O′-β′复相Sialon陶瓷中相组成的控制

用Si₃N₄,SiO₂和Al₂O_?作原料,以Y₂O_?为添加剂,研究了O’-β’所在的四个相容性区中组成,于1400—1800℃之间,O’和β’的形成动力学。O’于1400℃开始生成,1600℃达到最大形成量。高于1600℃,O’减少乃至消失。研究发现,O’的这种不稳定性,并非自身热分解的结果。Al含量的增加,液相出现和β’的形成,才是导致O’-Sialon溶解而消失的原因。 此外,认为Si₃N₄-O’(x=0.3)-Y₂Si₂O₇-YAG相容性区,是在制备具有合理的O’-β’平衡相组成的复相陶瓷时,可供实际选用的组成区。     

轻型汽车后桥半轴断裂件的组织及断口特征

采用光学显微镜和扫描电子显微镜等手段，对某轻型汽车40Cr后桥半轴断裂件的组织及断口特征进行了分析结果表明：半轴在调质处理时的淬火温度不够高，使其表层和心部组织中存在较多的铁素体相，造成了工件最终的硬度和疲劳强度不足，导致半轴在使用中发生扭转疲劳断裂．     

Dispersion and distribution of organically modified montmorillonite in nylon‐66 matrix

Nylon‐66 nanocomposites were prepared by melt‐compounding nylon‐66 with an alkyl ammonium surfactant pretreated montmorillonite (MMT). The thermal stability of the organic MMT powders was measured by thermogravimetric analysis. The decomposition of the surfactant on the MMT occurred from 200 to 500 °C. The low onset decomposition temperature of the organic MMT is one shortcoming when it is used to prepare polymer nanocomposites at high melt‐compounding temperatures. To provide greater property enhancement and better thermal stability of the polymer/MMT nanocomposites, it is necessary to develop MMT modified with more thermally stable surfactants. The dispersion and spatial distribution of the organic MMT layers in the nylon‐66 matrix were characterized by X‐ray diffraction. The organic MMT layers were exfoliated but not randomly dispersed in the nylon‐66 matrix. A model was proposed to describe the spatial distribution of the organic MMT layers in an injection‐molded rectangular bar of nylon‐66/organic MMT nanocomposites. Most organic MMT layers were oriented in the injection‐molding direction. Layers near the four surfaces of the bar were parallel to their corresponding surfaces; whereas those in the bulk differed from the near‐surface layers and rotated themselves about the injection‐molding direction. The influence of the spatial distribution of the organic MMT on crystallization of nylon‐66 was also investigated. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 1234–1243, 2003     

Controlled/living polymerization of 2‐(diethylamino)ethyl methacrylate and its block copolymer with tert‐butyl methacrylate by atom transfer radical polymerization

Polymerization of 2‐(diethylamino)ethyl methacrylate (DEAEMA) via homogeneous atom transfer radical polymerization under various reaction conditions is described. The effects of the initiators and solvents were examined. With 1,1,4,7,10,10‐hexamethyl triethylenetetramine/copper(I) chloride/p‐toluenesulfonyl chloride as the ligand/catalyst/initiator system in methanol, poly(DEAEMA) with a polydispersity index as low as 1.07 was synthesized. Kinetic studies demonstrated the polymerization was very well controlled and exhibited the living characteristic of the process. Well‐defined block copolymers of DEAEMA and tert‐butyl methacrylate (tBMA) were successfully synthesized. The copolymers could be synthesized with equally good results by starting with either p(DEAEMA) or p(tBMA) as the macroinitiators. However, only the macroinitiators terminated with chlorine should be used. The corresponding macroinitiators with bromine as a transferable group did not yield well‐defined copolymers. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 2688–2695, 2003     

Crystallographic report: Bis(norfloxacin)dilead(II) tetranitrate, [Pb2(H‐Norf)2(ONO2)4]

The centrosymmetric binuclear structure of [Pb₂(H‐Norf)₂(ONO₂)₄]shows the geometry around each lead(II) atom to be distorted trigonal bipyramidal with Pb–O distances ranging from 2.357(3) to 2.769(4) Å. Copyright © 2003 John Wiley & Sons, Ltd.     

