Lipase‐Supported Metal–Organic Framework Bioreactor Catalyzes Warfarin Synthesis

A green and sustainable strategy synthesizes clinical medicine warfarin anticoagulant by using lipase‐supported metal–organic framework (MOF) bioreactors (see scheme). These findings may be beneficial for future studies in the industrial production of chemical, pharmaceutical, and agrochemical precursors.     

Polymer nanoparticles with a sensitive CO2‐responsive hydrophilic/hydrophobic surface

Poly(methyl methacrylate) (PMMA) nanoparticles with a sensitive CO₂‐responsive hydrophilic/hydrophobic surface that confers controlled dispersion and aggregation in water were prepared by emulsion polymerization at 50 °C under CO₂ bubbling using amphiphilic diblock copolymers of 2‐dimethylaminoethyl methacrylate (DMAEMA) and N‐isopropyl acrylamide (NIPAAm) as an emulsifier. The amphiphilicity of the hydrophobic–hydrophilic diblock copolymer at 50 °C was triggered by CO₂ bubbling in water and enabled the copolymer to serve as an emulsifier. The resulting PMMA nanoparticles were spherical, approximately 100 nm in diameter and exhibited sensitive CO₂/N₂‐responsive dispersion/aggregation in water. Using copolymers with a longer PNIPAAm block length as an emulsifier resulted in smaller particles. A higher concentration of copolymer emulsifier led to particles with a stickier surface. Given its simple preparation and reversible CO₂‐triggered amphiphilic behavior, this newly developed block copolymer emulsifier offers a highly efficient route toward the fabrication of sensitive CO₂‐stimuli responsive polymeric nanoparticle dispersions. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2019, 57, 2149–2156     

DFT mechanistic study of the H2‐assisted chain transfer copolymerization of propylene and p‐methylstyrene catalyzed by zirconocene complex

DFT computations have been performed to investigate the mechanism of H₂‐assisted chain transfer strategy to functionalize polypropylene via Zr‐catalyzed copolymerization of propylene and p‐methylstyrene (pMS). The study unveils the following: (i) propylene prefers 1,2‐insertion over 2,1‐insertion both kinetically and thermodynamically, explaining the observed 1,2‐insertion regioselectivity for propylene insertion. (ii) The 2,1‐inserion of pMS is kinetically less favorable but thermodynamically more favorable than 1,2‐insertion. The observation of 2,1‐insertion pMS at the end of polymer chain is due to thermodynamic control and that the barrier difference between the two insertion modes become smaller as the chain length becomes longer. (iii) The pMS insertion results in much higher barriers for subsequent either propylene or pMS insertion, which causes deactivation of the catalytic system. (iv) Small H₂ can react with the deactivated [Zr]?pMS?PP_n facilely, which displace functionalized pMS?PP_n chain and regenerate [Zr]? H active catalyst to continue copolymerization. The effects of counterions are also discussed. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 576–585     

Microelectromechanical Systems for Nanomechanical Testing: Electrostatic Actuation and Capacitive Sensing for High-Strain-Rate Testing

Experimental Mechanics - There have been relatively few studies on mechanical properties of nanomaterials under high strain rates, mainly due to the lack of capable nanomechanical testing devices....     

激光能量对反钙钛矿GaCMn_3薄膜结构与物性的影响

本文采用脉冲激光沉积方法在LaAlO3(001)单晶衬底上制备了反钙钛矿GaCMn3薄膜,通过控制制备过程中脉冲激光的能量,研究了不同激光能量条件对GaCMn3薄膜结构与物理性能的影响.分别利用X射线衍射仪、原子力显微镜、超导量子干涉仪和物理性能测试系统,对所制备的薄膜的晶体结构、表面形貌和磁性、电输运性质进行了研究.结果表明,制备的样品均为具有多个晶面取向的反钙钛矿薄膜,且薄膜结构和物性明显随制备激光能量的变化而变化.当激光能量为450mJ时,制备的薄膜多晶面取向性最弱,结晶性和表面形貌最优良.实验所得的薄膜均表现出顺磁-铁磁-反铁磁相转变,然而转变过程比块材较平缓,同时薄膜的电阻率并未表现出块材中的突变特征,我们推测该现象很可能是由衬底的应力及衬底的晶格膨胀对薄膜反常晶格变化的抑制作用造成的.     

