Optically preamplified receiver performance due to VSB filtering for 40-Gb/s optical signals modulated with various formats

Optically preamplified receiver performance according to the vestigial sideband (VSB) filtering has been numerically investigated for 40-Gb/s optical signals modulated with nonreturn-to-zero, duobinary nonreturn-to-zero (NRZ), return-to-zero (RZ), carrier-suppressed RZ, and duobinary carrier-suppressed RZ formats. The VSB filtering enables the spectral widths of NRZ, duobinary NRZ, and RZ signals to be reduced without severe power penalties at the receiver. On the other hand, carrier-suppressed RZ and duobinary carrier-suppressed RZ signals have no large advantages over VSB filtering because of the characteristics of their signals. Our results suggest that RZ signals are the most suitable modulation format for VSB filtering, without considering the filter loss, because of the tolerance of the intersymbol interference and a large spectral width. However, duobinary NRZ signals are the most suitable modulation format for VSB filtering, considering the filter loss, because of their narrow spectral width.     

High-gain pseudomorphic InGaAs base ballistic hot-electron device

A high-gain ballistic hot-electron device is described. The GaAs-AlGaAs heterostructure device, with a 21-mm-thick pseudomorphic In _0.12Ga_0.88As base, had a current gain of 27 at 77 K and 41 at 4.2 K. As characteristically seen in ballistic devices, transfer into the L valley limited the maximum gain. The Γ-L valley separation in the strained In_0.12Ga_0.88As was estimated to be about 380 meV     

Investigation into Polarization of Unloaded and Loaded Microstrip Square-Ring Antennas

The polarization characteristic of unloaded and loaded square-ring microstrip antennas is investigated. Several different loading types like single-stub, dual-stub, notch, gap and shorting-pin are considered and their effects are studied. Loading enables feeding using a 50-Omega probe. The simulation and measurement results show that the loading techniques excite a loaded TMy ₁₁ mode that is orthogonal to the unloaded TMx ₁₁ mode. This indicates that by loading the ring antenna its polarization can be switched adaptively. However, the purity of the loaded and unloaded modes depends on the loading type. For some loading types like gap and shorting-pin, the excitation of the unloaded mode seems negligible, in comparison to the loadings by stub and notch. For the stub and notch loaded antennas the unloaded mode is also present, and its excitation efficiency is frequency dependent. Thus, their polarization plane, which is due to both loaded TMy ₁₁ and unloaded TMx ₁₁ modes, also becomes frequency dependant. The results of this investigation can be useful in selecting the loading methods for high-impedance microstrip ring antennas, and control of their impedance and polarization. The knowledge of the antenna polarization is essential in communications, and its dependence on the loading type can be used as an important parameter in design of adaptive antennas and sensors.     

Performance modeling and evaluation of data/voice services in wireless networks

Application-level performance is a key to the adoption and success of the CDMA 2000. To predict this performance in advance, a detailed end-to-end simulation model of a CDMA network is built to include application traffic characteristics, network architecture, network element details using the proposed simulation methodology. We assess the user-perceived application performance when a RAN and a CN adopt different transport architectures such as ATM and IP. To evaluate the user-perceived quality of voice service, we compare the end-to-end packet delay for different vocoder schemes such as G.711, G.726 (PCM), G.726 (ADPCM), and vocoder bypass scheme. By the simulation results, the vocoder bypass scenario shows 30% performance improvement over the others. We also compare the quality of voice service with and without DPS scheduling scheme. We know that DPS scheme keep the voice delay bound even if the service traffic is high. For data packet performance, HTTP v.1.1 shows better performance than that of HTTP v.1.0 due to the pipelining and TCP persistent connection. We may conclude that IP transport technology is better solution for higher FER environment since the packet overhead of IP is smaller than that of ATM for web browsing data traffic, while it shows opposite effect to the small size voice packet in RAN architecture. We show that the 3G-1X EV-DO system gives much better packet delay performance than 3G-1X RTT. The main conclusion is that end-to-end application-level performance is affected by various elements and layers of the network and thus it must be considered in all phases of the development process. Jae-Hyun Kim He received the B.S., M.S., and Ph.D. degrees, all in computer science and engineering, from Hanyang University, Ansan, Korea, in 1991, 1993, and 1996 respectively. In 1996, he was with the Communication Research Laboratory, Tokyo, Japan, as a Visiting Scholar. From April 1997 to October 1998, he was a post-doctoral fellow at the department of electrical engineering, University of California, Los Angeles. From November 1998 to February 2003, he worked as a member of technical staff in Performance Modeling and QoS management department, Bell laboratories, Lucent Technologies, Holmdel, NJ. He has been with the department of electrical engineering, Ajou University, Suwon, Korea, as an assistant professor since 2003. His research interests include QoS issues and cross layer optimization for high-speed wireless communication. Dr. Kim was the recipient of the LGIC Thesis Prize and Samsung Human-Tech Thesis Prize in 1993 and 1997, respectively. He is a member of the Korean Institute of Communication Sciences (KICS), Korea Institute of Telematics and Electronis (KITE), Korea Information Science Society (KISS), and IEEE. Hyun-Jin Lee received the B.S. degree in electrical engineering from Ajou University, Suwon, Korea, in 2004, and is working toward the M.S. degree and Ph. D. degree in electrical engineering at Ajou University. He has been awarded Samsung Human-Tech Thesis Prize in 2004. His research interests QoS, especially network optimization and wireless packet scheduling. He is a member of the KICS. Sung-Min Oh received the B.S. and M. S. degrees in electrical engineering form Ajou University, Suwon, Korea, in 2004, and is working toward the Ph. D. degree in electrical engineering at Ajou University. His research interests QoS performance analysis and 4G network. He is a member of the KICS. Sung-Hyun Cho received his B.S., M.S., and Ph.D. in computer science and engineering from Hanyang University, Korea, in 1995, 1997, and 2001, respectively. From 2001 to 2005, he has been with Samsung Advanced Institute of Technology, where he has been engaged in the design and standardization of MAC and upper layers of B3G, IEEE 802.16e, and WiBro systems. He is currently a MAC part leader in the telecommunication R&D center of Samsung Electronics. His research interests include 4G air interface design, radio resource management, cross layer design, and handoff in wireless systems.     

