双功能交联分子对生物大分子DNA磷酸骨架的修饰

利用DNA分子在水溶液中解离出的阴离子通过亲核取代反应亲核进攻重氮基乙酸叔丁酯的易离去基团重氮基来完成对DNA磷酸骨架的修饰。我们用NMR(31P)与琼脂糖凝胶电泳对结果进行表征,结果表明,DNA磷酸骨架上部分磷原子的羟基被重氮基乙酸叔丁酯修饰。     

Ti:Al2O3纳米粉体的共沉淀法合成及表征

本文采用共沉淀法合成了Ti:Al2O3纳米粉体.利用热重/差热(TG/DTA)/X射线衍射(XRD)/红外光谱(FTIR)/扫描电镜(SEM)以及能谱(EDS)等分析方法对合成的Ti:Al2O3纳米粉体进行了表征.结果分析表明:前驱体在1200℃下,保温1h可以得到纯的α-Al2O3晶相;粉体的粒径均匀、分散性好,平均粒径在25～50 nm之间.     

以纤维素/AmimCl溶液制备纤维素气凝胶

利用离子液体AmimCl溶解结合超临界CO2干燥的方法制备了纤维素气凝胶材料.研究了不同初始浓度的纤维素溶液及其在不同凝固浴中制备的纤维素凝胶的流变行为,进一步考察了纤维素溶液浓度和凝固浴种类对纤维素气凝胶材料结构的影响.结果表明,随着初始纤维素溶液浓度的增大,气凝胶的孔结构逐渐致密,比表面积随之减小;凝固浴的组成对纤维素气凝胶的结构也有较大影响.采用适当的制备条件,可以制备出高比表面积的纤维素气凝胶材料.对纤维素气凝胶的热性能进行了表征,结果表明所得到的气凝胶材料具有较好的热稳定性和较高的炭残余含量.     

高效毛细管电泳安培法测定海虾中呋喃唑酮的残留量

建立了测定虾中呋喃唑酮残留量的高效毛细管电泳-安培法.探讨了缓冲溶液浓度、酸碱度及其操作电压,进样时间,有机添加剂等条件对检测的影响.在硼砂-氢氧化钠(硼砂浓度为30mmol/L, pH:9.0)为电泳介质,甲醇为有机添加剂,在25kV分离高压的实验条件下:方法的线性范围为0.5～100mg/L,相关系数r=0.9992,检出限为0.01mg/L.     

不同形貌Co3O4的水热-微乳液法制备及其电化学性能

以四元微乳液(水/十六烷基三甲基溴化铵/环己烷/正戊醇)为介质, 在100 ℃水热环境下成功地合成了具有蒲公英状、剑麻状以及捆绑式结构的前驱化合物, 经300 ℃焙烧可得结构保持的Co3O4. X-射线衍射(XRD)、扫描电镜(SEM)测试表明, 所得样品为立方尖晶石结构, 同时水热反应时间对材料的形貌有很大的影响. 循环伏安和恒电流充放电等电化学测试均表明, 水热反应6 h、经热处理后得到Co3O4具有较好的电化学电容行为, 单电极比电容可达340 F·g-1.     

On the calculation and behavior of thermal rate coefficients for a curve crossing system

Here is used an expression, obtained from linear response theory, to carry out model calculations of thermal rate constants for a potential curve crossing system. An illustrative calculation is presented which employs a modified fast Fourier transform to study how the thermal rate coefficients are affected when non-adiabatic effects are considered. Finally an Arrhenius analysis is performed on the computed thermal rate coefficients.     

多光束激光远场干涉实验研究

设计了多组多孔径光阑,将激光扩束后通过自制的多孔径光阑,获得多光束相干激光光源.基于多光束干涉理论,通过改变不同的光阑,得到多组点状阵列分布的远场干涉图样,结果表明远场中心主瓣具有随着占空比减小能量降低、旁瓣增多的分布规律.实验结果表明,相干源呈正三角形分布时能量集中度较好.对高功率激光相干合成具有一定的参考意义.     

Pulsed Nd:YAG laser welding of AISI 304 to AISI 420 stainless steels

The technique to weld AISI 304 stainless steel to AISI 420 stainless steel with a pulsed Nd:YAG laser has been investigated. The main objective of this study was to determine the influence of the laser beam position, with respect to the joint, on weld characteristics. Specimens were welded with the laser beam incident on the joint and moved 0.1 and 0.2 mm on either side of the joint. The joints were examined in an optical microscope for cracks, pores and to determine the weld geometry. The microstructure of the weld and the heat affected zones were observed in a scanning electron microscope. An energy dispersive spectrometer, coupled to the scanning electron microscope, was used to determine variations in (weight %) the main chemical elements across the fillet weld. Vickers microhardness testing and tensile testing were carried out to determine the mechanical properties of the weld. The results of the various tests and examinations enabled definition of the best position for the incident laser beam with respect to the joint, for welding together the two stainless steels.     

对光磁共振实验中测量gF值的方法的评述和改进

对文献中测量gF因子的方法进行了评述，阐述了如何基于三角波扫场，用抽运信号确定计算和测量gF的方法。