Strain hardening of polycarbonate in the glassy state: Influence of temperature and molecular weight

This study is concerned with the temperature and molecular weight dependence of the strain-hardening behavior of polycarbonate. It is shown that the strain-hardening modulus reduces with increasing temperature and decreasing molecular weight. This result is interpreted in terms of temperature accelerated relaxation of the entanglement network. Moreover, it is shown that frozen-in orientations, induced by homogeneous deformations above the glass transition temperature, lead to anisotropic yield behavior that can be fully rationalized (and modelled) in terms of a superimposed stress contribution of the prestrained network. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 2041–2049, 2004     

Dielectric relaxation analysis of starch oligomers and polymers with respect to their chain length

Starch belongs to the polyglucan group. This type of polysaccharide shows a broad β-relaxation process in dielectric spectra at low temperatures, which has its molecular origin in orientational motions of sugar rings via glucosidic linkages. This chain dynamic was investigated for α(1,4)-linked starch oligomers with well-defined chain lengths of 2, 3, 4, 6, and 7 anhydroglucose units (AGUs) and for α(1,4)-polyglucans with average degrees of polymerization of 5, 10, 56, 70, and so forth (up to 3000; calculated from the mean molecular weight). The activation energy (E_a) of the segmental chain motion was lowest for dimeric maltose (E_a = 49.4 ± 1.3 kJ/mol), and this was followed by passage through a maximum at a degree of polymerization of 6 (E_a = 60.8 ± 1.8 kJ/mol). Subsequently, E_a leveled off at a value of about 52 ± 1.5 kJ/mol for chains containing more than 100 repeating units. The results were compared with the values of cellulose-like oligomers and polymers bearing a β(1,4)-linkage. Interestingly, the shape of the E_a dependency on the chain length of the molecules was qualitatively the same for both systems, whereas quantitatively the starch-like substances generally showed higher E_a values. Additionally, and for comparison, three cyclodextrins were measured by dielectric relaxation spectroscopy. The ringlike molecules, with 6, 7, and 8 α(1,4)-linked AGUs, showed moderately different types of dielectric spectra. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 188–197, 2004     

Amine‐cured epoxy/clay nanocomposites. II. The effect of the nanoclay aspect ratio

The thermophysical and mechanical properties of a nanocomposite material composed of amine‐cured diglycidyl ether of bisphenol A (DGEBA) reinforced with organomontmorillonite clay are reported. The storage modulus at 100 °C, which was above the glass‐transition temperature (T_g), increased approximately 350% with the addition of 10 wt % (6.0 vol %) of clay. Below the T_g, the storage modulus at 30 °C increased 50% relative to the value of unfilled epoxy. It was determined that the T_g linearly increased as a function of clay volume percent. The tensile modulus of epoxy at room temperature increased approximately 50% with the addition of 10 wt % of clay. The reinforcing effect of the organoclay nanoplatelets is discussed with respect to the Tandon–Weng and Halpin–Tsai models. A pseudoinclusion model is proposed to describe the behavior of randomly oriented, uniformly dispersed platelets in nanocomposite materials. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 4391–4400, 2004     

Homogeneous liquid-liquid extraction of uranium(VI) using tri-n-octylphosphine oxide.

A simple and efficient method for the selective separation and preconcentration of uranium(VI) using homogeneous liquid-liquid extraction was developed. Tri-n-octylphosphine oxide (TOPO) and tri-n-butylphosphate (TBP) were investigated as complexing ligands, and perfluorooctanoate ion (PFOA-) was applied as a phase separator agent under strongly acidic conditions. Under the optimal conditions ([PFOA-] = 1.7 x 10(-3) M, [TOPO] = 5.4 x 10(-4) M, [HNO3] = 0.3 M, [acetone] = 3.2% v/v) 10 microg of uranium in 40 ml aqueous phase could be extracted quantitatively into 8 microl of the sedimented phase. The maximum concentration factor was 5000-fold. However, an effort for the quantitative extraction using TBP was inefficient and the percent recovery was at most 56.7. The influence of the type and concentration of acid solution, optimum amount of the ligand, type and volume of the organic solvent, concentration of PFOA, volume of the aqueous sample and effect of different diverse ions on the extraction and determination of uranium(VI) were investigated. The proposed method was applied to the extraction and determination of uranium(VI) in natural water samples.     

Electrochemical reduction of 1-([(4-halophenyl)imino]methyl)-2-naphthols in aprotic media.

The electrochemical reduction of 1-([(4-halophenyl)imino]methyl)-2-naphthols on graphite electrodes was studied using cyclic voltammetry, chronoamperometry, constant-potential coulometry and preparative constant-potential electrolysis techniques. The data revealed that the reduction on graphite was irreversible and followed an EC mechanism. The diffusion coefficients and the number of electrons transferred were determined using the chronoamperometric Cottrell slope and the ultramicro disc Pt-electrode steady-state current. The number of electrons was also determined by bulk electrolysis. The compounds were subjected to constant-potential preparative electrolysis and the electrolysis products were purified and identified by spectroscopic methods. Based on these findings, a mechanism for the electro-reduction process is proposed.     