Magnetic resonance imaging and pulsed Doppler sonography of poststenotic jets: Correlation between signal void and flow velocity distribution

To correlate the appearance of poststenotic jets on gradient echo images with features of localized Doppler spectra of the jets, we studied an in vitro model of steady flow-through stenoses of 86, 96, and 99% area reduction. As fluids, water and a 40% glycerol solution in water were used. MRI was performed with a 1.5 T whole body imager and gradient echo images were obtained in planes parallel to the direction of flow. Doppler spectra were acquired separately from the MR measurements at 1 cm intervals for a distance of 10 cm downstream from the stenosis. Poststenotic signal void was observed for water and for the 40% glycerol solution only if the mean velocity within the stenosis exceeded a limit of 50–60 cm/sec. On the MR images, the jets could be divided into two segments: A proximal jet segment of uniform width equal to the diameter of the stenosis, followed by a distal jet segment which was characterized by broadening and then dissipating signal void. Except for the 99% stenosis, a high signal intensity core was present within the proximal jet segment. In the proximal jet segment, the Doppler measurements showed a low temporal fluctuation of the maximal flow velocity and only little flow opposite to the main flow direction. In the distal jet segment, the velocity fluctuation and the intensity of reverse flow increased sharply. The high signal intensity core of the jet was associated with a poststenotic zone of constant maximal flow velocity. The results demonstrate a close relationship between characteristic features of poststenotic jets in MRI and pulsed Doppler sonography.     

等厚双层涂层材料受集中力作用的平面问题理论解

界面应力的正确评价是分析薄膜涂层材料力学特性的难题之一。利用镜像点法和Dirichlet等值性原理，本文推导了等厚双层薄膜涂层材料受表面集中力作用的平面问题理论解。该显式理论解是以固定在各镜像点上的局部坐标系下的Goursat应力函数的形式给出的。对应于高阶镜像点的应力函数，可通过递推的方法，从对应于低阶镜像点的应力函数求得，而且也易于计算机编程。随着镜像点阶数的增大，它与界面的距离也越来越大，因而相对应的应力函数对界面应力的影响越来越小。最后的算例表明，只需考虑前面有限个镜像点，便可获得足够精度的解。该理论解可作为格林函数，以求解复杂问题的理论解，也可用作边界元法的基本解，提高数值计算的精度和效率。     

Ferromagnetic Properties of Bond-Dilution and Random Positive or Negative Uniaxial Anisotropy Blume-Capel Model

We study the ferromagnetic properties of spin-1 system, which is considered in the frame of the bond dilution and random positive or negative anisotropy Blume-Capel model in the effective field theory and a cutting approximation. The investigation of phase diagrams displays some rich properties of the trajectory of tricritical point, reentrant henomena at low temperatures. Under certain both bond concentrations and random negative anisotropy, there are new transition lines of double tricritical points. So special emphasis is placed on the influence of the bond dilution and random anisotropy on phase diagrams. The magnetizations of the system are also discussed. Some results have not been evealed in previous reports.     

Boiling heat transfer characteristics of nanofluids in a flat heat pipe evaporator with micro-grooved heating surface

An experimental study was performed to understand the nucleate boiling heat transfer of water–CuO nanoparticles suspension (nanofluids) at different operating pressures and different nanoparticle mass concentrations. The experimental apparatus is a miniature flat heat pipe (MFHP) with micro-grooved heat transfer surface of its evaporator. The experimental results indicate that the operating pressure has great influence on the nucleate boiling characteristics in the MFHP evaporator. The heat transfer coefficient and the critical heat flux (CHF) of nanofluids increase greatly with decreasing pressure as compared with those of water. The heat transfer coefficient and the CHF of nanofluids can increase about 25% and 50%, respectively, at atmospheric pressure whereas about 100% and 150%, respectively, at the pressure of 7.4 kPa. Nanoparticle mass concentration also has significant influence on the boiling heat transfer and the CHF of nanofluids. The heat transfer coefficient and the CHF increase slowly with the increase of the nanoparticle mass concentration at low concentration conditions. However, when the nanoparticle mass concentration is over 1.0 wt%, the CHF enhancement is close to a constant number and the heat transfer coefficient deteriorates. There exists an optimum mass concentration for nanofluids which corresponds to the maximum heat transfer enhancement and this optimum mass concentration is 1.0 wt% at all test pressures. The experiment confirmed that the boiling heat transfer characteristics of the MFHP evaporator can evidently be strengthened by using water/CuO nanofluids.     

L-型域上Toeplitz算子代数的广群结构

讨论L-型域上Toeplitz C^*-代数C^*(Ω)所对应广群G的拓扑结构.用Euclid空间加法闭子群的分类方法对G的单位空间M_∞的拓扑结构进行了详细刻画。