Three-dimensional atom probe study of the segregation behaviour of Ni91Pt9 alloy after sputtering

To investigate local ordering and segregation phenomenon in a Ni91Pt9-alloy after sputtering and annealing a 3D optical atom probe (OAP) has been used. The specimen tips have been prepared from polycrystalline samples. To sputter the samples a separate preparation chamber with a scannable Ar-sputter-gun is connected to the OAP vessel. When necessary, the sample can be electrically heated to induce segregation and cure the altered layer. After a heat treatment of a Ni91 at. %Pt 9 at.% specimen at 1100 K the surface of a (111)-oriented specimen is enriched in platinum by a factor of two in relation to the bulk. The phenomenon of short-range ordering has been investigated on the surface and in the subsurface volume. A 3D reconstruction of this annealed NiPt specimen shows regions with high concentration of platinum that gives an indication at short-range ordering. Uniform sputtering of the tip without a heat treatment induces a decisive depletion of Pt on the surface and the following subatomic layers. The atom-probe results of specimens in thermal equilibrium are in close agreement to further surface sensitive results obtained from Ion Scattering Spectroscopy (ISS) and Auger Electron Spectroscopy (AES).     

Miscibility of bisphenol-A polycarbonate with poly(methyl methacrylate)

The miscibility of bisphenol-A polycarbonate (PC) with poly(methyl methacrylate) (PMMA) has been reexamined using differential scanning calorimetry (DSC) and optical indications for phase separation on heating, i.e., lower critical solution temperature (LCST) behavior. Various methods have been used to prepare the blends including methylene chloride (CH₂Cl₂) and tetrahydrofuran (THF) solution casting, melt mixing, and precipitation of PC and PMMA simultaneously from THF solution by using the nonsolvents methanol and heptane. It is shown that the resulting phase behavior for PC/PMMA blends is strongly affected by the blend preparation method. However, these blends are miscible over the whole blend composition range (unambiguous single composition-dependent T_g's and LCST behavior) when prepared by precipitation from solution using heptane as the nonsolvent. To the contrary, solution-cast and melt-mixed PC/PMMA blends were all phase separated, which may be attributed to the “solvent” effect and LCST behavior, respectively, not discovered in previous reports. Methanol precipitation does not lead to fully mixed blends, which demonstrates the importance of the choice of nonsolvent when using the precipitation method.     

Conformational analysis of dipeptide‐derived polyisocyanides

The conformational properties of polymers derived from isocyanodipeptides have been investigated with a combination of model calculations, X‐ray diffraction, and circular dichroism spectroscopy. Depending on the configuration of the side chains, defined arrays of hydrogen bonds along the polymeric backbone are formed. This leads to a well‐defined conformation as, for example, expressed in the formation of lyotropic liquid‐crystalline phases and increased helical stability. Upon the disruption of the hydrogen bonds by a strong acid, a less well‐defined macromolecular conformation is observed. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 1725–1736, 2003     

Ein Verfahren zur Trennung des Zinks von allen Metallen seiner Gruppe

Ohne Zusammenfassung     

Vascular morphology by three-dimensional magnetic resonance imaging

A three-dimensional examination of blood vessels is provided using MR data from seven cases. The vascular surfaces are constructed with an algorithm that automatically follows the selected artery or vein and generates a projected three-dimensional gradient shaded image. Fast 3DFT pulse sequences were optimized to enhance the time-of-flight contrast of the intravascular region. By increasing the surface threshold value in a three-dimensional head study, the flesh of a patient's face was peeled away to demonstrate the superfacial temporal artery. Gated cardiac images show the great vessels and cardiac chambers. A three-dimensional view of the aorta shows an irregular surface in the vicinity of an adrenal tumor. 3D MR exams provide a non-invasive technique for assessing vascular morphology in a clinical setting.     

Anionic iron(II) alkoxides as initiators for the controlled ring‐opening polymerization of lactide

Hetero‐bimetallic Fe(II) alkoxide/aryloxides were evaluated as initiators for the ring‐opening polymerization of rac‐lactide. [(THF)NaFe(O^tBu)₃]₂ ( 1 ) and [(THF)₄Na₂Fe(2,6‐diisopropylphenolate)₄] ( 2 ) (THF = tetrahydrofuran) both polymerized lactide efficiently at room temperature, with complex 1 affording better control over the molecular weight parameters of the resultant polymer. At conversions below 70%, a linear increase in molecular weight with conversion was observed, indicative of a well‐controlled polymerization process. Complex 2 is the first example of a dianionic Fe(II) alkoxide and has been structurally characterized to reveal a distorted square planar FeO₄ array in which both Na counterions bridge two aryloxide ligands and are further complexed by two THF ligands. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 3798–3803, 2003     

Buckling of a stiff thin film on a compliant substrate in large deformation

A finite-deformation theory is developed to study the mechanics of thin buckled films on compliant substrates. Perturbation analysis is performed for this highly nonlinear system to obtain the analytical solution. The results agree well with experiments and finite element analysis in wavelength and amplitude. In particular, it is found that the wavelength depends on the strain. Based on the accurate wavelength and amplitude, the membrane and peak strains in thin films, and stretchability and compressibility of the system are also obtained analytically.     

Stress concentration and effective stiffness of aligned fiber reinforced composite with anisotropic constituents

The paper addresses the problem of calculation of the local stress field and effective elastic properties of a unidirectional fiber reinforced composite with anisotropic constituents. For this aim, the representative unit cell approach has been utilized. The micro geometry of the composite is modeled by a periodic structure with a unit cell containing multiple circular fibers. The number of fibers is sufficient to account for the micro structure statistics of composite. A new method based on the multipole expansion technique is developed to obtain the exact series solution for the micro stress field. The method combines the principle of superposition, technique of complex potentials and some new results in the theory of special functions. A proper choice of potentials and new results for their series expansions allow one to reduce the boundary-value problem for the multiple-connected domain to an ordinary, well-posed set of linear algebraic equations. This reduction provides high numerical efficiency of the developed method. Exact expressions for the components of the effective stiffness tensor have been obtained by analytical averaging of the strain and stress fields.     

Combined supercritical-fluid chromatography/mass spectrometry in the analysis of diuron in plasma using on-line phase-system switching

On-line sample pretreatment by means of the phase-system switching approach is an interesting technique for the analysis of aqueous samples, e.g., plasma, by means of supercritical-fluid chromatography. In order to analyse plasma samples the following analytical procedure is used. The plasma sample is injected on to a short precolumn, which is washed with water and subsequently dried with nitrogen. Next, the solutes are desorbed with the supercritical mobile phase, analysed with packed-column supercritical-fluid chromatography and detected with either a UV detector or a mass spectrometer, equipped with a moving-belt interface. The herbicide diuron is selected as a test compound to study the feasibility of this approach. Using a selective detector the procedure is sufficiently sensitive to detect diuron in plasma, but not appropriate to detect the diuron metabolites in a post-mortem plasma sample. These have been identified with liquid chromatography/mass spectrometry. The detection limit of diuron in plasma using the procedure described is about 30 ng/mL.