Selective extraction of iron(III) from aqueous nitrate solution in the presence of cobalt(II), copper(II) and nickel(II) ions using bis(delta2-2-imidazolinyl)-5,5'-dioxime.

The feasibility of using bis(delta2-2-imidazolinyl)-5,5'-dioxime (H2L) for the selective extraction of iron(III) from aqueous solutions was investigated by employing an solvent-extraction technique. The extraction of iron(III) from an aqueous nitrate solution in the presence of metal ions, such as cobalt(II), copper(II) and nickel(II), was carried out using H2L in binary and multicomponent mixtures. Iron(III) extraction has been studied as a function of the pH, equilibrium time and extractant concentration. From the extracted complex species in the organic phase, iron(III) was stripped with 2 M HNO3, and later determined using atomic-absorption spectrometry. The extraction was found to significantly depend on the aqueous solution pH. The extraction of iron(III) with H2L increases with the pH value, reaching a maximum in the zone of pH 2.0, remaining constant between 2 and 3.5 and subsequently decreasing. The quantitative extraction of iron(III) with 5 x 10(-30 M H2L in toluene is observed at pH 2.0. H2L was found to react with iron(III) to form ligand complex having a composition of 1:2 (Fe:H2L).     

Oxidation of isoniazid by quinolinium dichromate in an aqueous acid medium and kinetic determination of isoniazid in pure and pharmaceutical formulations.

The kinetics of oxidation of isoniazid in acidic medium was studied spectrophotometrically. The reaction between QDC and isoniazid in acid medium exhibits (4:1) stoichiometry (QDC:isoniazid). The reaction showed first order kinetics in quinolinium dichromate (QDC) concentration and an order of less than unity in isoniazid (INH) and acid concentrations. The oxidation reaction proceeds via a protonated QDC species, which forms a complex with isoniazid. The latter decomposes in a slow step to give a free radical derived from isoniazid and an intermediate chromium(V), which is followed, by subsequent fast steps to give the products. The reaction constants involved in the mechanism are evaluated. Isoniazid was analyzed by kinetic methods in pure and pharmaceutical formulations.     

Ultrahigh‐molecular‐weight‐polyethylene‐fiber surface treatment by electron‐beam‐irradiation‐induced graft polymerization and its effect on adhesion in a styrene–butadiene rubber matrix

Aiming to develop a high‐performance fiber‐reinforced rubber from styrene–butadiene rubber (SBR), we applied a special technique using electron‐beam (EB)‐irradiation‐induced graft polymerization to ultrahigh‐molecular‐weight‐polyethylene (UHMWPE) fibers. The molecular interaction between the grafted UHMWPE fibers and an SBR matrix was studied through the evaluation of the adhesive behavior of the fibers in the SBR matrix. Although UHMWPE was chemically inert, two monomers, styrene and N‐vinyl formamide (NVF), were examined for graft polymerization onto the UHMWPE fiber surface. Styrene was not effective, but NVF was graft‐polymerized onto the UHMWPE fibers with this special method. A methanol/water mixture and dioxane were used as solvents for NVF, and the effects of the solvents on the grafting percentage of NVF were also examined. The methanol/water mixture was more effective. A grafting percentage of 16.4% was the highest obtained. This improved the adhesive force threefold with respect to that of untreated UHMWPE fibers. These results demonstrated that EB irradiation enabled graft polymerization to occur even on the inert surface of UHMWPE fibers. However, the mechanical properties of the fibers could be compromised according to the dose of EB irradiation. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 2595–2603, 2004     

Spectrophotometric and AAS determination of trace amounts of cobalt after preconcentration by using alpha-benzilmonoxime-microcrystalline naphthalene.

The formed cobalt-a-benzilmonoxime complex was adsorbed onto microcrystalline naphthalene. Then it was determined by zero and first derivative spectrophotometry and by atomic absorption spectrophotometry (AAS) after dissolving into chloroform and methylisobutylketone (MIBK), respectively. Under optimum conditions, cobalt in the range of 1.0 - 20.0, 0.4 - 30.0 and 2.5 - 50.0 microg could be determined by spectrophotometry, first derivative spectrophotometry and AAS method, respectively. By the method, a preconcentration factor equal to approximately 30 for cobalt was obtained. The effect of diverse ions on the determination of 5.0 microg cobalt was also studied. The method was successfully applied to some pharmaceuticals and synthetic alloy samples.     

Simultaneous kinetic-spectrophotometric determination of hydrazine and acetylhydrazine in micellar media using the H-point standard addition method.

The H-point standard addition method (HPSAM), based on a spectrophotometric measurement for the simultaneous determination of hydrazine and acetylhydrazine, is described. This method is based on the difference between the rates of their reactions with N,N-dimethylaminobenzaldehyde (DAB) in the presence of sodium dodecyl sulfate (SDS) in acidic media. The results showed that hydrazine and acetylhydrazine could be determined simultaneously in the range of 0.020 - 0.70 and 0.20 - 5.0 mg L(-1), respectively. Under the working conditions, the proposed method was successfully applied to the simultaneous determination of hydrazine and acetylhydrazine in several synthetic mixtures and plasma and water samples.