Surface of room temperature ionic liquid [bmim][PF6] studied by polarization- and experimental configuration-dependent sum frequency generation vibrational spectroscopy

Understanding and control of the surface properties such as molecular orientations are of great importance in numerous applications of ionic liquids. However, there remain discrepancies among the previous experimental and theoretical studies on the surface orientation and structures of room temperature ionic liquids(RTIL) systems. In this article, the orientation of 1-butyl-3-methylimidazolium([bmin]) cation at the air/liquid interface of a characteristic RTIL, 1-butyl-3-methylimidazolium hexafluorophosphate([bmim][PF6]), was investigated by the sum frequency generation vibrational spectroscopy(SFG-VS). Detailed polarization and experimental configuration analyses of the SFG-VS spectra showed the possibility of a small spectral splitting in the CH3 symmetric stretching region, which can be further attributed to the probable existence of multiple orientations for the interfacial [bmim] cations. In addition, the(N)–CH3 vibrations were absent, ruling out the prediction by several recent molecular dynamics simulations which state that portions of the [bmim] cations orient with a standing-up(N)–CH3 group at the ionic liquid surface. Hence, new realistic theoretical models have to be developed to reflect the complex nature of the ionic liquid surface.     

QEPAS系统中石英音叉模态仿真计算与研究

对石英音叉增强型光声光谱(QEPAS)系统中常用的石英音叉进行了有限元模态计算，获得石英音叉前6阶振型与模态频率，认知了第4阶对称摆动振型为有效振动，利用单因素法分析了石英音叉的音臂长度l₁、音臂宽度w₁、音臂厚度t、音臂切角θ、音臂圆孔直径d及音臂圆孔高度h对低阶有效共振频率(Fre)的影响，敏感度依次为： l₁> w₁>d>θ>t>h，考虑实际设计情形，筛选出了l₁，w₁，d与h四个石英音叉设计变量，采用Box-Behnken实验设计方案与RSM(response surface methodology)方法，以Fre为函数目标，建立l₁，w₁，d与h的二次回归响应面模型，得到了参数之间的交互作用，利用Design-Expert软件对响应面模型进行设计参数反求，结果表明，在15 000 Hz≤Fre≤25 000 Hz计算区域内误差较小，基本满足QEPAS系统的计算需求，所提出的研究与设计方法具有一定通用性，可为QEPAS系统中石英音叉结构参数设计提供参考。     

Water-induced formation of an alkali-ion dimer in cryptomelane nanorods

Tunneled metal oxides such as α-Mn₈O₁₆ (hollandite) have proven to be compelling candidates for charge-storage materials in high-density batteries. In particular, the tunnels can support one-dimensional chains of K⁺ ions (which act as structure-stabilizing dopants) and H₂O molecules, as these chains are favored by strong H-bonds and electrostatic interactions. In this work, we examine the role of water molecules in enhancing the stability of K⁺-doped α-Mn₈O₁₆ (cryptomelane). The combined experimental and theoretical analyses show that for high enough concentrations of water and tunnel-ions, H₂O displaces K⁺ ions from their natural binding sites. This displacement becomes energetically favorable due to the formation of K²⁺ dimers, thereby modifying the stoichiometric charge of the system. These findings have potentially significant technological implications for the consideration of cryptomelane as a Li⁺/Na⁺ battery electrode. Our work establishes the functional role of water in altering the energetics and structural properties of cryptomelane, an observation that has frequently been overlooked in previous studies.

Water displaces potassium ions and initiates the formation of a homonuclear dimer ion (K²⁺) in the tunnels of hollandite.     

Synthesis,Crystal Structure,and Magnetic Properties of a New Dinuclear Iron Complex with Schiff Base Ligand

A new dinuclear iron(Ⅲ) complex has been synthesized and structurally characterized by X-ray crystallography: [FeⅢ2(L)(C6H5COO)(SO4)(CH3OH)2]·CH3CN·CH3OH(1, H3 L = N,N'-bis(salicylidene)-1,3-diamino-2-propanol). Complex 1 belongs to orthorhombic space group Pna21 with a = 11.4400(8), b = 22.9705(2), c = 12.5712(9) , V = 3303.5(4) 3, Z = 4, F(000) = 1576, Dc = 1.531 g·cm–3, Mr = 761.36, μ = 1.007 mm–1, S = 1.014, the final R = 0.0505 and wR = 0.1018. The crystal packing is stabilized by intermolecular O–H···O hydrogen bonds, forming an extended one-dimensional chain structure. The temperature dependence of magnetic susceptibility measurement shows that antiferromagnetic interaction is propagated between the metal centers. Fit as dinuclear arrangement gave parameters of J = 19.7 cm-1, g = 1.89 and R2 = 0.9999.     

A New Method of Testing and Evaluating the Quality of Refined Montan Wax: Digital Color and GC Fingerprint

To establish a new method of testing and evaluating the quality of refined montan wax (RMW), digital color and GC fingerprint technology were introduced and applied. CIE Lab color mode was used to digitize the exterior colors of RMW, and the score obtained through a fitting function was also used to reflect its quality. It is shown that they were in complete accord with the human visual perception trend. The GC fingerprint was used to characterize the internal chemical information of RMW, and the composition of its internal features was reflected through the relative retention time (RRT) and relative peak area (RPA) values. It is shown that there was a high degree of similarity between the fingerprints, while certain differences also existed. This can be used to implement effective application of RMW to aspects such as quality control, adulteration identification, and origin attributions.