Comparative Study of Biosorption of Heavy Metals Using Living Green Algae Scenedesmus quadricauda and Neochloris pseudoalveolaris: Equilibrium and Kinetics

The biosorption of several heavy metals such as cobalt(II), chromium(III), lead(II), cadmium(II), nickel(II), and manganese(II) from aqueous systems on living microalgae cultures, Scenedesmus quadricauda and Neochloris pseudoalveolaris were studied under laboratories conditions. The kinetic and statistical parameters were calculated by using the data obtained from batch cultivation and well fitted a pseudo-first-order rate equation. The initial metal concentrations in solution were about 5–40 mg · L^?1. According to the pseudo-second-order model, the biosorption capacities of Scenedesmus quadricauda for Co(II), Cr(III), Pb(II), Cd(II), Ni(II), and Mn(II) ions were found in the ranges of 2.14–52.48, 1.98–81.98, 8.05–4.26, 7.81–24.96, 2.17–55.71, and 3.54–75.20 mg g^?1, respectively. Kinetic studies revealed that the metal uptake capacity of each living green algae was rather fast. It was also observed that the biosorption kinetic rate decreased with increasing concentration for both microalgae. The application of diffusion-controlled models to the experimental results indicated that the contribution of intraparticle diffusion to the overall sorption kinetics was not very important. Results showed that Co(II), Cr(III), Pb(II), Cd(II), Ni(II), and Mn(II) ions could effectively be absorbed by using living microalga cultures from aqueous solutions.     

Cross-section calculations of proton induced (p,n) and (p,2n) reactions for production of diagnostic 67Ga, 81Rb, 111In, 123,124I, 123Cs and 123Xe radioisotopes

Investigation of pre-equilibrium (PEQ) and equilibrium (EQ) effects on proton induced reactions for production of radioisotopes are very important. Therefore, in this study, we have calculated the PEQ and EQ cross-sections for ⁶⁷Zn(p,n)⁶⁷Ga, ⁶⁸Zn(p,2n)⁶⁷Ga, ⁸²Kr(p,2n)⁸¹Rb, ¹¹¹Cd(p,n)¹¹¹In, ¹¹²Cd(p,2n)¹¹¹In, ¹²³Te(p,n)¹²³I, ¹²⁴Te(p,2n)¹²³I, ¹²⁴Te(p,n)¹²⁴I and ¹²⁴Xe(p,2n)¹²³Cs reactions for production diagnostic radioisotopes. Calculations have been performed by using the hybrid model, geometry dependent hybrid model and full exciton model of PEQ reaction mechanism with 1–40 MeV proton incident energy. We have also investigated the EQ effects on these reactions using the Weisskopf–Ewing model in the same energy range. The excitation functions including the PEQ and EQ effects on these reactions are evaluated by using the ALICE/ASH (2006) and the TALYS 1.4 (2011) codes. Our results have shown that using these codes is suitable for production diagnostic isotopes mentioned above. To obtain excitation functions for producing the diagnostic radioisotopes the PEQ mechanism has been found more dominant than that of the EQ. The results are discussed and compared with the available experimental data.     

Cone motion viscosity and optical second harmonic generation of ferroelectric liquid crystalline dendrimers

We report second harmonic generation in a ferroelectric liquid crystalline trimer and ferroelectric liquid crystalline dendrimers of first, second and third generation. Thin cells were filled with the compounds by capillary forces at elevated temperature, and cooled from the surface stabilized ferroelectric state to below the glass transition temperature, while kept in an electric field. The cone motion viscosity and the threshold electric field for unwinding of the helix axis of the chiral tilted smectic mesophases were studied separately at elevated temperature, and these data were used to optimize the preparation of the films. The measured response time was between 0.3 and 3ms, which corresponds to a cone motion viscosity between 0.5 and 50 Pa s. Second harmonic generation was studied both at elevated temperature with an electric field and at room temperature with and without electric field. The first generation dendrimer exhibited a strong increase in the second order non-linear optical response with time at room temperature. The d ₂₃-coefficient of this dendrimer was approximately four times larger than for the other macromolecules and was 0.045 pm V^-1. The relatively large d-coefficient of the first generation dendrimer is ascribed to crystallization, which improved the orientation of the molecular dipoles.     

