A new approach to qualitative analysis of organophosphorus pesticide residues in cucumber using a double gas chromatographic system: GC-pulsed-flame photometry and retention time locking GC-mass spectrometry

A qualitative method for the screening of organophosphorus pesticides (OPs) that could present in different types of vegetables has been established and validated. A typical multi-residue extraction procedure of OPs using ethyl acetate and sodium sulphate has been applied. No clean-up was required after extraction, and concentrated extracts were analysed by gas chromatography with pulsed-flame photometric detection (GC-PFPD). Confirmation of compound identities was performed by gas chromatography with mass spectrometric detection (GC-MSD) in the electron impact (EI) mode with full scan acquisition. Retention time locking (RTL) software was used in order to improve the method capability of identification and confirmation. Spiked samples at pesticide concentrations equal to the maximum residue level (MRL) were used to check chromatographic performance and for validation studies. The proposed method allows a rapid and accurate identification of the studied OPs until the ng ml(-1) range for those whose use is forbidden, and above their MRL concentration for the rest.     

Simple and rapid determination of the drug naproxen in pharmaceutical preparations by heavy atom-induced room temperature phosphorescence

A simple, selective and sensitive heavy atom-induced room temperature phosphorimetric method (HAI-RTP) is described for the determination of naproxen (NAP) in pharmaceutical preparations. The phosphorescence signals are a consequence of intermolecular protection when analytes are, exclusively, in presence of a heavy atom salt and sodium sulfite as an oxygen scavenger to minimize RTP quenching. These variables selection constitute the basis of a HAI-RTP method for the determination of naproxen (detection limit 17.6 ng ml(-1); 1.71% relative standard deviation at 250 ng ml(-1)). The method has been applied satisfactorily to the analysis of pharmaceutical preparations.     

Highly enantioselective Cu-catalysed asymmetric 1,4-addition of diphenylzinc to cyclohexenone

Highly enantioselective Cu-catalysed 1,4-addition of diphenylzinc to cyclohexenone has been achieved for the first time using a monodentate phosphoramidite ligand.     

Stabilization of cobalt(II) chloro-complexes with the butanediammonium cation

Summary Cobalt(II) chlorocomplexes with empirical formulae (bnH₂)₂CoCl₆·2H₂O (1) and (bnH₂)₂CoCl₆ (2), where bnH ₂ ²⁺ represents the diprotonated species of putrescine (1,4-butanediamine), were prepared.The visible spectra in the solid state and measurement of the magnetic moments permit the assignation of an octahedral geometry for cobalt in (1) and a tetrahedral geometry for (2).     

Determination of molybdenum, chromium and aluminium in human urine by electrothermal atomic absorption spectrometry using fast-programme methodology

Rapid and direct procedures for the determination of molybdenum, chromium and aluminium in human urine samples are developed. Fast-programme methodology is used to simplify the heating cycles. Hydrogen peroxide, nitric acid and Triton X-100 are added to the urine samples which are directly introduced into the furnace. For molybdenum, two successive injection steps are required due to the low level of this element in the samples analyzed. Calibration is carried out using aqueous standards for aluminium and the standard additions method for both molybdenum and chromium. The reliability of the procedures is checked by analyzing two certified reference materials.     

Determination of pesticides in waters by capillary gas chromatography with atomic emission detection

Capillary gas chromatography with atomic emission detection (GC-AED) was successfully used to separate and quantify 14 pesticides (organochlorines, organophosphorus compounds and pyrethrins) in water samples after liquid-liquid extraction with ethyl acetate. Monitoring the emission lines for elements such as chlorine, bromine and sulfur ensures nearly specific chromatograms for these elements, and markedly increases selectivity. Calibration curves were obtained by plotting peak area versus concentration and the correlation coefficients relating to linearity were at least 0.999. Each chromatographic separation takes 21 min and, since two injections are necessary, it requires approximately 1 h to analyze one sample. The method shows a precision of 4.3-8.2% (RSD), depending on the compound. The application of liquid-liquid extraction with ethyl acetate led to recoveries from spiked samples ranging from 76 to 113%. The sensitivity and linearity for the elements chlorine, sulfur, nitrogen and phosphorus were checked under the optimized conditions at their customary emission wavelength. The sensitivity and linearity for these compounds decreased in the order (atom and emission wavelength) Cl (479 nm)>S (181 nm)>P (178 nm)>N (174 nm). A study of the GC-AED system's response to chlorine concentration in eight pesticide molecules was performed and a linear relationship was found with a correlation coefficient of 0.987.     

