Rapid ion-exchange technique for the separation and preconcentration of chromium(VI) and chromium(III) in fresh waters

A technique for the separation and preconcentration of Cr(VI) and Cr(III) in fresh waters is presented. The analytical procedure involves the use of anion- and cation-exchange columns. The columns are eluted and the eluate is analysed for chromium using a graphite furnace atomic absorption spectrometer. The recovery of Cr(VI) and Cr(III) is 97.86 ± 1.31% and 102.36 ± 1.25% (95% confidence), respectively. The detection limits are 0.019 and 0.020 μg 1^?1 for 200 ml of sample (twice the standard deviation of eleven replicate blanks). The method is rapid and the need for minimum sample handling avoids contamination problems.     

Mechanistic investigations of the ethylene tetramerisation reaction

The unprecedented selective tetramerisation of ethylene to 1-octene was recently reported. In the present study various mechanistic aspects of this novel transformation were investigated. The unusually high 1-octene selectivity in chromium-catalyzed ethylene tetramerisation reactions is caused by the unique extended metallacyclic mechanism in operation. Both 1-octene and higher 1-alkenes are formed by further ethylene insertion into a metallacycloheptane intermediate, whereas 1-hexene is formed by elimination from this species as in other reported trimerisation reactions. This is supported by deuterium labeling studies, analysis of the molar distribution of 1-alkene products, and identification of secondary co-oligomerization reaction products. In addition, the formation of two C6 cyclic products, methylenecyclopentane and methylcyclopentane, is discussed, and a bimetallic disproportionation mechanism to account for the available data is proposed.     

Serial potentiometric and conductometric detection in fast non-suppressed ion chromatography applied to the analysis of filter collected airborne particulates

Non-suppressed ion chromatography (NSIC) has been optimized to permit the determination of chloride, nitrate and sulfate in the low mg/l concentration range within 3 min. Using conductometric detection the extraneous (positive) injection peak was found to adversely affect the early eluting chloride signal when samples with high amounts of total cations are analyzed. The serial arrangement of a downstream potentiometric detector with a chloride ion selective electrode, which does not respond to other alterations of the composition of the eluent than the change in chloride concentrations, is shown to be suitable for interference-free, sensitive and reliable chloride evaluation. Application of the proposed system to the determination of chloride in extracts of filter collected airborne particulates revealed (for those samples that could be evaluated by both detection methods) high precision and no systematic deviations between conductometric and potentiometric detection.Dedicated to Professor Dr. Peter Brätter on the occasion of his 60th birthday     

Polymorphism of paracetamol

The thermodynamic relationship between crystal modifications of paracetamol was studied by alternative methods. Temperature dependence of saturated vapor pressure for polymorphic modifications of the drug paracetamol (acetaminophen) was mea sured and thermodynamic functions of the sublimation process calculated. Solution calorimetry was carried out for the two modifications in the same solvent. Thermodynamic parameters for sublimation for form I (monoclinic) were found: ΔG _sub²⁹⁸=60.0 kJ mol⁻¹; ΔH _sub²⁹⁸=117.9±0.7 kJ mol⁻¹; ΔS _sub²⁹⁸=190±2 J mol⁻¹ K⁻¹. For the orthorhombic modification (form II), the saturated vapor pressure could only be studied at 391 K. Phase transition enthalpy at 298 K, ΔH _tr²⁹⁸(I→II)=2.0±0.4 kJ mol⁻¹, was derived as the difference between the solution enthalpies of the noted polymorphs in the same solution (methanol). Based on ΔH _tr²⁹⁸ (I→II), differences between temperature dependencies of heat capacities of both modifications and the vapor pressure value of form II at 391 K, the temperature dependence of saturated vapor pressure and thermodynamic sublimation parameters for modification II were also estimated (ΔG _sub²⁹⁸=56.1 kJ mol⁻¹; ΔH _sub²⁹⁸=115.9±0.9 kJ mol⁻¹; ΔS _sub²⁹⁸=200±3 J mol⁻¹ K⁻¹). The results indicate that the modifications are monotropically related, which is in contrast to findings recently reported found by classical thermochemical methods.     

Ethylene tetramerization: a new route to produce 1-octene in exceptionally high selectivities

Linear alpha-olefins, such as 1-hexene and 1-octene, are important comonomers in the production of linear low-density polyethylene (LLDPE). The conventional method of producing 1-hexene and 1-octene is by oligomerization of ethylene, which yields a wide spectrum of linear alpha-olefins (LAOs). While there exists several processes for producing 1-hexene via ethylene trimerization, a similar route for the selective production of 1-octene has so far been elusive. We now, for the first time, report an unprecedented ethylene tetramerization reaction that produces 1-octene in selectivities exceeding 70%, using an aluminoxane-activated chromium/((R2)2P)2NR1 catalyst system.     

