Maximization of the lift/drag ratio of airfoils with a turbulent boundary layer

The problem of seeking the maximum life/drag ratio for airfoils in an incompressible separationless high-Re flow is considered in the turbulent boundary layer approximation. Within the framework of this model, the maximization of the L/D ratio is redwed to the determination of a conditional extremum for a convex functional. An explicit analytical expression for the extremal solution is obtained. The angle-of-attack dependence of the L/D ratio is demonstrated. The global maximum of the L/D ratio is determined. The results are compared with the known data of numerical optimization. Kazan’. Translated from Izvestiya Rossiiskoi Akademii Nauk, Mekhanika Zhidkosti i Gaza, No. 3, pp. 177–184, May–June, 1998.     

Numerical study of boundary layer transition in flowing film evaporation on horizontal elliptical cylinder

A numerical study of the onset of longitudinal transition between turbulent and laminar regimes during the evaporation of a water film is presented. These water film streams along a horizontal elliptical tube under the simultaneous effects of gravity, pressure gradients, caused by the vapor flow and curvature, and viscous forces. At the interface of water vapor, the shear stress is supposed to be negligible. Outside the boundary layer, the vapor phase velocity is obtained from potential flow. In the analysis Von Karmans turbulence model is used and the inertia and convection terms are retained. Transfers equations are discretised by using the implicit Keller method. The effects of an initial liquid flow rate per unit of length, Froude number, temperature difference between the wall and the liquid–vapor interface and ellipticity on the transition position have been evaluated. The transition criterion has been given in term of the critical film Reynolds number (Re)_C.     

Direct Statistical Simulation of a Supersonic Flow of a Binary Mixture of Rarefied Gases around a Transversely Positioned Cylinder

A supersonic flow of a binary mixture of gases in a wide range of rarefaction (from a flow with a Knudsen number K _n = 0.1 to a free-molecular flow) around a cylinder is studied by means of direct statistical Monte Carlo simulations (DSMC method). The influence of a small fraction of heavy particles in a light gas flow on the region of significant nonequilibrium near the cylinder and on the heat flux is considered.__________Translated from Prikladnaya Mekhanika i Tekhnicheskaya Fizika, Vol. 46, No. 5, pp. 53–59, September–October, 2005.     

Extended glare point velocimetry and sizing for bubbly flows

A novel measuring technique for bubbly flows, named glare point velocimetry and sizing (GPVS), was developed in order to measure both bubble size and velocity with high accuracy in a 2D plane. This is accomplished by observing glare points in-focus under an observation angle of 96°. When a second laser-sheet is added, even higher accuracies are obtained and the relative refractive index of the bubble can be measured. It also allows non-spherical bubbles to be rejected and arbitrary angles to be used (e.g. 90°). The accuracy of the size and refractive index measurements was found to be within 1.3%.     

Random Lattices with Fractal Bond Permeabilities

The macroscopic permeability of random lattices has been studied when the permeability of each link is a power law of its length with an exponent . When they are sufficiently long, the link lengths are shown to follow exponential laws which depend on the density. The macroscopic permeability is studied as a function of ; it is compared to a modified effective medium theory (EMT).*Author for correspondence: e-mail: adler@ipgp.jussieu.fr**e-mail: le_chic@mail.ru     

Dynamics of hybrid shafts

In this paper the dynamic performance and cross-section deformation of shafts made of metals (steel and aluminum), composites (CFRP and GFRP) and hybrids of metals and composites have been studied. A layered finite degenerated shell element with transverse shear deformation and dynamic behavior is employed. Results obtained show that improvements in dynamic performance and reduction of cross-section deformation of hybrid shafts over metallic and composite shafts are possible.     

Turbulent flow past a transverse cavity with inclined side walls. 1. Flow structure

The process of vortex formation in a cavity with inclined walls, which has a moderate aspect ratio, is experimentally studied, and the distribution of pressure coefficients is measured. The angle of inclination of the side walls ϕ is varied from 30 to 90°. It is found that the flow in the cavity becomes unstable in the range of inclination angles ϕ = 60–70°. Flow reconstruction occurs, which substantially alters the surface-temperature and static-pressure distributions. Large changes in these characteristics and their nonuniform distributions for these angles are observed across the cavity on its frontal wall and on the bottom. For small angles (ϕ = 30 and 45°), the pressure on the rear wall drastically increases, which leads to a small increase in pressure averaged over the entire cavity surface. __________ Translated from PrikladnayaMekhanika i Tekhnicheskaya Fizika, Vol. 47, No. 5, pp. 68–76, September–October, 2006.     

Plasma in a high-frequency electric field with a reflective condition on the boundary

An analytical solution is obtained for the linearized problem of the behavior of a collisional gas plasma in a half-space in an external alternating electric field. It is assumed that the electrons are mirror-reflected from the plasma boundary. The solution is used for finding the screened field. The case of an external field frequency close to the plasma frequency is investigated separately.     

Determination of the complex shear modulus of structural adhesives using a doubly clamped sandwich beam

A method is described for calculating the complex shear modulus of structural adhesives from dynamic test data on a doubly clamped sandwich beam in which the adhesive is contained as a thin layer. The accuracy of the technique is validated by finite-element analysis. Values of modulus obtained using the doubly clamped beam technique are found to be in excellent agreement with values obtained from dynamic tests on bulk specimens of an epoxy adhesive.     

Boundary element simulations of spheres settling in circular,square and triangular conduits

Numerical simulations of a spherical particle sedimenting in circular, triangular and square conduits containing a viscous, inertialess, Newtonian fluid were investigated using the Boundary Element Method (BEM). Settling velocities and pressure drops for spheres falling along the centre-lines of the conduits were computed for a definitive range of sphere sizes. The numerical simulations for the settling velocities showed good agreement with existing experimental data. The most accurate analytic solution for a sphere settling along the axis of a circular conduit produced results which were almost indistinguishable from the present BEM calculations. For a sphere falling along the centre-line of a square conduit, the BEM calculations for small spheres agreed well with analytic results. No analytic results for a sphere falling along the axis of a triangular conduit were available for comparison. Extrapolation of the BEM predictions for the pressure drops, to infinitely small spheres, showed remarkable agreement with analytic results. For the circular conduit, the sphere's settling velocity and angular velocity were computed as a function of drop position for small, medium and large spheres. Excellent agreement with a reflection solution was achieved for the small sphere. In addition, end effects were investigated for centre-line drops and compared where possible with available experimental data and analytic results.Los Alamos National Laboratory, Los Alamos, New Mexico, USA.