High-performance MIM capacitor using ALD high-k HfO/sub 2/-Al/sub 2/O/sub 3/ laminate dielectrics

For the first time, we successfully fabricated and demonstrated high performance metal-insulator-metal (MIM) capacitors with HfO/sub 2/-Al/sub 2/O/sub 3/ laminate dielectric using atomic layer deposition (ALD) technique. Our data indicates that the laminate MIM capacitor can provide high capacitance density of 12.8 fF//spl mu/m/sup 2/ from 10 kHz up to 20 GHz, very low leakage current of 3.2 /spl times/ 10/sup -8/ A/cm/sup 2/ at 3.3 V, small linear voltage coefficient of capacitance of 240 ppm/V together with quadratic one of 1830 ppm/V/sup 2/, temperature coefficient of capacitance of 182 ppm//spl deg/C, and high breakdown field of /spl sim/6 MV/cm as well as promising reliability. As a result, the HfO/sub 2/-Al/sub 2/O/sub 3/ laminate is a very promising candidate for next generation MIM capacitor for radio frequency and mixed signal integrated circuit applications.     

Serially concatenated space-time codes with iterative decoding and performance limits of block-fading channels

This work considers space-time channel coding for systems with multiple-transmit and a single-receive antenna, over space uncorrelated block-fading (quasi-static) channels. Analysis of the outage probability over such channels reveals the existence of a threshold phenomenon. The outage probability can be made arbitrary small by increasing the number of transmit antennas, only if the E/sub b//N/sub 0/ is above a threshold which depends on the coding rate. Furthermore, it is shown that when the number of transmit antennas is increased, the /spl epsi/-capacity of a block-fading Rayleigh channel tends to the Shannon capacity of an additive white Gaussian noise channel. This paper also presents space-time codes constructed as a serial concatenation of component convolutional codes separated by an interleaver. These schemes provide full transmit diversity and are suitable for iterative decoding. The rate of these schemes is less than 1 bit/s/Hz, but can be made arbitrary close to 1 bit/s/Hz by the use of Wyner-Ash codes as outer components. Comparison of these schemes with structures from literature shows that performance gains can be obtained at the expense of a small decrease in rate. Computer simulation results over block-fading Rayleigh channels show that the frame-error rate of several of these schemes is within 2-3 dB from the theoretical outage probability.     

High-resolution photonics-based interference suppression filter with wide passband

A new topology for a photonic signal processor, which overcomes the basic recursive frequency response problem that limits the passband range, is presented. The structure is based on a new multiple-wavelength offset-cavity structure that is cascaded with a series of unbalanced delay line structures. This not only can synthesize a very narrow notch response with good shape factor but also permits a multifold extension of the free spectral range (FSR) and passband width. Results on the interference mitigation filter demonstrate a stopband of 1% of center frequency and a fourfold increase in the FSR and passband width, while also having a very small shape factor, in excellent agreement with predictions.     

An investigation of sugar extraction methods and the use of microwave power for date syrup processing: efficiency and color related considerations.

This study investigates the effect of extraction methods on the color of date syrup and the potential use of microwave power for syrup processing. Sugar solutions were extracted from dates by boiling, soaking and blending. Color and sugar content of the extracted solutions were measured, and the percentage of sugar extracted form the total fruit sugar determined. Boiling was found to be the most efficient method of extraction whereby 74% of total samples sugar was extracted. In contrast, only 54.2% of fruit sugar was extracted by blending and 42% by soaking. In addition, solutions extracted by soaking and blending had a foaming problem in the subsequent concentration process. The extraction method had no effect on the product final color. The extracted solution was concentrated using two heating methods: conventional and microwave heating at a 600 W capacity and a frequency of 2450 MHz applied at three power levels: 10, 7, and 6. In the heating process, 180 minutes were needed to achieve a 77% degrees Brix using convective heating, while it took 81, 138, and 166 minutes of microwave heating at power level 10, 7, and 6, respectively to achieve the same concentration. Water activity of the syrup was measured within a sugar content range of 50 to 80% degrees Brix and the sugar concentration at which the product is shelf stable was determined at 76%.     

Reliability investigation of 0.07-/spl mu/m InGaAs-InAlAs-InP HEMT MMICs with pseudomorphic In/sub 0.75/Ga/sub 0.25/As channel

The authors have investigated the reliability performance of G-band (183 GHz) monolithic microwave integrated circuit (MMIC) amplifiers fabricated using 0.07-/spl mu/m T-gate InGaAs-InAlAs-InP HEMTs with pseudomorphic In/sub 0.75/Ga/sub 0.25/As channel on 3-in wafers. Life test was performed at two temperatures (T/sub 1/ = 200 /spl deg/C and T/sub 2/ = 215 /spl deg/C), and the amplifiers were stressed at V/sub ds/ of 1 V and I/sub ds/ of 250 mA/mm in a N/sub 2/ ambient. The activation energy is as high as 1.7 eV, achieving a projected median-time-to-failure (MTTF) /spl ap/ 2 /spl times/ 10/sup 6/ h at a junction temperature of 125 /spl deg/C. MTTF was determined by 2-temperature constant current stress using /spl Delta/G/sub mp/ = -20% as the failure criteria. The difference of reliability performance between 0.07-/spl mu/m InGaAs-InAlAs-InP HEMT MMICs with pseudomorphic In/sub 0.75/Ga/sub 0.25/As channel and 0.1-/spl mu/m InGaAs-InAlAs-InP HEMT MMICs with In/sub 0.6/Ga/sub 0.4/As channel is also discussed. The achieved high-reliability result demonstrates a robust 0.07-/spl mu/m pseudomorphic InGaAs-InAlAs-InP HEMT MMICs production technology for G-band applications.     

Hot carrier analysis in low-temperature poly-Si thin-film transistors using pico-second time-resolved emission microscope

We have analyzed degradation of N-channel thin-film-transistor (TFT) under dynamic stress using a pico-second time-resolved emission microscope. We have successfully detected emission at pulse fall edge for the first time. Emission intensity increased with the decrease of pulse fall time. As the degradation depended on the pulse fall time, this dependence clearly illustrates that hot electrons are the dominant cause of the degradation under dynamic stress. Based on these dependences, we proposed a model considering electron traps in the poly-Si.     

Bandpass filters with reconfigurable transmission zeros using varactor-tuned tapped stubs

In this letter, bandpass filters with one or two tunable transmission zeros are proposed. The reconfigurable transmission zeros are implemented through varactors in combination with tapped quarter-wavelength stubs. Based on mixed mode simulations including EM simulation and circuit simulation, the proposed filters were designed and fabricated on low-cost FR4 board. The measurement results verified the design concepts.     

Towards intelligent dressing

The aim of this article is to state the principles of an intelligent monitoring and control system for the grinding machine, comprising the dressing process as well as grinding stability.