Characterization of the pores in hydrous ferric oxide aggregates formed by freezing and thawing

Hydrous ferric oxides (HFO) are efficient sorbents for inorganic and organic pollutants and therefore have great potentials in environmental science and engineering applications. Freezing and thawing of HFO suspensions leads to the formation of dense HFO aggregates. It facilitates the handling and increases the drying rate of HFO. In this study, we used a combination of pycnometry, gas adsorption (N(2) gas, water vapor), and small-angle neutron scattering (SANS) to characterize the porosity and pore size distribution of dense HFO aggregates formed by freezing dialyzed HFO suspensions at -25 degrees C and thawing them at room temperature. The crystallinity of the HFO, which was a 2-line ferrihydrite, was not affected by this treatment. Wet sieving and laser diffraction analysis showed that the dense HFO aggregates had a unimodal size distribution with an average diameter of 235+/-35 microm. Increasing the freezing rate by cooling with liquid N(2) (-196 degrees C) resulted in much smaller aggregates with an average diameter of 20 microm. Adding NaNO(3) electrolyte to the HFO suspensions prior to freezing also resulted in the formation of smaller aggregates. The dense HFO aggregates formed at -25 degrees C had a porosity of 0.73+/-0.02 ll(-1). SANS revealed a unimodal size distribution of pores, with an average pore diameter of 2.0 nm. The diameter of the HFO crystallites was estimated by transmission electron microscopy to be 1.9+/-0.5 nm. Geometrical considerations taking into account the unit particle and average pore size suggest that the crystallites retain 1-2 layers of hydration water during the coagulation induced by freezing. Analysis by N(2) gas adsorption showed that drying the dense HFO aggregates induced a reduction in porosity by about 25% and shifted the pore size distribution to smaller diameters. Rewetting during water vapor adsorption did not induce significant changes of the aggregate structure. The specific surface area of the dry HFO aggregates was between 320 and 380 m(2)g(-1).     

Synthesis of a silk-inspired peptide-oligothiophene conjugate

The first example of an oligothiophene-peptide conjugate, which was obtained by solid-phase acylation of a resin-bound silk-inspired oligopeptide sequence with a carboxylic acid functionalized regioregular tetra(3-hexylthiophene) derivative, is reported.     

Preparation of VPS and PVD coatings for metallographic and TEM investigations

The aim of the first part of the paper is to give some advice for the faultless metallographic preparation of vacuum plasma sprayed coatings. Several coating/substrate combinations using metals, alloys and ceramics were investigated to derive some general rules. The second part deals with a preparation technique for cross-sections- of physical vapour deposition coatings. This technique was optimized for TiN and Ti(C, N) coatings on hardmetals which were examined in an analytical transmission electron microscope.     

Aurophilicity-based one-dimensional arrays of gold(I) phenylene-1,3- and -1,4-dithiolates

Phenylene-1,3-dithiol is converted into a trinuclear gold complex by treatment with 1 equiv of [[(Ph(3)P)Au](3)O](+)BF(4)(-). In the product, the phenylene unit bears one gold thiolate and one di(gold)sulfonium function. These components aggregate into one-dimensional arrays through head-to-tail aurophilic contacts between the two functions. In the association process, the Au[bond]S[bond]Au angle of the sulfonium group is opened up to accommodate the incoming gold atom between its metal centers. A similar mode of aggregation is found for the triply aurated biphenylene-4,4'-dithiol obtained using the tri(gold)oxonium salt with tri(p-tolyl)phosphine ligands. Probably for steric reasons, in this oligomerization process, the gold(I) thiolate unit is attached side-on to the digold sulfonium unit with retention of the small Au[bond]S[bond]Au angle. Under similar reaction conditions, and with the same molar ratio of the components, phenylene-1,4-dithiol is converted into the bis-sulfonium salt: 1,4-[[(p-Tol)(3)PAu](2)S](2)C(6)H(4)(BF(4))(2), the dications of which also associate into chains. Along the chains, the phenylene spacers alternate with tetranuclear gold clusters which arise from intimate aggregation of pairs of gold atoms. Together with previous findings, the present results show that gold thiolate (-SAuL) and digold sulfonium functions [-S(AuL)(2)(+)] in proper orientation at an arene unit (alpha-omega) can be considered as "soldering" points which can be used for joining up the molecular units into one-dimensional arrays solely through metal-metal contacts, which appear to be operative even against Coulomb repulsion between cations. The reaction of biphenylene-4,4'-dithiol with 2 equiv of sodium methoxide and [tri(c-hexyl)phosphine]gold chloride gives only neutral digold dithiolate complex 4 which is not associated owing to the steric bulk of the tri(c-hexyl)phosphine ligands.     

Rheology of gelling polymers in the Zimm model

In order to study rheological properties of gelling systems in dilute solution, we investigate the viscosity and the normal stresses in the Zimm model [B. H. Zimm, J. Chem. Phys. 24, 269 (1956)]. for randomly cross-linked monomers. The distribution of cluster topologies and sizes is assumed to be given either by Erdos-Renyi random graphs or three-dimensional bond percolation. Within this model the critical behavior of the viscosity and of the first normal stress coefficient is determined by the power-law scaling of their averages over clusters of a given size n with n. We investigate these scaling relations numerically and conclude that the scaling exponents are independent of the hydrodynamic interaction strength. The numerically determined exponents agree well with experimental data for branched polymers. However, we show that this traditional model of polymer physics is not able to yield a critical divergence at the gel point of the viscosity for a polydisperse dilute solution of gelation clusters. A generally accepted scaling relation for the Zimm exponent of the viscosity is thereby disproved.