排序方式: 共有22条查询结果,搜索用时 15 毫秒
1.
上海光源X射线成像光束线采用多极扭摆器(wiggler)作为辐射光源, 提出一种劳厄双弯晶单色器的设计方案. 计算结果显示, 可获得固定出口的平行单色光束, 能量调谐范围覆盖19—120keV, 在33keV时, 输出光子通量及通量密度分别为1.9×1013phs/s和3.8×1010phs/s/mm2. 分析了劳厄晶体的聚焦及单色化性能, 计算了输出光子通量及单色器的热负载情况. 与传统的双平晶方案相比, 本设计在获得高通量和解决热负载等方面有明显的优越性, 并能有效控制热形变. 相似文献
2.
Due to the low absorption contrast of plant tissues, traditional x-ray radiography has not been included in the microscopic techniques used in the identification of traditional Chinese medicines (TCMs). With the development of x-ray phase contrast imaging (XPCI) in recent years, weakly absorbing materials could also be imaged by x- rays. Here we investigate microstructures of TCMs utilizing XPCI based on a nano-focus x-ray tube. The results demonstrated that XPCI is capable of revealing the microstructures of TCMs used as judging criteria in the identification of TCMs. The major advantages of the new method are nondestructivity, no special demand for sample preparation and suitability for thick samples. 相似文献
3.
4.
在所有的相衬成像方法中,X射线同轴轮廓成像由于光路简单、不需要任何光学元件而备受关注.其缺点是无法直接消除散射的影响,从而限制了它在生物医学等领域中的应用.利用数字模拟方法研究了引入散射前后轮廓像的质量随样品到探测器距离的变化情况.模拟结果表明直接轮廓成像存在一个最佳成像距离,因而无法通过改变样品到探测器距离来减小散射的影响.利用定量相衬成像不受成像距离限制的特点,研究了远距离成像时散射的影响.结果表明,样品到探测器的距离增大到一个临界值时,散射对重构像的影响可降到一个极值,此时成像质量得到了明显改善.
关键词:
散射
X射线同轴轮廓成像
定量相衬成像 相似文献
5.
We report a design for one nanometer X-ray focusing by a complex refractive lens, which is capable of focusing 20 keV X-rays down to a lateral size of 0.92 nm (full-width at half-maximum (FWHM)) and an axial size of 98 nm (FWHM) with intensity gain of 49050. This complex refractive lens is comprised of a series of kinoform lenses, whose aperture is gradually matched to the converging trace of the X-ray beam so as to increase the numerical aperture (NA). The theoretical principle of the proposed complex refractive lens is presented. The NAs of these lenses are calculated. The numerical simulation results demonstrate that the proposed design can focus the X-ray beam into sub-nanometer while remaining high gain. 相似文献
7.
利用微聚焦管硬x射线光源进行同轴位相衬度成像实验,所用的光源聚焦尺寸最小可达0.5μm.根据微聚焦硬x射线管的光学传递函数,对光源尺寸、相干长度等因素对成像分辨率的影响进行了分析.对新鲜的未经任何处理的生物样品进行了位相衬度成像,分辨率在10μm左右,并和吸收衬度成像进行了对比.实验结果表明利用微聚焦管作为硬x射线光源,多色硬x射线位相衬度成像可以得到比吸收衬度成像高得多的分辨率.
关键词:
位相衬度成像
微聚焦管x射线源
吸收衬度成像
光学传递函数 相似文献
8.
9.
Kinoform单透镜可以高效聚焦硬X射线至纳米量级, 在X射线纳米显微学和纳米光谱学领域有着重要的应用前景. 基于衍射光学和傅里叶光学理论, 给出了X射线经由Kinoform单透镜聚焦的物理模型, 基于数值模拟, 研究了不同材料、光子能量、台阶数量和顶点曲率半径对Kinoform单透镜聚焦性能的影响. 结果表明, 孔径为1 mm的Kinoform单透镜对30 keV的X射线聚焦, 可以得到14 nm焦斑、62 μm焦深, 且可实现4个量级的光强增益和大于30%的光强透过率. 相似文献
10.
在同步辐射X射线成像中,时常会出现对比度不高或对比度不均匀的问题,这将导致图像中样品的一些细节信息难以被观察和分析。针对这一问题,提出一种X射线图像对比度增强的算法。该算法以同态滤波为核心,结合图像降噪预处理及灰度调整,以现图像的对比度增强,并提高图像质量。编写程序实现该算法,并通过对分辨率靶图像和海洋鱼类样品的X射线图像进行测试。结果表明,该算法可以很好地增强灰度分布不均匀的低对比度X射线图像,使样品信息显示更清晰,灰度分布更均匀。同时,对X射线图像的降噪效果明显。 相似文献