Experimental identification of physical parameters of fluid-filled pipes using acoustical signal processing

A method is formulated for the identification of an unknown physical parameter of a fluid-filled pipe using the measurement of sound speed in the pipe. The method uses a simple formula which provides the relationship between the sound speed and a few physical parameters of the pipe: thickness, diameter, wall material constants and fluid constants. Once the sound speed in the pipe is measured, the simple formula can be used to extract one of the unknown parameters providing the remaining ones are known.The sound speed in the pipe is measured using a 3-transducer array. In order to demonstrate the potential of the technique the results of several measurements obtained in a water-filled steel pipe are presented.The required accuracy of the measurement of sound speed and of the specification of known parameters is analysed. The accuracy depends on the unknown parameter which is to be identified. For example, if the pipe thickness is the unknown parameter, the other parameters have to be known within a very narrow margin of error. On the contrary, if the fluid properties have to be identified the needed accuracy of known parameters gets much lower.     

Stabilization of a K+-(bis-Cage-Annulated 20-Crown-6) Complex by Bidentate Picrate

Bis-cage-annulated 18-crown-6 and 20-crown-6 macrocyclic ethers (i.e., 1 and 2, respectively) have been synthesized, and their alkali metal picrate extraction profiles have been determined. Host system 1 proved to be a significantly more avid alkali metal cation complexant than 2 and somewhat more avid than 18-crown-6. Both 1 and 18-crown-6 display modest selectivity toward K⁺ and Rb⁺. A stable host–guest complex was prepared by slow evaporation of a CH₂Cl₂–hexane solution of an equimolar mixture of 2 and potassium picrate. The X-ray crystal structure of this complex reveals that picrate anion functions as a bidentate ligand therein. The gas-phase interaction energy between the 2 K⁺ complex and picrate anion was calculated to be ca. –64.9 kcal mol^–1, thereby indicating that participation of picrate anion as an additional bidentate ligand results in significant stabilization of complex 10.     

Solvent-free low-dimensional polymer electrolytes for lithium-polymer batteries

The development of solvent-free low-dimensional polymer electrolytes intended for use in solvent-free lithium batteries operating at ambient or sub-ambient temperatures is described. The synthetic routes to the amphiphilic polymers I having 5-alkoxy-3,4-phenylene units connected with oligoethoxy segments via polyester-ether or pure polyether links (abbrev. CmOn, m = 12, 16, 18, n = 1-5) and to the copolymers CmO1-CmOn are described. The structures, thermal properties and SAXS long spacings of their complexes with lithium salts (type A) and with long chain n-alkane or alkyl side chain intercalation (type B) are discussed. However, high ambient conductivities (10(-4)-10(-3) S cm(-1)) are observed in type C systems when a second copolymer based on polytetramethylene oxide segments (II) is incorporated as a microphase between the lamellae of I and serving as an ion bridge or "glue". DC polarization between Li electrodes also gives ambient conductivities >/=ca.10(-3) S cm(-1). In type D systems the I/II interface is stabilized by including a copolymer III, promoting high reproducibility in performance. Copolymers I of CmO1-CmO5 having CmO1 in excess give optimum conductivities with low temperature-dependence. This, together with molecular modeling, suggests uncoupled ion mobilities by hopping between small aggregates in the interlamellar spaces.     

Observations and spectral simulations of the7Li2 21 Σ u + →X 1 Σ g + transition

The⁷Li₂ 2¹ Σ _u ⁺ →X ¹ Σ _g ⁺ electronic transition has a bound-bound and a bound-free part due to the double minimum nature of the upper 2¹ Σ _u ⁺ state. We have studied this transition both experimentally and by performing spectral simulations. When inner well was excited the bound-free part at 4525 Å was observed due to the collisions between Li ₂ ^* and argon. We found that when levels above the barrier are excited the bound-free emission is strongly affected by collisional relaxation of Li ₂ ^* by Li atoms. Conditions for the observation of the bound-free part are discussed.     

Solid-phase synthesis of lipidated peptides

A new flexible and efficient methodology for the solid-phase synthesis of lipidated peptides has been developed. The approach is based on the use of previously synthesized building blocks and overcomes the limitations of previously reported methods, since long doubly lipidated peptides can be synthesized by using this route. Furthermore, it was thus possible to prepare a large number of N- and H-Ras peptides bearing a wide range of reporter and/or linking groups--efficient tools for the investigation of biological processes. In terms of efficiency and flexibility this solid-phase method is superior to the solution-phase synthesis. It gives pure peptides in multimilligram amounts within a much shorter time and with superior overall yield.     

