Detection of Tumor Necrosis Factor Gene by Piezoelectric Nucleic Acid Senosr

A piezoelectric nucleic acid sensor was constructed ofr detection of tumor necrosis factor gene.Two methods were employed for immobilization of nucleic acid probe on gold electrode of piezoelectric crystal.The results show that polyethyleneimine adbesion and glutaraldehyde cross-linking method has higher sensitivity,stability and selectivity than protein A method.The solid-phase nucleic acid hybridization of oligo unclecotides and tumor necrosis factor target gene sequence were monitorde using this sensor.Tumor necrosis factor gene sequence(580bp) was detected by this nucleic acid sensor for the first time.     

液晶环氧树脂研究进展

综述了液晶环氧树脂研究的新进展，介绍了液晶环氧化合物以及固化剂的种类和主要性质，着重介绍了环氧化合物活性，分子量以及与固化剂的匹配对液晶环氧树脂性质的影响。还简述了液晶环氧树脂的性能以及应用前景。     

亲电性对醌二甲烷与富电子烯烃的电荷转移聚合

概述了亲电性对醌二甲烷与富电子烯烃电荷转移聚合的最新进展，着重介绍聚合的一般特征、引发机理、链增长机理，以及单体结构、溶剂对聚合反应的影响。     

碳纤维微电极研究(Ⅺ)——利用温度效应测定电极反应的热力学和动力学参数

研究了温度对碳纤维微电极上伏安曲线的影响及温度与电极电位的关系,测定了电极反应的热力学参数.由电流与温度的关系测定了去极剂的扩散活化能E_(al)和D_o,利用微电极具有高速传质的特性,测定了常规电极上为可逆反应的电极反应标准速率常数(?),并通过(?)与温度的关系测定了电极反应的活化能.     

Electrochemical Characteristics of Mg0.9Ti0.1-xZrxNi （x=0.02, 0.04, 0.06） Alloys

Mg-based hydrogen storage alloys Mg0.9Ti0.1-xZrxNi (x=0.02, 0.04, 0.06) were successfully prepared by means of mechanical alloying (MA). The effects of Zr addition on the discharge capacity and the cycle performance of the Mg-based electrodes were also studied. It was found that the discharge capacities were improved with addition of a small amount of Zr and the cycle performances of the alloy were stabilized with the addition of Ti. The effects of surface modification or coating on the properties of Mg0.9Ti0.06Zr0.04Ni were also studied. The results indicated that coating with graphite improved both the discharge capacity and cycle life of the amorphous Mg0.9Ti0.06Zr0.04Ni electrode.     

Catalytic Enantioselective Reduction of Prochiral Ketones with Chiral Ferrocenyl Amino Alcohols

The asymmetric reduction of prochiral ketones was catalyzed by a class of recoverable and highly stable chiral ferrocenyl amino alcohols derived from natural amino acids to yield optically active secondary alcohols in high chemical yields and moderate to good enantiomeric excesses.     

Solution Structure and Behavior of Benzophenone-based Achiral Bisphosphine Ligands in Noyori-Type Ru（Ⅱ）-Catalysts

We herein report on solution structural studies of Ru^Ⅱ catalysts （3a, 9） composed of achiral bisphosphine ligands （4, 8） and the enantiopure 1,2-diphenylethylenediamine （DPEN）. Complete chiral induction from enantiopure （R,R）-DPEN to achiral bisphosphine ligand 3a was observed in solution, with the complex adopting a single, stable and non-fluxional （even at 70 ℃） configuration. The coordination of the C=O moiety in 4 to the cationic Run center is considered to be of key importance in providing the higher thermodynamic and kinetic rotation barrier for the flexible bisphosphine ligand in the complex. The obtained enantioselectivity （91% enantiomeric excess） and sense of chiral induction in the hydrogenation of acetophenone were found to be solely dependent on the chirality of the 1,2-diamine. Consistent with the hydrogenation product, the （R,R）-DPEN induces a M-conformation （fight-handed） chirality for flexible phosphine ligand 4 in the complex, resulting in a 2,2-configuration about the Ru^Ⅱ center.     

三段加热系统对大尺寸MPOF预制棒一步拉伸工艺

采用自行设计的微结构聚合物光纤专用拉丝系统对大尺寸微结构聚合物光纤预制棒的一步拉伸工艺进行了研究.该微结构聚合物光纤加热系统采用三段式梯度加热,可保持炉内温度的控制准确度在±2℃以内.在保持送料速度与牵引速度恒定、协调的条件下,通过对温度场温度梯度控制优化,确定了最佳拉丝温度组合,并得到了直径规格310 μm、标准偏差为±20 μm的较高质量的微结构聚合物光纤.     

江苏盱眙出土夹纻胎漆器的测试分析

采用激光拉曼光谱、X射线荧光光谱、红外吸收光谱等方法对盱眙出土的夹纻胎漆器进行了分析研究.研究发现漆膜中的红色颜料和暗黑色颜料分别是HgS和CuS;漆灰的填料以粘土类物质为主,存在着加入骨灰的工艺;生漆被使用在漆灰制作、色漆调制等方面,起到了成膜剂的作用;麻胎之间采用漆灰作为胶合剂.     

残余奥氏体含量对马氏体高强钢滑动磨损性能的影响

对3种不同残奥(RA)含量的马氏体高强钢进行干滑动摩擦磨损试验, 研究RA含量对其磨损性能的影响. 利用扫描电镜、透射电镜、X射线衍射仪等对试验后的磨损表面及横截面显微组织进行表征. 结果表明, RA含量越高, 磨损表面越光滑, 摩擦系数和磨损率越小, 也即马氏体高强钢的耐磨性越好. 磨损引起的大应变使RA发生应变诱导马氏体相变, 导致硬度和硬化层厚度显著增大. RA含量最高的HT3试样的硬度提高了18.3%, 硬化层厚度达70μm. 相比RA含量低的试样, HT3试样表现出很好的耐磨性. 这是因为马氏体相变使硬度逐步增加, 抗裂纹萌生能力提高; 同时由于亚表面良好的韧性, 可延缓和阻止裂纹扩展, 使得点蚀和剥落不易形成. 因此, 要提高马氏体高强钢的耐磨性, 除了硬度要求外, 还需要考虑其亚表面韧性.