Rapid DNA hybridization analysis using a PDMS microfluidic sensor and a molecular beacon.

A rapid DNA analysis has been developed based on a fluorescence intensity change of a molecular beacon in a PDMS microfluidic channel. Recently, we reported a new analytical method of DNA hybridization involving a PDMS microfluidic sensor using fluorescence energy transfer (FRET). However, there are some limitations in its application to real DNA samples because the target DNA must be labelled with a suitable fluorescent dye. To resolve this problem, we have developed a new DNA microfluidic sensor using a molecular beacon. By monitoring the change in the restored fluorescence intensity along the channel length, it is possible to rapidly detect any hybridization of the molecular beacon to the target DNA. In this case, the target DNA does not need to be labelled. Our experimental results demonstrate that this microfluidic sensor using a molecular beacon is a promising diagnostic tool for rapid DNA hybridization analysis.     

Collision-Free Interleaver Composed of a Latin Square for Parallel-Architecture Turbo Codes

In parallel-architecture turbo codes, the constituent interleavers must avoid memory collision. This paper proposes a collision-free interleaver structure composed of a Latin square (LS) and pre-designed interleavers. Our proposed interleavers can be easily optimized for various information block sizes and for various degrees of parallelism. Their performances were evaluated by computer simulation.     

A parallel cell‐based DSMC method on unstructured adaptive meshes

A parallel DSMC method based on a cell‐based data structure is developed for the efficient simulation of rarefied gas flows on PC‐clusters. Parallel computation is made by decomposing the computational domain into several subdomains. Dynamic load balancing between processors is achieved based on the number of simulation particles and the number of cells allocated in each subdomain. Adjustment of cell size is also made through mesh adaptation for the improvement of solution accuracy and the efficient usage of meshes. Applications were made for a two‐dimensional supersonic leading‐edge flow, the axi‐symmetric Rothe's nozzle, and the open hollow cylinder flare flow for validation. It was found that the present method is an efficient tool for the simulation of rarefied gas flows on PC‐based parallel machines. Copyright © 2004 John Wiley & Sons, Ltd.     

Study on Contamination Control for Yield Enhancement in the Manufacturing Line of Cellular Phone Modules

Practical studies on the method of contamination control for yield enhancement in the cellular phone modules production line were carried out. A contamination control method was proposed, consisting of data collection, data analysis, improvement action, verification, and implementation of control. The partition check method and the composition analysis for data collection and data analysis were respectively used in the cellular phone modules manufacturing process, and these methods were evaluated by the variation of yield loss before and after implementing the actions for improvement. In the partition check method, the critical process step was selected, and yield loss reduction through improvement actions was observed, whereas in the composition analysis, critical sources were selected, and yield loss reduction through improvement actions was investigated. From the results, it is concluded that the partition check and the composition analysis are effective solutions for contamination control in cleanroom production lines.     

Improved strained HEMT characteristics using double-heterojunctionIn0.65Ga0.35As/In0.52Al0.48As design

The DC and microwave properties of strained In_0.65Ga _0.35As/In₀₅₂Al_0.48As HEMTs (high electron-mobility transistors) with double-heterojunction design are presented. The high sheet carrier density and good carrier confinement give rise to excellent device performance with very low output conductance. For 1×150-μm² long-gate HEMTs, the measured cutoff frequency f_T and maximum frequency of oscillation f_max are as high as 37 and 66 GHz, respectively     

Synthesis and characterization of novel perfluorinated polyimides with 3D‐controlled structures for photonic applications

We have designed and synthesized novel perfluorinated polyimides with 3D controlled structure. At first, we successfully developed the new synthetic routes to diamines with pendant bulky perfluorinated aromatic units in a multi‐step synthetic procedure. Novel perfluorinated polyimides were prepared in a two‐step reaction in N‐methyl‐2‐pyrrolidinone (NMP) solution: The first step was for the synthesis of polyamic acids (PAAs) and the second reaction was for the imidization of PAA. The polymer yield was over 89% and the inherent viscosity of PAAs was in the range of 0.24–0.36 dL/g. The thin films were prepared by spin‐coating the PAA solution in NMP onto various substrates such as a Si wafer or a KBr pellet, dried at 80 °C and further cured at 230 °C. The resultant polyimides are thermally stable over 400 °C. The refractive index and birefringence of the resultant polyimides are 1.5858–1.6452 and 0.01–0.005, respectively. The refractive index of polyimide decreases with increasing the fluorine content. The copolymerization and the ether linkages into the backbone reduce the birefringence of polyimides. Surprisingly, the pendant ether linkage is not a crucial factor in reducing the polyimide birefringence. Their birefringence is comparatively very low, compared with that of previous polyimides. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 1326–1342, 2006