Reversible Immobilization of Urease by Using Bacterial Cellulose Nanofibers

In this work, bacterial cellulose nanofibers were produced by using the Gluconacetobacter hansenii HE1 strain. These nanofibers were derivatized with dye affinity ligand Reactive Green 5, and these newly synthesized dye-attached nanofibers were used for affinity adsorption of urease. Reactive Green 5-attached nanofibers were characterized by Fourier transform infrared spectroscopy, SEM, and energy-dispersive x-ray spectroscopy analysis. Some adsorption conditions which significantly affect the adsorption efficiency were investigated. The maximum urease adsorption capacity was found to be 240 mg/g nanofiber in pH 6.0 and at room temperature. Dye-free plain nanofibers also used for studying nonspecific urease adsorption onto plain nanofibers and nonspecific adsorption were found to be negligible (3.5 mg/g nanofiber). Prepared dye-attached nanofibers can be used in five successive adsorption/desorption steps without any decrease in their urease adsorption capacity. The desorption rate of the adsorbed urease was found to be 98.9 %. The activity of the urease was also investigated, and it was found that free and desorbed urease from the dye-attached nanofibers showed similar specific activity.     

Analytical application of the poly(1H-1,2,4-triazole-3-thiol) modified gold electrode for high-sensitive voltammetric determination of catechol in tap and lake water samples

ABSTRACT

In this work, a simple, sensitive and rapid method for the determination of trace amounts of catechol (CT) in aqueous media has been suggested. For this purpose, poly(1H-1,2,4-triazole-3-thiol) film was electrochemically deposited successfully at the gold electrode (Au/T3T). The electrochemical behaviour of CT was studied on the Au/T3T electrode by the cyclic voltammetry and differential pulse voltammetry techniques. The anodic peak current value and the concentration of CT showed a good linear relationship in the range of 0.015–2.8 µM. The limit of detection was found as 1.88 nM (S/N = 3). Besides, the reproducibility, repeatability, stability and interference measurements were also assayed. This sensor was applied successfully for the detection of CT in synthetic and real samples.     

Cloud point extraction of aluminum (III) in water samples and determination by electrothermal atomic absorption spectrometry,flame atomic absorption spectrometry and UV-visible spectrophotometry

Cloud point extraction was applied as a preconcentration step for the determination of trace level of Al(III) in water samples with electrothermal atomic absorption spectrometry (ETAAS), flame atomic absorption spectrometry (FAAS) and UV-visible spectrophotometry. The aluminum was extracted as aluminum-Eriochrome Cyanine R (ECR) complex, at pH 6 by micelles of the non-ionic surfactant octylphenoxypolyethoxyethanol (Triton X-114). The investigations showed that the same CPE procedure can be used for different detection techniques. The results obtained from these techniques were evaluated. Under the optimal conditions, limit of detection obtained with ETAAS, FAAS and UV-visible spectrophotometry were 0.03 ng mL^?1, 0.06 µg mL^?1 and 0.01 µg mL^?1, respectively. The accuracy of the procedure was tested by analysing certified reference material. The method was successfully applied to determination of aluminum in water samples and dialysis fluid.     

Selective back-extraction and preconcentration of zinc(II) from metal-1,3,5-triketone extracts prior to its determination by flame atomic absorption spectrometry

