大跨度叠合梁斜拉桥多维多点非平稳随机地震响应分析

为研究地震动非平稳特性对大跨度叠合梁斜拉桥随机地震响应的影响,采用绝对位移求解的虚拟激励法在通用有限元软件中对某座叠合梁斜拉桥进行多维多点非平稳随机地震响应分析.研究结果表明:采用绝对位移求解的虚拟激励法,能在通用有限元软件中高效地实现对大跨度叠合梁斜拉桥多维多点非平稳随机地震响应分析;设计中假定地震动平稳性,得到的结果偏于保守;行波效应对大跨度叠合梁斜拉桥结构响应有显著影响,考虑行波效应对主塔塔顶位移和塔底内力是有利的,但应注意其对主梁跨中位移和内力的不利影响.     

宽谱高分辨平场凹面全息光栅光谱仪设计

为了获得宽谱、高分辨的平场凹面全息光栅,将全息凹面光栅理论、遗传算法、衍射级次空间共用和同时消像差思想融合在一起,提出设计宽谱、高分辨平场凹面全息光栅的方法,给出了实际设计步骤。通过Zemax软件光线追迹仿真具体实例,给出了200～800nm波段的点列图变化曲线[均方根(RMS)约为11μm],以10μm×1mm狭缝入射,其光照度光谱图显示光谱分辨率在200～400nm波段为0.25nm,在400～800nm波段为0.5nm。该方法可以用于设计小型化、实用化的宽谱和高分辨平场凹面全息光栅光谱仪光学系统。     

咪唑类二阶非线性光学活性分子的设计、合成及性能

设计、合成了两个新的咪唑类二阶非线性光学生色团，对其热性能、透明性和 二阶非线性光学性能进行了测定和研究，实验表明生色团为非线性光学性能-透明 性-热稳定性能综合优化的有机二阶非线性光学生色团。     

兼具非线性光学和热释电性能的有机-无机杂化薄膜

用溶胶-凝胶法和原位加热极化聚合法制备了以4-[N,N-二-(二羟乙基)氨基苯基]-2,4-二-(4,4-二硝基苯基)咪唑(4HAPN)为生色团,以Ta(Ⅴ)的金属醇盐为无机前驱体的有机-无机杂化聚合物材料.用二次谐波产生技术和数字电荷积分法测得极化薄膜的二阶非线性光学系数d₃₃为17.2pm/V,平均热释电系数为4.3×10^-6C/(cm²·K).     

新型含氟聚苯撑乙烯的合成及电致发光性能

设计并合成了两个不同烷氧基增溶的结构新颖的含氟聚苯撑乙烯Pa, Pb和共聚物Pc. 通过核磁共振和元素分析对其结构进行了表征, 通过热重分析、凝胶色谱测定了其热分解温度和分子量及分布; 紫外-可见吸收光谱仪和荧光分光光度计测得其吸收-发射光谱. 测量发现热失重曲线拐点温度超过400 ℃. 由2-乙基己基增溶的Pa和Pc具有优异的溶解性, 固态荧光发射波长分别为499和585 nm, 相应比PPV和MEH-PPV稍有蓝移. 应用旋转涂膜的方法制作Pa和Pc的双层器件(ITO/PEDOT/Polymer/Ba/Al), 电致发光波长分别为494和604 nm, 器件均具有较低的启动电压(4 V左右), 分别在24和15 V时达到最大亮度598和203 cd•m^－2, 而此时电流密度分别为100和80 mA•cm^－2.     

激光诱导击穿光谱对不规则未知镀层样品的分析

传统经典的镀层分析方法分析速度慢,对于不规则镀层样品较难分析,文中在最佳分析条件下,采用激光诱导击穿光谱法对两块不规则未知镀层样品进行分析,镀层分析曲线表明,两块未知镀层样品采用渗锌工艺制备而成,镀层表面的锌、 铁元素是主量元素,少量的铬起钝化作用,镀层界面下则是中低合金钢,用一套中低合金钢标准样品建立校准曲线,准确分析了镀层界面下中低合金钢的化学成分及Cr和Mo元素在镀层表面的含量变化情况,从而对未知不规则镀层样品的化学成分有一个深入的了解。     

2-(4-N-硝基，N-甲基氨基苯基)-(4-硝基苯基)-5-(2,4,6- 三硝基苯基)噻唑的 合成及其性能研究

为解决非线性光学活性有机分子透明性差及熔点低的问题,设计合成了2-(4-N-硝基,N-甲基氨基苯基)-(4-硝基苯基)-5-(2,4,6-三硝基苯基)噻唑化合物,并研究了其热性能及光学性质。根据实验结果得出由于杂环的引入,提高了化合物的裂解温度,并较好地改善了有机分子的透明性。     

A fast improved fat tree encoder for wave union TDC in an FPGA

Up to now, the wave union method can achieve the best timing performance in FPGA-based TDC designs. However, it should be guaranteed in such a structure that the non-thermometer code to binary code (NTH2B) encoding process should be finished within just one system clock cycle. So the implementation of the NTH2B encoder is quite challenging considering the high speed requirement. Besides, the high resolution wave union TDC also demands that the encoder convert an ultra-wide input code to a binary code. We present a fast improved fat tree encoder (IFTE) to fulfill such requirements, in which bubble error suppression is also integrated. With this encoder scheme, a wave union TDC with 7.7 ps RMS and 3.8 ps effective bin size was implemented in an FPGA from Xilinx Virtex 5 family. An encoding time of 8.33 ns was achieved for a 276-bit non-thermometer code to a 9-bit binary code conversion. We conducted a series of tests on the oscillating period of the wave union launcher, as well as the overall performance of the TDC; test results indicate that the IFTE works well. In fact, in the implementation of this encoder, no manual routing or special constraints were required; therefore, this IFTE structure could also be further applied in other delay-chain-based FPGA TDCs.     

A new method of waveform digitization based on time-interleaved A/D conversion

Time interleaved analog-to-digital conversion (TIADC) based on parallelism is an effective way to meet the requirement of the ultra-fast waveform digitizer beyond Gsps. Different methods to correct the mismatch errors among different analog-to-digital conversion channels have been developed previously. To overcome the speed limitation in hardware design and to implement the mismatch correction algorithm in real time,this paper proposes a fully parallel correction algorithm. A 12-bit 1-Gsps waveform digitizer with ENOB around 10.5 bit from 5 MHz to 200 MHz is implemented based on the real-time correction algorithm.     

Proposal of the readout electronics for the WCDA in the LHAASO experiment

The LHAASO(Large High Altitude Air Shower Observatory)experiment is proposed for a very high energy gamma ray source survey,in which the WCDA(Water Cherenkov Detector Array)is one of the major components.In the WCDA,a total of 3600 PMTs are placed under water in four ponds,each with a size of150 m×l50 m.Precise time and charge measurement is required for the PMT signals,over a large signal amplitude range from a single P.E.(photo electron)to 4000 P.E.To fulfill the high requirement of a signal measurement in so many front end nodes scattered in a large area,special techniques are developed,such as multiple gain readout,hybrid transmission of clocks,commands and data,precise clock phase alignment and new trigger electronics.We present the readout electronics architecture for the WCDA and several prototype modules,which are now being tested in the laboratory.