Evidences of phase separation in moisture‐cured poly(urethane urea)s by means of temperature modulated differential scanning calorimetry

The degree of phase separation in several moisture‐cured poly(urethane urea)s (PUUs) was studied by FTIR spectroscopy, wide angle X‐ray diffraction (WAXD), and temperature‐modulated differential scanning calorimetry (TMDSC). This latter technique was shown to be particularly useful in analysing the degree of phase separation in PUU polymers. Both phase mixing and phase segregation coexisted in the PUUs and the degree of phase separation increased as the urea hard segment (HS) content in the PUU increased. The maximum solubility of urea HSs into the polyol soft segments (SSs) was achieved for 50 wt % urea HS content in diol‐based PUUs, whereas for triol‐based PUUs the highest solubility between HS and SS was reached for lower urea HS amount. Finally, the higher the urea HS content the higher the extent of phase separation in the PUU. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 3034–3045, 2007     

Amplitude des oscillations d'ondes solitaires généralisées

Various physical systems of dispersive waves admit solutions in the form of generalized solitary waves. Such waves result from the resonance between a long localized wave and short periodic oscillations. Many estimates (rigorous and numerical) have been given for the amplitude of the ripples in the tail of the generalized solitary wave when its central part has a sech² shape. This Note provides estimates (not yet rigorous) for the ripple amplitude when the central part is flat and wide. To cite this article: C. Fochesato, F. Dias, C. R. Acad. Sci. Paris, Ser. I 337 (2003).     

Novel acrylic macromonomer with amphiphilic character derived from Triton X‐100: Radical copolymerization with methyl methacrylate and thermal properties

This article explores the synthesis of a novel methacrylic macromonomer with an amphiphilic character derived from poly(ethylene glycol) tert‐octylphenyl ether (MT) and its respective homopolymer. To know their reactivity in radical copolymerization reactions with methyl methacrylate (MMA), a model monomer (MTm) was synthesized to determine the reactivity ratios and compare them with the low molar fractions of copolymers of MT with MMA because they were difficult to isolate. They were r_MTm = 0.97 and r_MMA = 0.95. The compositional diagrams when representing the weight fraction of MT and MTm in the feed and the copolymer suggested that a clear correlation exists between the experimental points of the model monomer MTm and the macromonomer MT ones, suggesting that the length of the side poly(ethylene oxide) chain does not affect the reactivity of the methacrylic double bond in the prepared monomers for this type of polymerization reaction. The reactivity ratios of the copolymers have a tendency for the formation of random or Bernoullian copolymers. The glass‐transition temperatures (T_g's) of the prepared copolymers were determined by differential scanning calorimetry, deviated from the Fox equation, and discussed on the basis of treatments that consider the influence of the monomeric units along the copolymer chains, determining the T_g of the corresponding alternating dyads. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 1641–1649, 2003     

Hydrophilic and hydrophobic copolymer systems based on acrylic derivatives of pyrrolidone and pyrrolidine

This article deals with the synthesis of hydrophilic methacrylic monomers derived from ethyl pyrrolidone [2‐ethyl‐(2‐pyrrolidone) methacrylate (EPM)] and ethyl pyrrolidine [2‐ethyl‐(2‐pyrrolidine) methacrylate (EPyM)] and their respective homopolymers. For the determination of their reactivity in radical copolymerization reactions, both monomers were copolymerized with methyl methacrylate (MMA), the reactivity ratios being calculated by the application of linear and nonlinear mathematical methods. EPM and MMA had ratios of r_EPM = 1.11 and r_MMA = 0.76, and this indicated that EPM with MMA had a higher reactivity in radical copolymerization processes than vinyl pyrrolidone (VP; r_VP = 0.005 and r_MMA = 4.7). EPyM and MMA had reactivity ratios of r_EPyM = 1.31 and r_MMA = 0.92, and this implied, as for the EPM–MMA copolymers, a tendency to form random or Bernoullian copolymers. The glass‐transition temperatures of the prepared copolymers were determined by differential scanning calorimetry (DSC) and were found to adjust to the Fox equation. Total‐conversion copolymers were prepared, and their behavior in aqueous media was found to be dependent on the copolymer composition. The swelling kinetics of the copolymers followed water transport mechanism case II, which is the most desirable kinetic behavior for a swelling controlled‐release material. Finally, the different states of water in the hydrogels—nonfreezing water, freezing bound water, and unbound freezing water—were determined by DSC and found to be dependent on the hydrophilic and hydrophobic units of the copolymers. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 395–407, 2003     

