted-average of the theoretically predicted gas temperature is in reasonable agreement with the effective vapour temperature measured by two-line atomic absorption method. The heating rate of the furnace does not have a significant effect on the temperature distribution of either the furnace surface or the gas phase. The effect of the difference in the temperature distribution of the type 1 and type 3 furnaces on the atomic absorption signals is also discussed.     

Automated multi-attribute method sample preparation using high-throughput buffer exchange tips

Rationale

The multi-attribute method (MAM) has become a valuable mass spectrometry (MS)-based tool that can identify and quantify the site-specific product attributes and purity information for biotherapeutics such as monoclonal antibodies (mAbs) and fusion molecules in recent years. As we expand the use of the MAM at various stages of drug development, it is critical to enhance the sample preparation throughput without additional chemical modifications and variability.

Methods

In this study, a fully automated MAM sample preparation protocol is presented, where rapid desalting in less than 15 minutes is achieved using miniaturized size-exclusion chromatography columns in pipette tips on an automated liquid handler. The peptide samples were analyzed using an electrospray ionization (ESI) orbitrap mass spectrometer coupled to an ultra-high-performance liquid chromatography (UHPLC) system with a dual column switching system.

Results

No significant change was observed in product attributes and their quantities compared with manual, low-artifact sample preparation. The sample recovery using the buffer exchange tips was greatly enhanced over the manual spin cartridges while still demonstrating excellent reproducibility for a wide variety of starting sample concentrations. Unlike a plate desalting system, the individual columns provide flexibility in the number of samples prepared at a time and sample locations within plates.

Conclusions

This automated protocol enables the preparation of up to 96 samples with less “at-bench” time than the manual preparation of a smaller batch of samples, thereby greatly facilitating support of process development and the use of the MAM in quality control.

     

Preparation and characterization of molecularly imprinted electropolymerized carbon electrodes

Molecularly imprinted polymers (MIPs) selective for fluorescein, rhodamine or 2,4-dichlorophenoxyacetic acid (2,4-D) were electropolymerized onto graphite electrodes using an aqueous solution equimolar in resorsinol/ortho-phenylenediamine and in the presence of the template molecule. For the dyes, the MIP-coated electrodes showed higher affinity for their template molecule than for a non-template dye. The 2,4-D-MIP-coated electrode showed a concentration dependent response for 2,4-D as compared to the polymer-coated electrode prepared in the absence of template molecule.     

Generic serial and parallel on-line direct-injection using turbulent flow liquid chromatography/tandem mass spectrometry

The development of turbulent flow chromatography (TFC) has enabled considerable growth in the utility of on-line direct-injection technologies. TFC has now become established in a large number of varied analytical environments, particularly drug discovery/pharmacokinetics, metabolite profiling, combinatorial library purification, pre-clinical and clinical GLP applications. The utility of turbulent flow technology for in-house pre-clinical and clinical quantitative applications has necessitated extensive valve-cleaning procedures, and consequently lengthy cycle-times, to effectively remove the system carry-over. In-house requirements for assay validation require carry-over less than 20% of the lowest level of quantification (LLOQ), corresponding to 0.02% carry-over for a linear calibration range incorporating 3 orders. A generic turbulent flow chromatography protocol has been developed for drug discovery that incorporates polymeric turbulent flow extraction (cyclone) with C18-based reverse-phase chromatography. Further, multiple wash steps are incorporated within the methodology to meet in-house requirements for carry-over. Selection of novel switching-valve materials based on polyarylethyl ketone (PAEK) and Hastelloy/Valcon E autosampler injection hardware has enabled us to significantly impact the cycle-time required to reduce carry-over. Consequently, optimal usage of switching valves has enabled parallel operation for a generic on-line direct-injection methodology to successfully reduce the total cycle-time. Overall reductions from 4 min per sample to 90 s per sample are shown with comparable data quality using a proprietary target molecule from 0.1-100 ng/mL. This paper describes the hardware configuration and methodologies utilized to perform generic serial and parallel on-line direct-injection using a Turboflow HTLC 2300 system.     

Reactions of a carbene stabilised indium trihydride complex, [InH3{CN(Mes)C2H2N(Mes)}] Mes = mesityl,with transition metal complexes

The reactivity of the carbene stabilised indium trihydride complex, [InH₃(IMes)] IMes = 1,3-dimesitylimidazol-2-ylidene, toward a variety of transition metal complexes has been investigated. The study has shown that the InH₃ complex can act as a carbene and/or hydride transfer reagent to transition metal centres but does not yield heterobimetallic materials. Two new complexes, [Cp₂Ti(-Cl)₂Zn(IMes)Cl] and [CpNi(H)(IMes)], have resulted from this work, both of which have been spectroscopically and structurally characterised.     

Monotone path systems in simple regions

A monotone path system (MPS) is a finite set of pairwise disjoint paths (polygonal areas) in thexy-plane such that every horizontal line intersects each of the paths in at most one point. A MPS naturally determines a pairing of its top points with its bottom points. We consider a simple polygon in thexy-plane wich bounds the simple polygonal (closed) regionD. LetT andB be two finite, disjoint, equicardinal sets of points ofD. We give a good characterization for the existence of a MPS inD which pairsT withB, and a good algorithm for finding such a MPS, and we solve the problem of finding all MPSs inD which pairT withB. We also give sufficient conditions for any such pairing to be the same.The first author's research is supported by the Natural Sciences and Engineering Research Council of Canada     

Stories about groups and sequences

The main theme of this article is that counting orbits of an infinite permutation group on finite subsets or tuples is very closely related to combinatorial enumeration; this point of view ties together various disparate stories. Among these are reconstruction problems, the relation between connected and arbitrary graphs, the enumeration of N-free posets, and some of the combinatorics of Stirling numbers.Dedicated to Hanfried Lenz on the occasion of his 80th birthday.