Synthesis and characterization of poly(arylene ether)s containing 6‐(4‐hydroxyphenyl)pyridazin‐3(2H)‐one or 6‐(4‐hydroxyphenyl)pyridazine moieties

A series of novel soluble pyridazinone‐ or pyridazine‐containing poly(arylene ether)s were prepared by a polycondensation reaction. The pyridazinone monomer, 6‐(4‐hydroxyphenyl)pyridazin‐3(2H)‐one ( 1 ), was synthesized from the corresponding acetophenone and glyoxylic acid in a simple one‐pot reaction. The pyridazinone monomer was successfully copolymerized with bisphenol A (BPA) or 1,2‐dihydro‐4‐(4‐hydroxyphenyl)phthalazin‐1(2H)‐one (DHPZ) and bis(4‐fluorophenyl)sulfone to form high‐molecular‐weight polymers. The copolymers had inherent viscosities of 0.5–0.9 dL/g. The glass‐transition temperatures (T_g's) of the copolymers synthesized with BPA increased with increasing content of the pyridazinone monomer. The T_g's of the copolymers synthesized from DHPZ with different pyridazinone contents were similar to those of the two homopolymers. The homopolymers showed T_g's from 202 to 291 °C by differential scanning calorimetry. The 5% weight loss temperatures in nitrogen measured by thermogravimetric analysis were in the range of 411–500 °C. 4‐(6‐Chloropyridazin‐3‐yl)phenol ( 2 ) was synthesized from 1 via a simple one‐pot reaction. 2 was copolymerized with 4,4′‐isopropylidenediphenol and bis(4‐fluorophenyl)sulfone to form high‐T_g polymers. The copolymers with less than 80 mol % pyridazinone or chloropyridazine monomers were soluble in chlorinated solvents such as chloroform. The copolymers with higher pyridazinone contents and homopolymers were not soluble in chlorinated solvents but were still soluble in dipolar aprotic solvents such as N‐methylpyrrolidinone. The soluble polymers could be cast into flexible films from solution. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 3328–3335, 2006     

Postmodification of poly(9‐alkyl‐9H‐carbazole‐2,7‐diyl)s as a route to new main‐chain‐functionalized carbazole polymers

The postmodification of poly[9‐(2‐hexyldecyl)‐9H‐carbazole‐2,7‐diyl] ( P1 ) upon its reaction with N‐bromosuccinimide affords exclusive and full bromination of the 3,6‐positions of the carbazole repeat units to yield poly[3,6‐dibromo‐9‐(2‐hexyldecyl)‐9H‐carbazole‐2,7‐diyl] ( P2 ). Brominated polymer P2 can be used as a precursor for further functionalization at the 3,6‐positions with the desired functional group to afford other useful polymers. Polymer P2 has hence been reacted with copper(I) cyanide to afford poly[3,6‐dicyano‐9‐(2‐hexyldecyl)‐9H‐carbazole‐2,7‐diyl] ( P3 ). Full substitution of the bromide groups with nitrile‐functional groups has been achieved. The preparation and structural characterization of polymers P2 and P3 are presented together with studies on their electronic conjugation and photoluminescence properties. Cyclic voltammetry studies on polymer P3 indicate that the new polymer is easier to reduce (n‐dope) but more difficult to oxidize than its unsubstituted counterpart ( P1 ) as a result of the introduction of the electron‐withdrawing nitrile‐functional groups at the 3,6‐positions on the carbazole repeat units on the polymer chains. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 3336–3342, 2006     

Novel blue‐greenish electroluminescent poly(fluorenevinylene‐alt‐dibenzothiophenevinylene)s and their model compounds

