A rapid and sensitive extractive spectrophotometric determination of copper(II) in pharmaceutical and environmental samples using benzildithiosemicarbazone.

Benzildithiosemicarbazone (BDTSC) is proposed as a sensitive and selective analytical reagent for the extractive spectrophotometric determination of copper(II). BDTSC reacts with copper(II) in the pH range 1.0-7.0 to form a yellowish complex. Beer's law is obeyed in the concentration range 0.5-0.4 microg cm(-3). The yellowish Cu(II)-BDTSC complex in chloroform shows a maximum absorbance at 380 nm, with molar absorptivity and Sandell's sensitivity values of 1.63 x 10(4) dm3 mol(-1) cm(-1) and 0.00389 microg cm(-2), respectively. A repetition of the method is checked by finding the relative standard deviation (RSD) (n = 10), which is 0.6%. The composition of the Cu(II)-BDTSC complex is established as 1:1 by slope analysis, molar ratio and Asmus' methods. An excellent linearity with a correlation coefficient value of 0.98 is obtained for the Cu(II)-BDTSC complex. The instability constant of the complex calculated from Edmond and Birnbaum's method is 7.70 x 10(-4) and that of Asmus' method is 7.66 x 10(-4), at room temperature. The method is successfully employed for the determination copper(II) in pharmaceutical and environmental samples. The reliability of the method is assured by analyzing the standard alloys (BCS 5g, 10g, 19e, 78, 32a, 207 and 179) and by inter-comparison of experimental values, using an atomic absorption spectrometer.     

On a question of Gross

Using the notion of weighted sharing of sets we prove two uniqueness theorems which improve the results proved by Fang and Qiu [H. Qiu, M. Fang, A unicity theorem for meromorphic functions, Bull. Malaysian Math. Sci. Soc. 25 (2002) 31-38], Lahiri and Banerjee [I. Lahiri, A. Banerjee, Uniqueness of meromorphic functions with deficient poles, Kyungpook Math. J. 44 (2004) 575-584] and Yi and Lin [H.X. Yi, W.C. Lin, Uniqueness theorems concerning a question of Gross, Proc. Japan Acad. Ser. A 80 (2004) 136-140] and thus provide an answer to the question of Gross [F. Gross, Factorization of meromorphic functions and some open problems, in: Proc. Conf. Univ. Kentucky, Lexington, KY, 1976, in: Lecture Notes in Math., vol. 599, Springer, Berlin, 1977, pp. 51-69], under a weaker hypothesis.     

Diastereoselective formation of 2-aryl-3-arenesulfonyl 4-ethyl-1,3-oxazolidines: An X-ray crystallographic and H NMR study

N-Arylsulfonamides of (R)- and (S)-2-amino-1-butanol, on condensation with aromatic aldehydes produced diastereomerically pure 2-aryl-3-arenesulfonyl 4-ethyl-1,3-oxazolidines. The absolute configurations of one enantiomeric pair have been determined from two fully refined X-ray structures, supplemented by nmr data.     

Quantitative dependence of MR signal intensity on tissue concentration of Gd(HP-DO3A) in the nephrectomized rat.

Cardiac-gated SE 20/224 +/- 20 MR images were obtained from nephrectomized rats before and after intravenously administering 153Gd-Gd(HP-DO3A). The concentration of Gd, [Gd], was linear in dose in myocardium, skeletal muscle, and blood. Under steady-state conditions, where d[Gd]/dt = 0, image intensities (IIN) in regions of interest were compared with the measured [Gd]. IIN was linear in myocardium at less than or equal to 0.61 mumol/g-myocardium (less than or equal to 0.5 mmol/kg dose) and in skeletal muscle at less than or equal to 0.63 mumol/g-muscle (less than or equal to 0.75 mmol/kg). Above 0.6 mumol Gd/g-tissue, IIN did not increase further. The in vivo data were consistent with measured ex vivo and in vivo relaxivities. A 29% greater slope for IIN versus [Gd] in myocardium [14,439 +/- 4350 IIN (mumol/g)] than in muscle [10,258 +/- 5,296 IIN/(mumol/g)] was attributed to a significant difference in blood content: 25% versus 2% weight blood in myocardium and skeletal muscle, respectively. Two components were apparent from plots of ex vivo 1/T1 versus [Gd] in myocardium and muscle, and only one for blood.     

