Miscibility of bisphenol-A polycarbonate with poly(methyl methacrylate)

The miscibility of bisphenol-A polycarbonate (PC) with poly(methyl methacrylate) (PMMA) has been reexamined using differential scanning calorimetry (DSC) and optical indications for phase separation on heating, i.e., lower critical solution temperature (LCST) behavior. Various methods have been used to prepare the blends including methylene chloride (CH₂Cl₂) and tetrahydrofuran (THF) solution casting, melt mixing, and precipitation of PC and PMMA simultaneously from THF solution by using the nonsolvents methanol and heptane. It is shown that the resulting phase behavior for PC/PMMA blends is strongly affected by the blend preparation method. However, these blends are miscible over the whole blend composition range (unambiguous single composition-dependent T_g's and LCST behavior) when prepared by precipitation from solution using heptane as the nonsolvent. To the contrary, solution-cast and melt-mixed PC/PMMA blends were all phase separated, which may be attributed to the “solvent” effect and LCST behavior, respectively, not discovered in previous reports. Methanol precipitation does not lead to fully mixed blends, which demonstrates the importance of the choice of nonsolvent when using the precipitation method.     

Semi‐analytical integration of the 8‐node plane element stiffness matrix using symbolic computation

The semi‐analytical integration of an 8‐node plane strain finite element stiffness matrix is presented in this work. The element is assumed to be super‐parametric, having straight sides. Before carrying out the integration, the integral expressions are classified into several groups, thus avoiding duplication of calculations. Symbolic manipulation and integration is used to obtain the basic formulae to evaluate the stiffness matrix. Then, the resulting expressions are postprocessed, optimized, and simplified in order to reduce the computation time. Maple symbolic‐manipulation software was used to generate the closed expressions and to develop the corresponding Fortran code. Comparisons between semi‐analytical integration and numerical integration were made. It was demonstrated that semi‐analytical integration required less CPU time than conventional numerical integration (using Gaussian‐Legendre quadrature) to obtain the stiffness matrix. © 2005 Wiley Periodicals, Inc. Numer Methods Partial Differential Eq, 2006     

Effects of sodium salicylate on the febrile response and increased levels of cyclic AMP in cerebrospinal fluid during endogenous pyrogen-induced fever in rabbits

To further evaluate the causality between endogenous pyrogen (EP)-induced fever and cyclic adenosine-3',5'-monophosphate (cyclic AMP) level, the effects of sodium salicylate (SS) on the febrile response and increased levels of cyclic AMP in both cerebrospinal fluid (c.s.f.) and plasma during EP-induced fever in rabbits were observed. The results suggest that cyclic AMP is probably involved in the central mediation of EP-induced fever and that increased concentration of cyclic AMP in c.s.f. associated with EP-induced fever is not the result of temperature elevation but appears to be caused by the increased synthesis in the central nervous system. In addition it is confirmed that blood is impossibly a contributory source of increased cyclic AMP in c.s.f. during EP fever, and that SS may act subsequent to the increase in cyclic AMP.     

Development of a quantitative FI-MS technique for the characterization of high- and nonboiling saturated hydrocarbon mixtures

Summary Using a saturated non-boiling hydrocarbon mixture, the influence of two parameters on the results of field ionization mass spectrometry (FI-MS) measurements was studied: (a) the potential difference between the FI emitter and the counterelectrode; (b) the emitter temperature.Variation of the potential difference had only a minor effect on the average molecular mass measured and had no evident effect on the relative ring number distribution in the sample. In contrast, when the emitter temperature was increased, higher average molecular masses were recorded. Moreover, the average molecular masses shifted to higher ring numbers. In order to control the relationship between the described influences during mixture analysis, measuring instructions have been developed that enable the quantitative analysis of unknown saturated samples. However, average molecular mass of the mixture must be known.

---

Entwicklung einer quantitativen FI-MS-Methode zur Charakterisierung von gesättigten hoch- und nichtsiedenden Kohlenwasserstoffgemischen

     

Investigation of multicomponent fluoride optical materials in the UV spectral region: I. Single crystals of Ca1−x R xF2+x (R = Sc, Y, La, Yb, Lu) solid solutions

Crystalline materials that are transparent in the vacuum UV spectral region and currently used have been reviewed. Transmission of crystals of solid solutions with the fluorite structure Ca_1?x R _xF_2+x (R = Sc, Y, La, Yb, Lu) in the UV and vacuum UV spectral regions has been investigated. It is shown that application of different methods of purification of fluorides from some impurities can significantly improve the optical quality of fluoride multicomponent crystals in the short-wavelength spectral region.     

Unsteady motion in single-line flow-injection systems

Unsteady motion in single-line flow-injection systems consisting of n tubular elements with valve or hydrodynamic injection is studied theoretically. A formula for the duration of the initial period of unsteady flow is derived. This initial period is much shorter than the mean residence time of the analyte in practical systems. It can therefore be neglected in mathematical modelling of such systems. Experimental data obtained with single-line systems with valve and hydrodynamic injection confirmed the validity of the theoretical equations.     

Mathematical modelling of the oxidation of nickel titanium alloys

A one-dimensional bulk reaction model for the oxidation of nickeltitanium is formulated, with preferential oxidation of titaniumbeing included. The modelling is directed at the better understandingof the dominant mechanisms involved in the oxidation processand their significance for the biocompatibility of the alloy.Two different regimes for the relative diffusivities of oxygenand the metals are investigated. By assuming fast bulk reactions,different asymptotic structures emerge in different parameterregimes and the resulting models take the form of moving boundaryproblems. Different profiles of nickel concentration are obtained:in particular a nickel-rich layer (observed in practice) ispresent below the oxide/metal interface for the case when oxygenand the metals diffuse at comparable rates.