Novel fixed‐site–carrier polyvinylamine membrane for carbon dioxide capture

Fixed‐site–carrier membranes were prepared for the facilitated transport of CO₂ by casting polyvinylamine (PVAm) on various supports, such as poly(ether sulfone) (PES), polyacrylonitrile (PAN), cellulose acetate (CA), and polysulfone (PSO). The cast PVAm on the support was crosslinked by various methods with glutaraldehyde, hydrochloric acid, sulfuric acid, and ammonium fluoride. Among the membranes tested, the PVAm cast on polysulfone and crosslinked by ammonium fluoride showed the highest selectivity of CO₂ over CH₄ (>1000). The permeance of CO₂ was then measured to be 0.014 m³ (STP)/(m² bar h) for a 20 μm thick membrane. The effect of the molecular weight of PVAm and feed pressure on the permeance was also investigated. The selectivity increased remarkably with increasing molecular weight and decreased slightly with increased pressure in the range of 1 to 4 bar. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 4326–4336, 2004     

Multiphysical modeling and meshless simulation of electric‐sensitive hydrogels

According to a multiphase mixture theory, we have mathematically developed a multiphysical model with chemoelectromechanical coupling considerations, termed the multieffect‐coupling electric‐stimulus (MECe) model, to simulate the responsive behavior of electric‐sensitive hydrogels immersed in a bath solution under an externally applied electric field. For solutions of the MECe model consisting of coupled nonlinear partial differential governing equations, a meshless Hermite–Cloud method with a hierarchical iteration technique has been used for a one‐dimensional steady‐state analysis of a hydrogel strip. The computed results are compared with the experimental data, and there is very good agreement. Simulations within the domains of both hydrogels and surrounding solutions also present distributions of the ionic concentrations and electric potential as well as the hydrogel displacement. The effects of various physical parameters on the response behavior of electric‐stimulus responsive hydrogels are discussed in detail. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 1514–1531, 2004     

Toughness mechanism in polypropylene composites: Polypropylene toughened with elastomer and calcium carbonate

Polypropylene (PP) was modified with elastomer or CaCO₃ particles of two different sizes (1 μm and 50 nm) in various volume fractions. The dispersion morphology and mechanical properties of the two systems were investigated as functions of the particle size and volume fraction of the modifier. The brittle‐to‐tough transition occurred when the matrix ligament thickness was less than the critical ligament thickness, which was about 0.1 μm for the PP used here, being independent of the type of modifier. At the same matrix ligament thickness, the improvement of the toughness was obviously higher with the elastomer rather than with CaCO₃, but adding CaCO₃ increased the modulus of PP. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 1656–1662, 2004     

Colorimetric recognition of different enzymology-concerning transition metals based on a hybrid cluster complex.

A hybrid cluster complex, formed by chelating a chromogenic ligand to a [2Fe-2S] cluster, sensitively exhibited differential colorimetric responses towards Hg2+, Cd2+, Cr3+, Pb2, Sn2+, Cu2+, Zn2+, Fe3+ and Co2+ in water at physiological pH. Speciation of some of these metal elements, such as Cr(III) and Sn(IV), was also studied by UV/Vis absorption.     

NMR investigation of concentrated alumina and silica slurries

The longitudinal relaxation times (T₁) of water in concentrated silica and alumina slurries were measured as a function of solids content. It was shown that the results could be fit very well with a two-phase fast-exchange model between free and surface-bound water. As expected, values of T₁ for bound water were in the order of 20–2000 times lower than that for free water, indicating a higher effective viscosity of the surface-bound water. The strength of the interaction depended on the particular surface, and all of the aluminas examined interacted more strongly with water than the two silicas studied, which themselves differed considerably. The chemical mechanical polishing (CMP) removal rate of tantalum by silica slurries was shown to be directly correlated with the interaction parameters, derived from the NMR relation times rather than with total surface hydroxyl group concentration.     

光纤光栅选频掺Yb3+双包层光纤激光器

利用相位掩模法 ,在D形内包层掺Yb3 双包层光纤一端直接写制出Bragg光栅 ,用作双包层光纤激光器的输出腔镜 .试验得到了线宽为 0 196nm ,波长为 10 5 8 2nm ,最高输出功率为 5 70mW的稳定激光输出 ,解决了激光器中模式竞争造成的输出不稳定现象 .从速率方程出发 ,对激光器的输出功率与抽运功率、光栅反射率的关系以及最佳光纤长度进行了理论分析 ,结果与实验符合很好     

Baker＇s Yeast Mediated Reduction of Optically Active Diketone

Baker‘s yeast mediated reduction of optically active diketone is described. The two keto groups are efficiently differentiated and the ee value of the recovered material is considerably raised. It affords highly optically active key intermediates efficiently for the synthesis of natural polyhydroxylated agarofuran products.     

Crystal Structures of Two Potential Tumor Imaging Agents and Therapeutic Agents Copper（Ⅱ） Ternary Complexes with Salicylidene-tyrosinato Schiff Base and Nitrogen-donor Chelating Lewis Base

The crystal structures of two potential tumor imaging agents and therapeutic agents -copper(Ⅱ) complexes with salicylidene-tyrosinato Schiff base and nitrogen-donor chelating Lewis base, [Cu(sal-tyr)(bipy)] 1 and [Cu(sal-tyr)(phen)]2CH3OH 2 are presented. Our work is helpful to get deep understanding of novel 64Cu tumor imaging agents and therapeutic agents.     

Stability Conditions of the MMAP [ K ]/ G [ K ]/1/ LCFS Preemptive Repeat Queue

In this paper, we study the stability conditions of the MMAP[K]/G[K]/1/LCFS preemptive repeat queue. We introduce an embedded Markov chain of matrix M/G/1 type with a tree structure and identify conditions for the Markov chain to be ergodic. First, we present three conventional methods for the stability problem of the queueing system of interest. These methods are either computationally demanding or do not provide accurate information for system stability. Then we introduce a novel approach that develops two linear programs whose solutions provide sufficient conditions for stability or instability of the queueing system. The new approach is numerically efficient. The advantages and disadvantages of the methods introduced in this paper are analyzed both theoretically and numerically.     

In-time motion adjustment in laser cladding manufacturing process for improving dimensional accuracy and surface finish of the formed part

This paper presents in-time motion adjustment in laser cladding manufacturing process as a means to improve dimensional accuracy and surface finish of the built part. Defects occurring during laser cladding degrade the part quality such as dimensional accuracy and surface finish. In this paper, in-time motion adjustment strategy was presented to remedy and eliminate defects occurring during laser cladding to improve the dimensional accuracy and surface finish. Based on the relationship between the motion of laser head relative to the growing part and other parameters in effects on clad profile, the laser traverse speed, stand-off distance and laser approach orientation to the existing clad layer were adjusted by instructions from a close-loop control system in real time to remedy and eliminate defects. The results of the experiments verified the effects of in-time motion adjustment on dimensional accuracy and surface finish.