Poly(9,9‐dihexylfluorene‐2,7‐vinylene‐alt‐dibenzothiophene‐2,8‐vinylene) (PS) and poly(9,9‐dihexylfluorene‐2,7‐vinylene‐alt‐dibenzothiophene‐5,5‐dioxide‐2,8‐ vinylene) (PSO) as well as corresponding model compounds were synthesized by Heck coupling. Both the polymers and model compounds were readily soluble in common organic solvents such as tetrahydrofuran, dichloromethane, chloroform, and toluene. The polymers showed a decomposition temperature at ～430 °C and a char yield of about 65% at 800 °C in N₂. The glass‐transition temperatures of the polymers were almost identical (75–77 °C) and higher than those of the model compounds (26–45 °C). All samples absorbed around 390 nm, and their optical band gaps were 2.69–2.85 eV. They behaved as blue‐greenish light emitting materials in both solutions and thin films, with photoluminescence emission maxima at 450–483 nm and photoluminescence quantum yields of 0.52–0.72 in solution. Organic light‐emitting diodes with an indium tin oxide/poly(ethylene dioxythiophene):poly(styrene sulfonic acid)/polymer/Mg:Ag/Ag configuration with polymers PS and PSO as emitting layers showed green electroluminescence with maxima at 530 and 540 nm, respectively. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 6790–6800, 2006     

Cyclolinear polysiloxanes. II. Crosslinking and characterization

The synthesis and characterization of two groups of novel networks prepared from cyclolinear polysiloxanes are described. The first group of networks from cyclolinear polysiloxanes (N‐CLPSs) was synthesized by the hydrosilation of vinyl‐terminated cyclolinear polyorganosiloxanes [prepared from diacetoxydiethyltetramethylcyclotetrasiloxane (D₄Et₂OAc₂) or diacetoxytriethylpentamethylcyclopentasiloxane (D₅Et₃OAc₂)] with a copolymer of dimethylsiloxane and methylhydrosiloxane as the crosslinking agent. Hydrosilation was effected with a platinum carbonyl catalyst with a cyclovinylsiloxane moderator. The second group of networks (N‐eCLPSs) was prepared similarly with extended cyclolinear polysiloxanes. The mechanical properties of the novel networks were comparable to those of polydimethylsiloxane networks (N‐PDMS). The oxygen permeabilities were similar to or slightly higher than that of N‐PDMS. The glass‐transition temperatures of D₄Et₂OAc₂‐ and D₅Et₃OAc₂‐based N‐CLPSs were ?67.8 and ?90.8 °C, respectively, whereas the incorporation of polydimethylsiloxane spacers into similar N‐eCLPSs lowered their glass‐transition temperatures to ?109.7 and ?115.0 °C. Upon heating to 800 °C in air, N‐CLPSs yielded more residue than N‐eCLPSs, which in turn yielded more residue than N‐PDMS. These results may have been due to the presence of T units in the cyclic siloxane units, which may have inhibited chain degradation or the formation of volatile products. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 4053–4062, 2006     

Polymer electrolyte membranes for the direct methanol fuel cell: A review

The direct methanol fuel cell (DMFC) has the potential to replace lithium‐ion rechargeable batteries in portable electronic devices, but currently experiences significant power density and efficiency losses due to high methanol crossover through polymer electrolyte membranes (PEMs). Numerous publications document the synthesis and characterization of new PEMs for the DMFC. This article reviews this research, transport phenomena in PEMs, and experimental techniques used to evaluate new PEMs for the DMFC. Although many PEMs do not show significant improvements over Nafion®, the benchmark PEM in DMFCs, experimental results show that several new PEMs exhibit lower methanol crossover at similar proton conductivities and/or higher DMFC power densities. These results and recommendations for future research are discussed. © 2006 Wiley Periodicals, Inc. J Polym Sci Parts B: Polym Phys 44: 2201–2225, 2006     

Probing the use of small‐angle light scattering for characterizing structure of titanium dioxide/low‐density polyethylene nanocomposites

Small‐angle light scattering (SALS) measurements were used to study the structure of titanium dioxide (TiO₂)/low‐density polyethylene (LDPE) nanocomposites. The results showed that the scattering from LDPE crystalline structures and the scattering from TiO₂ nanoparticles can be resolved and separated. It is shown that the independent effects of crystallization conditions and the presence of nanoparticle aggregates on the spherulitic structure of the LDPE matrix can be determined by analyzing the scattering patterns using the methods proposed. From the SALS results, we conclude that the nanoparticle surface chemistry affects both nucleation of spherulites and their structure particularly under rapid cooling conditions. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 1084–1095, 2006     