Characterization of three agave species by gas chromatography and solid-phase microextraction-gas chromatography-mass spectrometry

Steam distillation (SD) extraction-solid-phase microextraction coupled to GC-MS was developed for the determination of terpenes and Bligh-Dyer extraction-derivatization coupled with GC for the determination of fatty acids such as ethyl esters were used. It was found that the three different Agave species have the same profile of fatty acids; the quantity of these compounds is different in each Agave variety. On the other hand, different terpenes were identified in the three Agave plants studied: nine in A. salmiana, eight in A. angustifolia and 32 in A. tequilana Weber var. azul.     

TTT Cure Diagram

Curing reactions of the epoxy system consisting of a diglycidyl ether of bisphenol A (BADGE n=0) and m-xylylenediamine (m-XDA) were studied to calculate time-temperature-transformation (TTT) isothermal cure diagram for this system. Gel times were measured as a function of temperature using solubility test. Differential scanning calorimetry (DSC) was used to calculate the vitrification times. DSC data show a one-to-one relationship between T _g and fractional conversion, a independent of cure temperature. As a consequence, T _g can be used as a measure of conversion. The activation energy for the polymerization overall reaction was calculated from the gel times obtained using the solubility test (41.5 kJ mol^-1). This value is similar to the results obtained for other similar epoxy systems. Isoconversion contours were calculated by numerical integration of the best fitting kinetic model. This revised version was published online in July 2006 with corrections to the Cover Date.     

Crystallization kinetic studies: A means to evaluate time-temperature-transformation curves. Application to metallic glasses

It is shown that the study of the kinetics of crystallization of an amorphous alloy may be used to obtain the correct form of the low temperature part of the time-temperature-transformation (T-T-T) curves. A unified review of the current kinetics of crystallization studies is presented and the general kinetic equation which gives the reaction rate as a function of temperature and crystalline fraction is shown to contain information related to theT-T-T-curves. Finally examples of application to two metallic glasses, Nd₃Fe₇₇B₂₀ and Fe_67.5Co₁₅Nb_1.5B₁₆, obtained by rapid solidification techniques are presented. The comparison between theory and experiment is satisfactory.

---

Zusammenfassung Es wird gezeigt, daß die Untersuchung der Kristallisationskinetik von amorphen Legierungen genutzt werden kann, die korrekte Form des Niedertemperaturbereiches der Zeit-Temperatur-Transformation (T-T-T) Kurven zu erhalten. Es wird ein einheitlicher Überblick über die jüngsten Untersuchungen von Kristallisationskinetiken gegeben und an der allgemeinen Gleichung der Reaktionsgeschwindigkeit als eine Funktion von Temperatur und Kristallanteil wird gezeigt, daß sie Informationen bezüglich der T-T-T-Kurven beinhaltet. Letztlich wird eine Anwendung an zwei, durch schnelles Erstarren gewonnenen metallischen Gläsern Nd₃Fe₇₇B₂₀ und Fe_67.5Co₁₅Nb_1.5B₁₆ dargelegt. Zwischen Theorie und Praxis konnte eine ausreichende Übereinstimmung festgestellt werden.

---

---

Dedicated to Professor Dr. H. J. Seifert on the occasion of his 60^th birthday

---

This work was supported by the Comision Interdepartamental de Cienca y Tecnologia, CICYT (project No. MAT88-0439) which are acknowledged.     

A new anode material LiMoS2 for use in rechargeable Lithium Ion Batteries

The novel applications of molybdenum disulfide in recent research were reviewed, such as in lubricant, catalyst and photoelectrochemical solar cells. Recently, we found that LiMoS2 is a good candidate for new anode materials for lithium ion batteries with high lithium storage capacity.Here, the anode material LiMoS2 was synthesized by a hydrothermal method at 150℃ and the electrochemical characterization as an anode material for lithium ion batteries was examined.put in Teflon-lined stainless steel autoclaves of capacity 40 mL. Distilled water was used to fill the autoclaves to 70 % of the total volume. The autoclaves were maintained at 150℃ for 24 h and then cooled naturally. The resulting dark-gray powders were filled and washed with distilled water,diluted hydrochloric acid and ethanol, successively. The final products were dried at 80℃ for 24 h.The powder X-ray diffraction pattern showed the prepared LiMoS2 was amorphous structure. A test cell using LiMoS2 as the active material was discharged and charged between 3 and 0.01 V with respect to Li metal at a constant current density of C/5 (that is, one lithium per formula unit in 5 hours). During the first discharge, the potential rapidly drops to reach a large plateau at 2.2 V, then slowly drops to the other plateau at 0.8 V, and then continuously decreases down to 0.01V. There is only a plateau at 1.35 V in the subsequent discharge curves. The plateaus of charge potential appear at about 1.9 V.The irreversible loss was 41% in the first cycle. The ratio of discharge and charge is more than 99%in the subsequent cycles. Moreover, the ratio of discharge and charge almost reaches 100% after thedemonstrated that LiMoS2 has a very high capacity and a good cycle-ability as an anode material forlithium ion batteries.