Immobilization of catalase on membranes of poly(ethylene)-g-co-acrylic acid and poly(tetrafluoroethylene)-g-co-acrylic acid and their application in hydrogen peroxide electrochemical sensors

The immobilization of catalase on grafted membranes of poly(ethylene)-g-co-acrylic acid and poly(tetrafluoroethylene)-g-co-acrylic acid and their application in hydrogen peroxide electrochemical sensors is described. The introduction of carboxylic acid groups onto a hydrophobic support provides a good environment for subsequent enzyme immobilization. This single membrane, hydrogen peroxide sensor showed significant improvement with respect to the double membrane versions. The response is very rapid, the linear range being from 10 μM up to 6 mM, with a detection limit of 4.7 μM, and a lifetime of more than 4 months.     

Mössbauer study of small amounts of iron in graphite,around the diamond-graphite pressure-temperature stability region

An exploratory Mössbauer spectroscopy study of the Fe-C system in the C rich region, prepared by high pressure-high temperature treatment near the graphite-diamond stability line, was made. The results obtained for the different processing conditions give no evidence of Fe intercalation in graphite. The presence of some water in the cell produced hydrated Fe complexes, which can explain the deleterious effect of water or hydrogen in the high pressure diamond synthesis.     

Carrier diffusion in InGaAs/GaAs quantum wells grown on vicinal GaAs(0 0 1) substrates

We have investigated the influence of vicinal GaAs substrates on the optical and electronic properties of InGaAs/GaAs quantum wells (QWs). A single In_0.10Ga_0.90As QW was grown by molecular-beam epitaxy on a vicinal GaAs(0 0 1) substrate with a miscut angle of 0° (nominal), 2°, 4° and 6° towards [1 1 0]. The carrier diffusion was obtained by a micro-photoluminescence scan technique that permits to observe the effective diffusion length characterized by the lateral spread of carriers in the QW followed by radiative recombination. The carrier diffusion length was obtained parallel (L_||) and perpendicular (L) to the atomic steps. The diffusion length decreases as the temperature increases up to 100 K. Above this temperature we found different behaviours that depend on the sample miscut angle.     

Geometric modeling of homoepitaxial CVD diamond growth: I. The {1 0 0}{1 1 1}{1 1 0}{1 1 3} system

Plasma-assisted CVD homoepitaxial diamond growth is a process that must satisfy many stringent requirements to meet industrial applications, particularly in high-power electronics. Purity control and crystalline quality of the obtained samples are of paramount importance and their optimization is a subject of active research. In the process of such studies, we have obtained high purity CVD diamond monocrystals with unusual morphologies, namely with apparent {1 1 3} stable faces. This phenomenon has led us to examine the process of CVD diamond growth and build up a 3D geometrical model, presented here, describing the film growth as a function of time. The model has been able to successfully describe the morphology of our obtained crystals and can be used as a predictive tool to predetermine the shape and size of a diamond crystal grown in a given process configuration. This renders accessible control of desirable properties such as largest usable diamond surface area and/or film thickness, before the cutting and polishing manufacture steps take place. The two latter steps are more sensitive to the geometry of the growth sectors, which will be addressed in a companion paper.Our model, applicable to the growth of any cubic lattice material, establishes a complete mapping of the final morphology state of growing diamond, as a function of the growth rates of the crystalline planes considered, namely {1 0 0}, {1 1 1}, {1 1 0}, and {1 1 3} planes, all of which have been observed experimentally in diamond films. The model makes no claim as to the stability of the obtained faces, such as the occurrence of non-epitaxial crystallites or twinning. It is also possible to deduce transient behavior of the crystal morphology as growth time is increased. The model conclusions are presented in the form of a series of diagrams, which trace the existence (and dominance) boundaries of each face type, in presence of the others, and where each boundary crossing represent a topology change in terms of number of faces, edges and vertices. We validate the model by matching it against crystals published in the literature and illustrate its predictive value by suggesting ways to increase usable surface area of the diamond film.     

Simultaneous determination of cloramphenicol, salicylic acid and resorcinol by capillary zone electrophoresis and its application to pharmaceutical dosage forms

This study demonstrates the separation of active ingredients in acne formulations (salicylic acid, cloramphenicol and resorcinol in presence of azulene) by capillary zone electrophoresis. Factors affecting their separations were the buffer pH and concentration, applied voltage, sample preparation, and presence of additives. Optimun results were obtained with a 50 mM sodium tetraborate-50 mM sodium phosphate, pH 9.0. The carrier electrolyte gave baseline separation with good resolution, short migration times (<6 min), great reproducibility and accuracy. Calibration plots were linear over at least three orders of magnitude of analyte concentrations, the lower limits of detection being within the range 0.39-1.25 μg ml⁻¹. The procedure was fast and reliable and commercial pharmaceuticals could be analysed without prior sample clean-up procedure.     

Hydroformylation: a versatile tool for the synthesis of new β-formyl-metalloporphyrins

Formyl derivatives of protoporphyrin-IX dimethyl ester metal complexes were obtained via hydroformylation reactions, catalysed by rhodium-triphenylphosphine complexes. The regioselectivity of the reaction is remarkably dependent on the metal centre of the porphyrin, yielding 100% of the branched aldehyde with zinc(II) complexes and 75% with the nickel(II). The NMR characterisation of the new compounds was carried out after their derivatisation into acetals.     

Analysis and finite element simulations of a second‐order fluid model in a bounded domain

This article is concerned with the equations governing the steady motion of a viscoelastic incompressible second‐order fluid in a bounded domain. A new proof of existence and uniqueness of strong solutions is given. In addition, using appropriate finite element methods to approximate a coupled equivalent problem, sharp error estimates are obtained using a fixed point argument. The method is applied to the two‐dimensional lid‐driven cavity problem, at low Reynolds number and in a certain range of values of the viscoelastic parameters, to analyze the combined effects of inertia and viscoelasticity on the flow. © 2007 Wiley Periodicals, Inc. Numer Methods Partial Differential Eq, 2007     

Gravitational collapse of a charged and radiating fluid ball in the diffusion limit

The collapse of a charged and radiating ball in the diffusion limit is studied using a method reported by Herrera and collaborators. The interior solution is matched with the exterior Reissner-Nordström-Vaidya metric to obtain a system of differential equations at the surface of the distribution, which can be integrated numerically for some set of initial data. For one model, the profiles of the physical variables are obtained at any piece of the material in terms of Schwarzschild-like coordinates.     

Application of quantum-chemical methods including density functional theory for the interpretation of isotropic hyperfine data. The example of azulenebenzoquinone

The radical anion of aceneazulenedione in which a benzoquinone is fused to an azulene moiety was generated by electrolysis and by reduction with the alkali metals in ethereal solvents. The hyperfine data could not be reproduced by standard Hückel calculations which usually give reliable predictions for the spin distribution in radical ions such as azulene quinones and a variety of extended π systems. However, PPP and, preferably,ab initio geometry optimisations followed by single-point calculations of the Fermi contact interaction with density functional theory, led to a straightforward assignment of the hyperfine coupling constants.