A simple back-extraction method was developed for the separation and preconcentration of trace levels of zinc from different matrices. Ethyl-2-(4-methoxybenzoyl)-3-(4-methoxyphenyl)-3-oxopropanoylcarbamate (EMPC) was used as a new complexing agent for the extraction of zinc(II) from the aqueous sample phase to the methyl isobutyl ketone (MIBK) phase as Zn(EMPC)₂ complexes. The Zn(II) can be selectively stripped with 1?mL of 0.5?mol?L^?1 HCl from Mⁿ⁺(EMPC)_n complexes [Ag(I), Al(III), Cd(II), Cr(III), Cu(II), Fe(II), Fe(III), Mn(II), Ni(II), Pb(II) and Pd(II)] which dissolved in MIBK phase. Some experimental parameters, which are important for the whole extraction process, including pH, sample volume, shaking time, amount of the EMPC reagent, amount of MIBK, ionic strength, and type of back-extractant were investigated. The recovery for Zn(II) was greater than 95%. The detection limit of the method was found to be 0.2?µg?L ^{? 1} and the relative standard deviation as 6.4%. The concentrations of Zn(II) in the certified reference materials (LGC6019 river water and NIST-1547 peach leaves) by the presented method were in good agreement with the certified values. The proposed method was succesfully applied to the determination of zinc in some natural waters, rice, hair, soil, and tea samples.     

Synthesis in water-free DMF, characterization, electrical, and gas sensing properties of bis[2-(2-aminoethylamino)ethanol]copper(II) dibromide

2-(2-Aminoethylamino)ethanol (L) reacts with cupric bromide in dimethylformamide to give a mononuclear complex of Cu(II) [L₂Cu]Br₂, with six-coordinate distorted octahedral geometry, in which two molecules of tridentate (N,N,O) ligand are involved. The structure was confirmed by spectroscopic methods, elemental and thermogravimetric analyses, and magnetic measurements. Optimization of possible configurations indicated the formation of the trans structure of the complex. Experimental results indicate that the investigated complex, bis[2-(2-aminoethylamino)ethanol] copper(II) bromide, behaves as a semiconductor in the studied temperature range of 298–388 K. Gas sensing properties of the film for the volatile organic compounds (VOCs): acetone, tetra-chloromethane, chloroform, ethanol, and methanol, were also investigated as a function of vapor concentration and temperature in dark. The film showed maximum sensitivity to tetrachloromethane and ethanol vapors at room temperature. Responses of the film to the tested gases are reversible.     

Preparation of Methyl 6‐O‐p‐Nitrobenzoyl‐β‐d‐Glucoside

Methyl 6‐O‐p‐nitrobenzoyl‐β‐d‐glucoside was synthesized by reacting methyl 4,6‐O‐p‐nitrobenzylidine‐β‐d‐glucoside with N‐bromosuccinimide (NBS). First, methyl β‐d‐glucoside was converted into methyl 4,6‐O‐p‐nitrobenzylidine‐β‐d‐glucoside with p‐nitrobenzaldehyde. Later, methyl 4,6‐O‐p‐nitrobenzylidine‐β‐d‐glucoside was opened oxidatively with NBS to give methyl 6‐O‐p‐nitrobenzoyl‐β‐d‐glucoside.     

Synthesis and characterization of tellurium-doped CdO nanoparticles thin films by sol–gel method

In this work, tellurium (Te) doped CdO nanoparticles thin films with different Te concentrations (1, 3, 5, 7 and 10 %) were prepared by sol–gel method. The effects of Te doping on the structural, morphological and optical properties of the CdO thin films were systematically studied. From X-ray diffraction spectra, it has seen that all of thin films were formed polycrystalline and cubic structure having (111), (200) and (311) orientations. The structure of CdO thin films with Te-dopant was formed the unstable CdTeO₃ monoclinic structure crystal plane ( $ {\bar{\text{1}}\text{22}} $ 1 ¯ 22 ), however, the intensity of this unstable peak of the crystalline phase decreased with the increase of Te-doping ratio. The strain in the structure is also studied by using Williamson-Hall method. From FE-SEM images, it has seen that particles have homogeneously distributed and well hold onto the substrate surface. Additionally, grain size increases from 27 to 121 nm with the increase of Te-doping ratio. Optical results indicate that 1 % Te-doped CdO thin film has the maximum transmittance of about 87 %, and the values of optical energy band gap increases from 2.50 to 2.64 eV with the increase of Te-doping ratio. These results make Te-doped CdO thin films an attractive candidate for thin film material applications.