Non-destructive rapid analysis of brominated flame retardants in electrical and electronic equipment using Raman spectroscopy.

Using Raman spectroscopy without any preparation, we analyzed the brominated flame retardant, polybromodiphenyl ethers (PBDEs), which has been prohibited by the European Union. The typical Raman bands of PBDEs, which are clearly different from those of other brominated flame retardants, are from 100 to 300 cm(-1). In our analysis, the detection limit was about 100 ppm, and the analysis took about 1 min, whereas the usual method of solvent extraction using gas chromatography/mass spectroscopy takes 50 h.     

1,1-bis(trimethylsilyl)-1-alkanols as silylcarbene equivalent

Silylcarbenes are generated by the pyrolysis of 1,1-bis(trimethylsilyl)-1-alkanols with elimination of trimethylsilanol.     

Temperature and Oxygen Partial Pressure Dependences of the Surface Tension of Liquid Sn–Ag and Sn–Cu Lead-free Solder Alloys

Temperature dependence of the surface tension of liquid Sn–Ag and Sn–Cu base lead-free solder alloys and oxygen partial pressure dependence of liquid Sn–Ag alloy were evaluated using the experimental data obtained, respectively, by the constrained drop method and the sessile drop method in the previous studies [1, 2]. The temperature dependences of the surface tension have maximum positive values when the mol fraction of Ag and Cu is about 0.7, while those for pure liquid Sn, Ag, and Cu have negative values. The calculated values based on Butler’s equations were found to be in reasonable agreement with those of the experimental data. The oxygen partial pressure dependences of the surface tension of liquid Sn–Ag alloys at 1253 K have a minimum value when the mol fraction of Ag is about 0.9 and the oxygen partial pressure is less than about 10⁻¹³ atm. From this, it is considered that the oxygen adsorption increased by adding Ag to Sn when the mol fraction of Ag is less than 0.9.     

An economical approach for peptide synthesis via regioselective C–N bond cleavage of lactams

An economical, solvent-free, and metal-free method for peptide synthesis via C–N bond cleavage using lactams has been developed. The method not only eliminates the need for condensation agents and their auxiliaries, which are essential for conventional peptide synthesis, but also exhibits high atom economy. The reaction is versatile because it can tolerate side chains bearing a range of functional groups, affording up to >99% yields of the corresponding peptides without racemisation or polymerisation. Moreover, the developed strategy enables peptide segment coupling, providing access to a hexapeptide that occurs as a repeat sequence in spider silk proteins.

An economical, solvent-free, and metal-free method for peptide synthesis via C–N bond cleavage using lactams has been developed.     

A system for measuring absolute frequencies of up to 4.25 THz using a Josephson point contact

A system for measuring the absolute frequency of a far-infrared (FIR) laser is described. Josephson point contacts have been utilized in the system as a frequency harmonic mixer connecting microwaves and optically pumped CH₃OH laser lines. The Josephson point contacts are capable of generating beat signals of 90 GHz microwaves and FIR waves of up to 4.25 THz. To measure the frequency of the beat signals from the Josephson junction with a frequency counter, tracking oscillators have been developed, which tracks the beat signals by phase locking and regenerate clean signals for frequency counting. It is shown that the absolute frequency can be measured to an accuracy of about 100 Hz by using the tracking oscillators.     

Estimation of the Refractive Index Change in Glass Induced by Femtosecond Laser Pulses

It is known that local refractive index change occurs when femtosecond laser pulses with extremely high peak power are launched into glass. We focused 130-femtosecond laser pulses of 800 nm into the bulk of glass and examined the shape of the induced refractive index change. We found that the length of the spot of the refractive index change along the optical axis reached about 30 μm despite the diameter being about 2 μm. To estimate the distribution of induced refractive index change, we fabricated Bragg grating by scanning the focused spot and calculated the amount of the change by applying Kogelnik’s coupled mode theory to the measured diffraction efficiencies of the higher order diffracted beams.     

A cylindrical micro-ultrasonic motor (stator transducer size: 1.4 mm in diameter and 5.0 mm long)

Ultrasonic motors are suitable for a micro-actuator because of a direct drive, no brake and their simple construction. In order to fabricate micro-ultrasonic motors, a piezoelectric thin film is essential. In this study, a hydrothermal method was adopted to deposit a PZT thin film. The dimensions of the stator transducer were: outer diameter, 1.4 mm; inner diameter, 1.2 mm; and length, 5.0 mm. The resonance frequency of the stator transducer was 227 kHz, and the vibration amplitude was 58 nmp-p at an input voltage of 4.0 Vp-p. The maximum revolution speed was 680 rpm, and the maximum starting torque was 0.67 microNm. The experimental conditions were 20 Vp-p and 5.3 mN pre-load. The motor property versus scale was investigated using an equivalent circuit. The calculated results indicated that the output torque of the 100 microns diameter motor was 27 nNm.     

Optical and Thermal Simulator for Laser-assisted Magnetic Recording

“Laser-assisted magnetic recording”, in which a recording media is heated by a laser beam while writing data, is attracting attention as a technology that enables a recording density of 1 Tb/in.². There exists another technology for media in which the recording layer is constructed with many small projections that enable high magnetic coercivity. This is called “patterned media”. For developing hard disk drives using these methods, we developed a simulator that analyzes the optical intensity distribution from the optical head for laser-assisted recording and the temperature profile on the patterned media. The simulator calculates the optical model using the finite-difference time-domain (FDTD) method. The thermal analysis of the three-dimensional model allows fast calculations using the alternating direction implicit (ADI) method. The heat source distribution data for thermal analysis is calculated in order to use the results of optical analysis. The optical and thermal analyses of the laser-assisted recording model were investigated with the simulator.     

Subwavelength-size solid immersion lens

We report on the fabrication and characterization of nanoscale solid immersion lenses (nano-SILs) with sizes down to a subwavelength range. Submicrometer-scale cylinders fabricated by electron-beam lithography are thermally reflowed to form a spherical shape. Subsequent soft lithography leads to nano-SILs on transparent substrates for optical characterization. The optical characterization is performed using a high-resolution interference microscope with illumination at 642 nm wavelength. The focal spots produced by the nano-SILs show both spot-size reduction and enhanced optical intensity, which are consistent with the immersion effect.     

Development of Non-Halogen Flame Retardant Optical Fiber and Optical Fiber Cord

A non-halogen highly flame-retardant 0.9mm optical fiber and 2.0mm simplex optical cord, which are harmonized with the ecosystem, have been developed. The characteristics of them are presented in this paper.