Optimization of artificial neural networks used for retention modelling in ion chromatography

The aim of this work is the development of an artificial neural network model, which can be generalized and used in a variety of applications for retention modelling in ion chromatography. Influences of eluent flow-rate and concentration of eluent anion (OH-) on separation of seven inorganic anions (fluoride, chloride, nitrite, sulfate, bromide, nitrate, and phosphate) were investigated. Parallel prediction of retention times of seven inorganic anions by using one artificial neural network was applied. MATLAB Neural Networks ToolBox was not adequate for application to retention modelling in this particular case. Therefore the authors adopted it for retention modelling by programming in MATLAB metalanguage. The following routines were written; the division of experimental data set on training and test set; selection of data for training and test set; Dixon's outlier test; retraining procedure routine; calculations of relative error. A three-layer feed forward neural network trained with a Levenberg-Marquardt batch error back propagation algorithm has been used to model ion chromatographic retention mechanisms. The advantage of applied batch training methodology is the significant increase in speed of calculation of algorithms in comparison with delta rule training methodology. The technique of experimental data selection for training set was used allowing improvement of artificial neural network prediction power. Experimental design space was divided into 8-32 subspaces depending on number of experimental data points used for training set. The number of hidden layer nodes, the number of iteration steps and the number of experimental data points used for training set were optimized. This study presents the very fast (300 iteration steps) and very accurate (relative error of 0.88%) retention model, obtained by using a small amount of experimental data (16 experimental data points in training set). This indicates that the method of choice for retention modelling in ion chromatography is the artificial neural network.     

A versatile toolbox for variable DNA functionalization at high density

To broaden the applicability of chemically modified DNAs in nano- and biotechnology, material science, sensor development, and molecular recognition, strategies are required for introducing a large variety of different modifications into the same nucleic acid sequence at once. Here, we investigate the scope and limits for obtaining functionalized dsDNA by primer extension and PCR, using a broad variety of chemically modified deoxynucleotide triphosphates (dNTPs), DNA polymerases, and templates. All natural nucleobases in each strand were substituted with up to four different base-modified analogues. We studied the sequence dependence of enzymatic amplification to yield high-density functionalized DNA (fDNA) from modified dNTPs, and of fDNA templates, and found that GC-rich sequences are amplified with decreased efficiency as compared to AT-rich ones. There is also a strong dependence on the polymerase used. While family A polymerases generally performed poorly on "demanding" templates containing consecutive stretches of a particular base, family B polymerases were better suited for this purpose, in particular Pwo and Vent (exo-) DNA polymerase. A systematic analysis of fDNAs modified at increasing densities by CD spectroscopy revealed that single modified bases do not alter the overall B-type DNA structure, regardless of their chemical nature. A density of three modified bases induces conformational changes in the double helix, reflected by an inversion of the CD spectra. Our study provides a basis for establishing a generally applicable toolbox of enzymes, templates, and monomers for generating high-density functionalized DNAs for a broad range of applications.     

Preparation and Characterisation of Nano-Structured WO<Subscript>3</Subscript>-TiO<Subscript>2</Subscript> Layers for Photoelectrochromic Devices

Nano-structured WO₃-TiO₂ layers were prepared by the sol-gel route. To obtain transparent, porous and crack free layers up to 0.8 μ m with a single dipping cycle a templating strategy was used. As a template three-dimensionally network based on organically modified silane was introduced to the WO₃ and TiO₂ sols. The WO₃ layers were dip-coated onto the conductive glass substrate (TCO) and the TiO₂ layers on the top of the WO₃ layer. The morphology and the structure of the layers were determined by Scanning Electron Microscopy (SEM), High Resolution Transmission Electron Microscopy (HR-TEM), Energy Dispersive X-Ray Spectroscopy (EDXS), Auger and Infrared spectroscopy. SEM image of the WO₃-TiO₂ layer confirmed the nano-porosity of the layers and give the size of the particles of about 10 nm for TiO₂ and 30 nm for WO₃ layer. Further analysis indicated that the titanium sol penetrates the WO₃ layer. Particles in the WO₃ layer consist of a crystalline monoclinic WO₃ core surrounded by a 5–10 nm amorphous phase consisting of WO₃, TiO₂ and SiO₂. The WO₃-TiO₂ layers were used to assemble all solid state photoelectrochromic (PE) devices. Under 1 sun irradiation (1000 W/m²) the visible transmittance of the PE device changes from 62% to 1.6%. The colouring and bleaching processes last about 10 minutes.