Characterization of low molecular weight hydrocarbon oligomers by laser desorption/ionization time-of-flight mass spectrometry using a solvent-free sample preparation method.

A new solvent-free sample preparation method using silver trifluoroacetate (AgTFA) was developed for the analysis of low molecular weight paraffins and microcrystalline waxes by laser desorption/ionization time-of-flight mass spectrometry (LDI-TOFMS). Experiments show that spectral quality can be enhanced by dispersing AgTFA directly in liquid paraffins without the use of additional solvents. This preparation mixture is applied directly to the MALDI probe. Solid waxes could be examined by melting prior to analysis. The method also provides sufficiently reproducible spectra that peak area ratios between mono- and bicyclic alkane peaks indicated variations in the cycloalkane content of paraffin samples. Dehydrogenation of hydrocarbons observed during the desorption/ionization process was studied by analysis of alkane standards.     

On a category of module bundles

It is shown, that the category ℰ _A (X) ofA-bundles over a topological spaceX is an additive pseudo-Abelian category for each Waelbroeck algebraA. This research was supported by Greek State Scholarship Foundation and Estonian Science Foundation grant 6205.     

Experimental investigation and theoretical modeling of liquid entrainment in a horizontal tee with a vertical-up branch

This article describes a comprehensive literature review of liquid entrainment in horizontal pipes with vertical-up branches. Deficiencies in the available data and correlations were identified. The Air–water Test Loop for Advanced Thermal–hydraulic Studies (ATLATS) was constructed and entrainment onset and steady-state data were collected for a wide range of flow conditions. Using new insights gained from experimental testing, the authors developed a model for predicting the onset of entrainment and steady-state entrainment rate. Previously published correlations, along with the new model, are compared against all available data. The new model shows very good agreement with the onset data, but is not very good at predicting branch quality at high liquid flow rates.     

Metallo‐supramolecular block copolymer micelles: Improved preparation and characterization

Micelles prepared from amphiphilic block copolymers in which a poly(styrene) segment is connected to a poly(ethylene oxide) block via a bis‐(2,2′:6′,2″‐terpyridine‐ruthenium) complex have been intensely studied. In most cases, the micelle populations were found to be strongly heterogeneous in size because of massive micelle/micelle aggregation. In the study reported in this article we tried to improve the homogeneity of the micelle population. The variant preparation procedure developed, which is described here, was used to prepare two “protomer”‐type micelles: PS₂₀‐[Ru]‐PEO₇₀ and PS₂₀‐[Ru]‐PEO₃₇₅. The dropwise addition of water to a solution of the compounds in dimethylformamide was replaced by the controlled addition of water by a syringe pump. The resulting micelles were characterized by sedimentation velocity and sedimentation equilibrium analyses in an analytical ultracentrifuge and by transmission electron microscopy of negatively stained samples. Sedimentation analysis showed virtually unimodal size distributions, in contrast to the findings on micelles prepared previously. PS₂₀‐[Ru]‐PEO₇₀ micelles were found to have an average molar mass of 318,000 g/mol (corresponding to 53 protomers per micelle, which is distinctly less than after micelle preparation by the standard method) and an average hydrodynamic diameter (d_h) of 18 nm. For PS₂₀‐[Ru]‐PEO₃₇₅ micelles, the corresponding values were M = 603,000 g/mol (31 protomers per micelle) and d_h = 34 nm. The latter particles were found to be identical to the “equilibrium” micelles prepared in pure water. Both micelle types had a very narrow molar mass distribution but a much broader distribution of s values and thus of hydrodynamic diameters. This indicates a conformational heterogeneity that is stable on the time scale of sedimentation velocity analysis. The findings from electron microscopy were in disagreement with those from the sedimentation analysis both in average micelle diameter and in the width of the distributions, apparently because of imperfections in the staining procedure. The preparation procedure described also may be useful in micelle formation from other types of protomers. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 4458–4465, 2004     

Concerning seven and eight mutually orthogonal Latin squares

In this paper, three new direct Mutually Orthogonal Latin Squares (MOLS) constructions are presented for 7 MOLS(24), 7 MOLS(75) and 8 MOLS(36); then using recursive methods, several new constructions for 7 and 8 MOLS are obtained. These reduce the largest value for which 7 MOLS are unknown from 780 to 570, and the largest odd value for which 8 MOLS are unknown from 1935 to 419. © 2003 Wiley Periodicals, Inc.     

Surface free energies of electroless Ni–P based composite coatings

Surface free energy of a solid surface gives a direct measure of intermolecular interactions at interfaces and has a strong influence on adsorption and adhesion behaviour. However few data are available for the surface free energies of electroless Ni–P based composition coatings. In this paper, the electroless Ni–P, Ni–P-surfactant, Ni–Cu–P, Ni–P–PTFE and Ni–Cu–P–PTFE composite coatings were prepared under various coating conditions. The chemical compositions, surface morphology and thickness of the coatings were measured using an energy dispersive X-ray microanalysis (EDX), a scanning electron microscope (SEM) and a digital micrometer respectively. The contact angles of water, diiodomethane and ethylene glycol on the coatings were measured automatically using dataphysics OCA-20 contact angle analyser. The surface free energy of the coatings and their components (e.g. dispersion, polar or acid/base portions) were calculated using various methods. The experimental results showed that the incorporation of surfactant or PTFE particles into Ni–P matrixes has a significant influence on the surface free energy of the coatings, while the incorporation of copper into Ni–P matrixes has no significant influence on the surface free energy of the coatings.