Acrylic acid level and adhesive performance and peel master‐curves of acrylic pressure‐sensitive adhesives

Three series of pressure‐sensitive adhesives were prepared with constant glass‐transition temperature, using emulsion polymerization. The monomers chosen were butyl acrylate, 2‐ethylhexyl acrylate (EHA), methyl methacrylate (MMA), and acrylic acid (AA). Within each polymer series, the proportion of AA monomer was held constant for each polymer preparation but acrylic ester monomer levels were varied. Adhesion performance was assessed by measurement of loop tack, static shear resistance, and through the construction of peel master‐curves. Peel master‐curves were generated through peel tests conducted over a range of temperatures and peel rates and through application of the time–temperature superposition principle. Bulk effects dominated by polymer zero shear viscosity change as AA and EHA levels were varied were attributed to the observed effect on static shear resistance and the horizontal displacements of peel master‐curves. Static shear resistance was found to strongly correlate with log(a_C), a parameter introduced to horizontally shift peel master‐curves to form a superposed, “super master‐curve”. An interfacial interaction was proposed to account for deviations observed when loop tack was correlated with log(a_C). Surface rearrangements via hydrogen bonding with the test substrate were suggested as responsible for the interfacial interaction. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 1237–1252, 2006     

Rheology,morphology, and estimation of the interfacial tension of binary blends based on low‐density polyethylene/poly(trimethylene terephthalate) and high‐density polyethylene/poly(trimethylene terephthalate) [retracted article]

It has come to our attention that this article, “Rheology, Morphology, and Estimation of the Interfacial Tension of Binary Blends Based on Low‐Density Polyethylene/Poly(trimethylene terephthalate) and High‐Density Polyethylene/Poly(trimethylene terephthalate)” by A. A. Shokri and S. E. Zamani was previously published under the title, “Rheology, Morphology and Estimation of Interfacial Tension of LDPE/EVA and HDPE/EVA Blends” by H. A. Khonakdar, S. H. Jafari, A. Yavari, A. Asadinezhad, U. Wagenknecht, in Polymer Bulletin 54, 75–84 (2005), . We have retracted the article, and offer our apologies to the authors of the original paper.     

Indirect fluorometric determination of diclofenac sodium.

A simple and easy method of analysis for diclofenac sodium is reported. A spectrofluorometric method for the microdetermination of diclofenac sodium has been developed through its reaction with cerium(IV) in an acidic solution and measurement of the fluorescence of the Ce(III) ions produced. Under the optimum experimental conditions for the oxidation reaction, 1.0 M H2SO4 with 90 min of heating time (100 degrees C), the range of application is 124.3-600 ng mL(-1) and the limit of detection is 72.7 ng mL(-1). The proposed method was applied to the determination of diclofenac sodium in pharmaceutical tablets. The results of the analysis show a good agreement with those obtained by the official USP 27 HPLC method.     

Gold ultra-microelectrode arrays: application to the steady-state voltammetry of hydroxide ion in aqueous solution.

Gold ultra-microelectrode arrays are used to explore the electrochemical oxidation of hydroxide ions and are shown to be analytical useful. Two types of ultra-microelectrode arrays are used; the first consist of 256 individual electrodes of 5 microm in radius, 170 of which are electrochemically active in a cubic arrangement which are separated from their nearest neighbour by a distance of 100 microm. The second array compromises 2597 electrodes of 2.5 microm in radius and of which 1550 of which are electrochemically active in a hexagonal arrangement separated by the nearest neighbour by 55 microm. Well defined voltammetric waves are found with peak currents proportional to the concentration of hydroxide ions in the range 50 microM to 1 mM. Detection limits of 20 microM using the 170 ultra-microelectrode and 10 microM with the 1550 ultra-microelectrode array are shown to be possible but with a higher sensitivity of 4 mA M(-1) observed using the 1550 ultra-microelectrode array compared to 1.2 mA M(-1) with the 170 ultra-microelectrode array.