Influence of the loading path on the strength of fiber-reinforced composites subjected to transverse compression and shear

The influence of the loading path on the failure locus of a composite lamina subjected to transverse compression and out-of-plane shear is analyzed through computational micromechanics. This is carried out using the finite element simulation of a representative volume element of the microstructure, which takes into account explicitly fiber and matrix spatial distribution within the lamina. In addition, the actual failure mechanisms (plastic deformation of the matrix and interface decohesion) are included in the simulations through the corresponding constitutive models. Two different interface strength values were chosen to explore the limiting cases of composites with strong or weak interfaces. It was found that failure locus was independent of the loading path for the three cases analyzed (pseudo-radial, compression followed by shear and shear followed by compression) in the composites with strong and weak interfaces. This result was attributed to the fact that the dominant failure mechanism in each material was the same in transverse compression and in shear. Failure is also controlled by the same mechanisms under a combination of both stresses and the failure locus depended mainly on the magnitude of the stresses that trigger fracture rather than in the loading path to reach the critical condition.     

Oscillator strength of a two-dimensional D ion in magnetic fields

In the present paper we determine the oscillator strength of two-dimensional (2D) D⁻ ions under the influence of a static magnetic field. The results are important for the analysis of the optical transitions observed in semiconductor quantum wells. We have applied the ab initio procedure Hyperspherical Adiabatic Approach, based on the use of hyperspherical coordinates. This approach uses an adiabatic separation of the total wave function that allows accurate energies determination from molecular-like potential curves. The convergence is obtained in a systematic way by the inclusion of non-adiabatic couplings without the need of adjustable parameters.     

Annealing effects on the magnetization of Co–Ni–B amorphous nanoparticles

Chemically prepared (Co_xNi_1−x)_1−yB_y (x=0.5, 0.75, 1; y≈0.4) amorphous fine particles were characterized by X-ray diffraction, DTA and TGA, and in situ magnetic measurement as a function of annealing temperature in an inert atmosphere. Magnetic measurement performed in as-prepared and 150°C annealed samples shows an increase of the saturation magnetization and magnetic moment after thermal treatment. Room temperature magnetization increases by factors of 3.5, 1.8, and 1.5, for x=0.5, 0.75, and 1, respectively. These measurements may indicate a local re-ordering of the amorphous phase at temperatures much lower than the full crystallization temperature.     

Infrared and Raman spectroscopic investigation of Eu3+-doped mono and Di-urethanesil hybrid siliceous materials

The general features of two series of sol-gel derived materials, designatedurethanesils (Ut), have been investigated by infrared and Raman spectroscopies with the goal of elucidating the chemical environment of the Eu³⁺ cations. The host frameworks of the two families of ormolytes studied have been represented by m-Ut(350) and d-Ut(300), where m stands for mono, d stands for di, 350 and 300 are the average molecular weights of the organic precursors (poly(ethylene glycol) methyl ether, PEGME, and poly(ethylene glycol), PEG, respectively). The hybrid matrix of the mono-xerogels is composed by a siliceous backbone bonded by means of urethane linkages (-NHC (=O)O-) to pendant methyl end capped oligopolymer chains with approximately 7 oxyethylene units, whereas that of the di-xerogels is based on a siliceous network grafted through urethane groups to both ends of poly(oxyethylene) segments containing about 6 (OCH₂CH₂) repeat units. Both classes of materials have been doped with europium triflate (Eu(CF₃SO₃)₃). The doped samples have been identified by m-Ut(350)_nEu(CF₃SO₃)₃ and d-Ut(300)_nEu(CF₃SO₃), where n is the molar ratio of (OCH₂CH₂) repeat units per Eu³⁺ ion. Materials with n ranging from ∞ to 5 have been analyzed. The spectral data obtained provide evidence that the cations begin to coordinate to the ether oxygen atoms of the oligopolymer chains at n=40 in the mono-urethanesils and at n=10 in the di-urethanesils. In mono-urethanesils samples with n>40 and in di-urethanesils materials with n>10, the Eu³⁺ coordinate exclusively to the carbonyl oxygen atoms of the urethane linkages. Paper presented at the 8th EuroConference on Ionics, Carvoeiro, Algarve, Portugal, Sept. 16–22, 2001.