A proof of Howard’s conjecture in homogeneous parallel shear flows

A rigorous mathematical proof of Howard's conjecture which states that the growth rate of an arbitrary unstable wave must approach zero, as the wave length decreases to zero, in the linear instability of nonviscous homogeneous parallel shear flows, is presented here for the first time under the restriction of the boundedness of the second derivative of the basic velocity field with respect to the vertical coordinate in the concerned flow domain.     

Design and operation characteristics of a high power transverse flow pulser sustained cw CO2 laser

A transverse flow, transverse discharge cw CO₂ laser in which de discharge is sustained by employing high repetition rate high voltage pulses has been developed. Pulser sustained discharge through electrodes of innovative design provided uniform excitation at electrical input power densities more than 10 W/cc. Laser output power more than 2.5 kW was obtained in a laser gas mixture consisting of 0.5 mbar of CO₂, 16 mbar of N₂ and 38.5 mbar of He. Design details and operational characteristics of this laser are presented.     

Conductivity and dielectric properties of sol–gel derived porous zirconia

The 8-mol percentage Y₂O₃-stabilized Porous Zirconia was prepared using sol–gel method. Zirconium oxalate gel was prepared by the addition of appropriate amount of oxalic acid solution into the 1 M aqueous solution of zirconium-oxy chloride. A cubic phase zirconia powder was obtained by calcination and milling of the zirconium oxalate gel. Crystallization temperature was found about 450 °C from the Differential thermal analysis. The phase analysis by X-ray diffraction shows the presence of cubic phase. Pellets sintered at 1,350 °C were highly porous, and the electrical conductivity was found with lower value due to the porosity, and the hardness was about 8.0 GPa. Paper presented at the Third International Conference on Ionic Devices (ICID 2006), Chennai, Tamilnadu, India, Dec. 7–9, 2006.     

Melting of heterogeneous vortex matter: The vortex ‘nanoliquid’

Disorder and porosity are parameters that strongly influence the physical behavior of materials, including their mechanical, electrical, magnetic and optical properties. Vortices in superconductors can provide important insight into the effects of disorder because their size is comparable to characteristic sizes of nanofabricated structures. Here we present experimental evidence for a novel form of vortex matter that consists of inter-connected nanodroplets of vortex liquid caged in the pores of a solid vortex structure, like a liquid permeated into a nanoporous solid skeleton. Our nanoporous skeleton is formed by vortices pinned by correlated disorder created by high-energy heavy ion irradiation. By sweeping the applied magnetic field, the number of vortices in the nanodroplets is varied continuously from a few to several hundred. Upon cooling, the caged nanodroplets freeze into ordered nanocrystals through either a first-order or a continuous transition, whereas at high temperatures a uniform liquid phase is formed upon delocalization-induced melting of the solid skeleton. This new vortex nanoliquid displays unique properties and symmetries that are distinct from both solid and liquid phases.     

“Optimization of aircraft maintenance/support infrastructure using genetic algorithms—level of repair analysis”

Level of repair analysis (LORA) is an approach used during the design stage of complex equipment for analysis of the cost effectiveness of competing maintenance strategies. LORA is carried as a part of the life cycle cost and cost of ownership analysis and plays a significant role in minimizing the life cycle cost and cost of ownership of the capital equipment. Since many purchasing decisions of complex equipment are based on cost of ownership, it has become essential to carry out LORA to compete in the market. In this paper, we develop a mathematical model for LORA and propose a solution methodology based on genetic algorithms. The concept is illustrated using a hypothetical aircraft engine.     

Buckling of laminated plates - A simple finite element based on higher-order theory

A four-noded rectangular element with seven degrees of freedom at each node is developed for buckling analysis of laminated plate structures having any number of layers with a constant thickness of individual layers. The displacement model is so chosen that it can explain adequately the parabolic distribution of transverse shear stresses and the non-linearity of in-plane displacements across the thickness. A geometrical stiffness matrix is developed using in-plane stresses. A wide range of plates from thick to thin are examined under uniaxial loading conditions. The results are compared with the existing analytical and numerical solutions. The present formulations confirm its applicability for buckling analysis of a wide range of plates.